Services
Service Areas
Mobile ADAS Calibration for Daihatsu Mira Tocot: What to Expect On-Site and Why Setup Matters
Confirm Daihatsu Mira Tocot Calibration Requirements and Which ADAS Systems Are Involved
Before we arrive for mobile ADAS calibration on your Daihatsu Mira Tocot, we confirm the OEM procedure for that exact vehicle: year, trim, and options. ADAS is a network of modules, not a single feature: a forward windshield camera, front radar behind the grille, side or corner radars for blind-spot monitoring, rear sensors for parking and cross-traffic alerts, and sometimes surround-view cameras. These inputs support lane keeping assist, adaptive cruise control, forward collision warning, automatic emergency braking, pedestrian detection, traffic sign recognition, and more. Because rules vary by platform, we verify which systems are installed, which modules are requesting calibration, and what event triggered it: windshield replacement, camera or radar service, bumper or grille work, collision repairs, wheel alignment, suspension or ride-height changes, or stored diagnostic trouble codes. Using OEM service information and professional lookup tools, Bang AutoGlass identifies prerequisites, the correct guided routine, and the documentation we will produce. That verification happens before targets go up or a road procedure begins, so you get a clear on-site plan and OEM-aligned steps for your Daihatsu Mira Tocot.
Mobile ADAS Calibration Types for Daihatsu Mira Tocot: Static, Dynamic, or Both
When mobile ADAS Calibration is performed on a Daihatsu Mira Tocot, the workflow is typically static, dynamic, or both. Static calibration is completed with the vehicle parked while targets are placed at precise distances and heights so the camera or radar can compute aim and centerline offsets from controlled geometry. Dynamic calibration completes during a drive where the Daihatsu Mira Tocot uses lane markings and stable motion to learn or verify offsets, often requiring defined speed ranges and enough uninterrupted time to meet completion criteria. Many platforms combine methods, such as a static camera baseline followed by a dynamic verification drive, or separate static routines for camera and radar plus initialization of steering angle or stability references. From a mobile standpoint, static success is environment control: flat surface, sufficient lot depth for target distance, and precise measurements. Dynamic success is route control: clear lane lines, manageable traffic, and a safe place to hold speed without repeated stops. Weather and visibility matter; glare, heavy rain, fog, or poor markings can prevent dynamic completion even if the scan tool starts the routine. Regardless of method, 'done' means completed routine status and a clean post-scan for the Daihatsu Mira Tocot, not just a cleared warning light.
On-Site Setup Matters: Level Surface, Space, Lighting, and Target Distances
For mobile ADAS calibration, on-site setup is the foundation for accuracy on your Daihatsu Mira Tocot. Static routines depend on precise geometry, so we start with a level surface and a stable vehicle stance; even slight slope or an uneven driveway crown can skew pitch or roll and change camera or radar aim. Lighting is also a control point: direct sun, glare, harsh shadows, and reflective surfaces can interfere with what a camera sees during target learning and reduce repeatability. Space matters because targets must be placed at OEM-specified distances and offsets with a clean line of sight; walls, poles, parked cars, and tight bays can compromise alignment. As a practical reference, many setups call for a work area roughly in the 25 ft x 34 ft minimum range, with 30 ft x 45 ft often more comfortable, depending on the OEM procedure. Target placement is measured from defined points such as the front axle centerline or thrust line, never by eye. When Bang AutoGlass arrives, we evaluate the site first, then measure, align, and verify the environment so mobile calibration is both convenient and correct for your Daihatsu Mira Tocot.
Pre-Calibration Checklist for Daihatsu Mira Tocot: Pre-Scan, DTC Review, and Vehicle Readiness
Before mobile ADAS Calibration starts on a Daihatsu Mira Tocot, a structured readiness check prevents failures caused by unmet prerequisites. Begin with a pre-scan to capture DTCs and module status, confirming which controllers are requesting calibration and whether any network or voltage faults would invalidate the procedure. This also reveals prerequisite routines—such as steering angle initialization—that must be completed before target setup. Next, confirm chassis geometry and stability. ADAS calibration assumes correct tire size, equal tire pressures, and normal ride height. Uneven loading, suspension modifications, or a sagging stance can skew the reference axis the Daihatsu Mira Tocot learns. Alignment matters too: toe and thrust angle influence straight-ahead calculations, so calibrating a vehicle with a pull or recent suspension work that hasn’t been aligned is risky. Power stability is another common blocker. Mobile sessions may require extended ignition-on time, and voltage drops can interrupt a routine or set false codes, so battery support helps. Then validate the physical baseline: confirm proper windshield fit, secure camera bracket/cover, a clean camera viewing area, and correctly mounted radar/sensors with unobstructed fields of view after bumper work. If dynamic steps are required, confirm the vehicle is safe to drive and nearby roads meet lane-marking and speed requirements.
What to Expect During On-Site Calibration: Target Alignment, Scan Tool Steps, and Road Procedure
During mobile ADAS Calibration for a Daihatsu Mira Tocot, the appointment follows a scan-guided sequence that controls both vehicle state and calibration order. We start by selecting the correct routine in the scan tool, confirming the module(s) involved, and placing the system into service mode so driver-assist features are ready for recalibration. For static steps, the Daihatsu Mira Tocot is positioned precisely, a centerline reference is established, and targets are placed using measured distances and heights. The scan tool prompts actions such as steering centering, brake holds, ignition cycles, and measurement confirmations while the module captures reference images/returns and computes offsets. Precision is what makes the calibration durable. Small errors in yaw, target height, or distance can later present as lane-centering bias, false alerts, or restricted adaptive cruise. If the procedure includes a dynamic phase, it follows only after the stationary step is accepted. Dynamic calibration is a controlled drive where the Daihatsu Mira Tocot must maintain specified speeds with clear lane markings until the tool indicates completion; congestion and poor markings can pause progress. Throughout the workflow, newly set DTCs are treated as diagnostic signals—obstruction, voltage instability, mounting issues, or unmet prerequisites—rather than something to clear and ignore. Once complete, a post-scan confirms clean module health, cleared warnings, and normal feature availability.
Proof and Documentation: Post-Scan Results, Verification, and Records for Daihatsu Mira Tocot
Mobile ADAS Calibration is best closed out with objective proof, and for a Daihatsu Mira Tocot that proof is typically the pre-scan/post-scan record plus documented routine completion. A strong record shows what codes and module conditions existed before service, which calibration routines were performed, and whether any related faults remained afterward. Documentation should name the systems addressed—forward camera calibration, radar aiming/verification, steering angle initialization, sensor-fusion validation—so scope is explicit. Where possible, capture the scan-tool routine name and completed status to tie results to the correct workflow for that Daihatsu Mira Tocot configuration. This evidence supports safety assurance, claim records, and future diagnostics. It establishes a baseline that can be referenced after later alignment, suspension changes, another windshield replacement, or repairs that affect sensor geometry. It also shows ADAS Calibration was performed as a necessary step after glass or front-end work rather than a discretionary add-on. Good documentation includes date/time, technician identification, method (static, dynamic, or both), and brief notes on verified prerequisites (level surface, tire pressures normalized, battery support used). If a dynamic drive was required, note general completion conditions. After documentation is generated, confirm warnings are off and features can be enabled; if completion isn’t possible on-site, document the limiting factor and recommended next step.
Services
Service Areas
Mobile ADAS Calibration for Daihatsu Mira Tocot: What to Expect On-Site and Why Setup Matters
Confirm Daihatsu Mira Tocot Calibration Requirements and Which ADAS Systems Are Involved
Before we arrive for mobile ADAS calibration on your Daihatsu Mira Tocot, we confirm the OEM procedure for that exact vehicle: year, trim, and options. ADAS is a network of modules, not a single feature: a forward windshield camera, front radar behind the grille, side or corner radars for blind-spot monitoring, rear sensors for parking and cross-traffic alerts, and sometimes surround-view cameras. These inputs support lane keeping assist, adaptive cruise control, forward collision warning, automatic emergency braking, pedestrian detection, traffic sign recognition, and more. Because rules vary by platform, we verify which systems are installed, which modules are requesting calibration, and what event triggered it: windshield replacement, camera or radar service, bumper or grille work, collision repairs, wheel alignment, suspension or ride-height changes, or stored diagnostic trouble codes. Using OEM service information and professional lookup tools, Bang AutoGlass identifies prerequisites, the correct guided routine, and the documentation we will produce. That verification happens before targets go up or a road procedure begins, so you get a clear on-site plan and OEM-aligned steps for your Daihatsu Mira Tocot.
Mobile ADAS Calibration Types for Daihatsu Mira Tocot: Static, Dynamic, or Both
When mobile ADAS Calibration is performed on a Daihatsu Mira Tocot, the workflow is typically static, dynamic, or both. Static calibration is completed with the vehicle parked while targets are placed at precise distances and heights so the camera or radar can compute aim and centerline offsets from controlled geometry. Dynamic calibration completes during a drive where the Daihatsu Mira Tocot uses lane markings and stable motion to learn or verify offsets, often requiring defined speed ranges and enough uninterrupted time to meet completion criteria. Many platforms combine methods, such as a static camera baseline followed by a dynamic verification drive, or separate static routines for camera and radar plus initialization of steering angle or stability references. From a mobile standpoint, static success is environment control: flat surface, sufficient lot depth for target distance, and precise measurements. Dynamic success is route control: clear lane lines, manageable traffic, and a safe place to hold speed without repeated stops. Weather and visibility matter; glare, heavy rain, fog, or poor markings can prevent dynamic completion even if the scan tool starts the routine. Regardless of method, 'done' means completed routine status and a clean post-scan for the Daihatsu Mira Tocot, not just a cleared warning light.
On-Site Setup Matters: Level Surface, Space, Lighting, and Target Distances
For mobile ADAS calibration, on-site setup is the foundation for accuracy on your Daihatsu Mira Tocot. Static routines depend on precise geometry, so we start with a level surface and a stable vehicle stance; even slight slope or an uneven driveway crown can skew pitch or roll and change camera or radar aim. Lighting is also a control point: direct sun, glare, harsh shadows, and reflective surfaces can interfere with what a camera sees during target learning and reduce repeatability. Space matters because targets must be placed at OEM-specified distances and offsets with a clean line of sight; walls, poles, parked cars, and tight bays can compromise alignment. As a practical reference, many setups call for a work area roughly in the 25 ft x 34 ft minimum range, with 30 ft x 45 ft often more comfortable, depending on the OEM procedure. Target placement is measured from defined points such as the front axle centerline or thrust line, never by eye. When Bang AutoGlass arrives, we evaluate the site first, then measure, align, and verify the environment so mobile calibration is both convenient and correct for your Daihatsu Mira Tocot.
Pre-Calibration Checklist for Daihatsu Mira Tocot: Pre-Scan, DTC Review, and Vehicle Readiness
Before mobile ADAS Calibration starts on a Daihatsu Mira Tocot, a structured readiness check prevents failures caused by unmet prerequisites. Begin with a pre-scan to capture DTCs and module status, confirming which controllers are requesting calibration and whether any network or voltage faults would invalidate the procedure. This also reveals prerequisite routines—such as steering angle initialization—that must be completed before target setup. Next, confirm chassis geometry and stability. ADAS calibration assumes correct tire size, equal tire pressures, and normal ride height. Uneven loading, suspension modifications, or a sagging stance can skew the reference axis the Daihatsu Mira Tocot learns. Alignment matters too: toe and thrust angle influence straight-ahead calculations, so calibrating a vehicle with a pull or recent suspension work that hasn’t been aligned is risky. Power stability is another common blocker. Mobile sessions may require extended ignition-on time, and voltage drops can interrupt a routine or set false codes, so battery support helps. Then validate the physical baseline: confirm proper windshield fit, secure camera bracket/cover, a clean camera viewing area, and correctly mounted radar/sensors with unobstructed fields of view after bumper work. If dynamic steps are required, confirm the vehicle is safe to drive and nearby roads meet lane-marking and speed requirements.
What to Expect During On-Site Calibration: Target Alignment, Scan Tool Steps, and Road Procedure
During mobile ADAS Calibration for a Daihatsu Mira Tocot, the appointment follows a scan-guided sequence that controls both vehicle state and calibration order. We start by selecting the correct routine in the scan tool, confirming the module(s) involved, and placing the system into service mode so driver-assist features are ready for recalibration. For static steps, the Daihatsu Mira Tocot is positioned precisely, a centerline reference is established, and targets are placed using measured distances and heights. The scan tool prompts actions such as steering centering, brake holds, ignition cycles, and measurement confirmations while the module captures reference images/returns and computes offsets. Precision is what makes the calibration durable. Small errors in yaw, target height, or distance can later present as lane-centering bias, false alerts, or restricted adaptive cruise. If the procedure includes a dynamic phase, it follows only after the stationary step is accepted. Dynamic calibration is a controlled drive where the Daihatsu Mira Tocot must maintain specified speeds with clear lane markings until the tool indicates completion; congestion and poor markings can pause progress. Throughout the workflow, newly set DTCs are treated as diagnostic signals—obstruction, voltage instability, mounting issues, or unmet prerequisites—rather than something to clear and ignore. Once complete, a post-scan confirms clean module health, cleared warnings, and normal feature availability.
Proof and Documentation: Post-Scan Results, Verification, and Records for Daihatsu Mira Tocot
Mobile ADAS Calibration is best closed out with objective proof, and for a Daihatsu Mira Tocot that proof is typically the pre-scan/post-scan record plus documented routine completion. A strong record shows what codes and module conditions existed before service, which calibration routines were performed, and whether any related faults remained afterward. Documentation should name the systems addressed—forward camera calibration, radar aiming/verification, steering angle initialization, sensor-fusion validation—so scope is explicit. Where possible, capture the scan-tool routine name and completed status to tie results to the correct workflow for that Daihatsu Mira Tocot configuration. This evidence supports safety assurance, claim records, and future diagnostics. It establishes a baseline that can be referenced after later alignment, suspension changes, another windshield replacement, or repairs that affect sensor geometry. It also shows ADAS Calibration was performed as a necessary step after glass or front-end work rather than a discretionary add-on. Good documentation includes date/time, technician identification, method (static, dynamic, or both), and brief notes on verified prerequisites (level surface, tire pressures normalized, battery support used). If a dynamic drive was required, note general completion conditions. After documentation is generated, confirm warnings are off and features can be enabled; if completion isn’t possible on-site, document the limiting factor and recommended next step.
Services
Service Areas
Mobile ADAS Calibration for Daihatsu Mira Tocot: What to Expect On-Site and Why Setup Matters
Confirm Daihatsu Mira Tocot Calibration Requirements and Which ADAS Systems Are Involved
Before we arrive for mobile ADAS calibration on your Daihatsu Mira Tocot, we confirm the OEM procedure for that exact vehicle: year, trim, and options. ADAS is a network of modules, not a single feature: a forward windshield camera, front radar behind the grille, side or corner radars for blind-spot monitoring, rear sensors for parking and cross-traffic alerts, and sometimes surround-view cameras. These inputs support lane keeping assist, adaptive cruise control, forward collision warning, automatic emergency braking, pedestrian detection, traffic sign recognition, and more. Because rules vary by platform, we verify which systems are installed, which modules are requesting calibration, and what event triggered it: windshield replacement, camera or radar service, bumper or grille work, collision repairs, wheel alignment, suspension or ride-height changes, or stored diagnostic trouble codes. Using OEM service information and professional lookup tools, Bang AutoGlass identifies prerequisites, the correct guided routine, and the documentation we will produce. That verification happens before targets go up or a road procedure begins, so you get a clear on-site plan and OEM-aligned steps for your Daihatsu Mira Tocot.
Mobile ADAS Calibration Types for Daihatsu Mira Tocot: Static, Dynamic, or Both
When mobile ADAS Calibration is performed on a Daihatsu Mira Tocot, the workflow is typically static, dynamic, or both. Static calibration is completed with the vehicle parked while targets are placed at precise distances and heights so the camera or radar can compute aim and centerline offsets from controlled geometry. Dynamic calibration completes during a drive where the Daihatsu Mira Tocot uses lane markings and stable motion to learn or verify offsets, often requiring defined speed ranges and enough uninterrupted time to meet completion criteria. Many platforms combine methods, such as a static camera baseline followed by a dynamic verification drive, or separate static routines for camera and radar plus initialization of steering angle or stability references. From a mobile standpoint, static success is environment control: flat surface, sufficient lot depth for target distance, and precise measurements. Dynamic success is route control: clear lane lines, manageable traffic, and a safe place to hold speed without repeated stops. Weather and visibility matter; glare, heavy rain, fog, or poor markings can prevent dynamic completion even if the scan tool starts the routine. Regardless of method, 'done' means completed routine status and a clean post-scan for the Daihatsu Mira Tocot, not just a cleared warning light.
On-Site Setup Matters: Level Surface, Space, Lighting, and Target Distances
For mobile ADAS calibration, on-site setup is the foundation for accuracy on your Daihatsu Mira Tocot. Static routines depend on precise geometry, so we start with a level surface and a stable vehicle stance; even slight slope or an uneven driveway crown can skew pitch or roll and change camera or radar aim. Lighting is also a control point: direct sun, glare, harsh shadows, and reflective surfaces can interfere with what a camera sees during target learning and reduce repeatability. Space matters because targets must be placed at OEM-specified distances and offsets with a clean line of sight; walls, poles, parked cars, and tight bays can compromise alignment. As a practical reference, many setups call for a work area roughly in the 25 ft x 34 ft minimum range, with 30 ft x 45 ft often more comfortable, depending on the OEM procedure. Target placement is measured from defined points such as the front axle centerline or thrust line, never by eye. When Bang AutoGlass arrives, we evaluate the site first, then measure, align, and verify the environment so mobile calibration is both convenient and correct for your Daihatsu Mira Tocot.
Pre-Calibration Checklist for Daihatsu Mira Tocot: Pre-Scan, DTC Review, and Vehicle Readiness
Before mobile ADAS Calibration starts on a Daihatsu Mira Tocot, a structured readiness check prevents failures caused by unmet prerequisites. Begin with a pre-scan to capture DTCs and module status, confirming which controllers are requesting calibration and whether any network or voltage faults would invalidate the procedure. This also reveals prerequisite routines—such as steering angle initialization—that must be completed before target setup. Next, confirm chassis geometry and stability. ADAS calibration assumes correct tire size, equal tire pressures, and normal ride height. Uneven loading, suspension modifications, or a sagging stance can skew the reference axis the Daihatsu Mira Tocot learns. Alignment matters too: toe and thrust angle influence straight-ahead calculations, so calibrating a vehicle with a pull or recent suspension work that hasn’t been aligned is risky. Power stability is another common blocker. Mobile sessions may require extended ignition-on time, and voltage drops can interrupt a routine or set false codes, so battery support helps. Then validate the physical baseline: confirm proper windshield fit, secure camera bracket/cover, a clean camera viewing area, and correctly mounted radar/sensors with unobstructed fields of view after bumper work. If dynamic steps are required, confirm the vehicle is safe to drive and nearby roads meet lane-marking and speed requirements.
What to Expect During On-Site Calibration: Target Alignment, Scan Tool Steps, and Road Procedure
During mobile ADAS Calibration for a Daihatsu Mira Tocot, the appointment follows a scan-guided sequence that controls both vehicle state and calibration order. We start by selecting the correct routine in the scan tool, confirming the module(s) involved, and placing the system into service mode so driver-assist features are ready for recalibration. For static steps, the Daihatsu Mira Tocot is positioned precisely, a centerline reference is established, and targets are placed using measured distances and heights. The scan tool prompts actions such as steering centering, brake holds, ignition cycles, and measurement confirmations while the module captures reference images/returns and computes offsets. Precision is what makes the calibration durable. Small errors in yaw, target height, or distance can later present as lane-centering bias, false alerts, or restricted adaptive cruise. If the procedure includes a dynamic phase, it follows only after the stationary step is accepted. Dynamic calibration is a controlled drive where the Daihatsu Mira Tocot must maintain specified speeds with clear lane markings until the tool indicates completion; congestion and poor markings can pause progress. Throughout the workflow, newly set DTCs are treated as diagnostic signals—obstruction, voltage instability, mounting issues, or unmet prerequisites—rather than something to clear and ignore. Once complete, a post-scan confirms clean module health, cleared warnings, and normal feature availability.
Proof and Documentation: Post-Scan Results, Verification, and Records for Daihatsu Mira Tocot
Mobile ADAS Calibration is best closed out with objective proof, and for a Daihatsu Mira Tocot that proof is typically the pre-scan/post-scan record plus documented routine completion. A strong record shows what codes and module conditions existed before service, which calibration routines were performed, and whether any related faults remained afterward. Documentation should name the systems addressed—forward camera calibration, radar aiming/verification, steering angle initialization, sensor-fusion validation—so scope is explicit. Where possible, capture the scan-tool routine name and completed status to tie results to the correct workflow for that Daihatsu Mira Tocot configuration. This evidence supports safety assurance, claim records, and future diagnostics. It establishes a baseline that can be referenced after later alignment, suspension changes, another windshield replacement, or repairs that affect sensor geometry. It also shows ADAS Calibration was performed as a necessary step after glass or front-end work rather than a discretionary add-on. Good documentation includes date/time, technician identification, method (static, dynamic, or both), and brief notes on verified prerequisites (level surface, tire pressures normalized, battery support used). If a dynamic drive was required, note general completion conditions. After documentation is generated, confirm warnings are off and features can be enabled; if completion isn’t possible on-site, document the limiting factor and recommended next step.
Enjoy More Relevant Blogs
Tempered vs Laminated Door Glass on Dodge Ram 2500 Regular Cab: What’s Used and Why It Matters
Tempered vs laminated door glass on Dodge Ram 2500 Regular Cab: what your vehicle uses, how it breaks, and what it means for replacement safety, cost, and cleanup.
How to Schedule ADAS Calibration for Ford F250 Super Duty Crew Cab After Windshield Replacement
Schedule ADAS calibration for Ford F250 Super Duty Crew Cab after windshield replacement. Learn timing, required info, and what to expect so safety systems stay accurate.
After a Break-In: Dodge Challenger Quarter Glass Replacement Plan to Restore Security and Visibility
After a break-in on Dodge Challenger, restore security with a quarter glass replacement plan: cleanup, temporary protection, scheduling, and post-install checks.
Will Insurance Cover Door Glass Replacement for a Ford Focus RS? Claims Steps, Deductibles, and What to Document
Will insurance cover Ford Focus RS door glass replacement? Learn claim steps, deductibles, photos to document, and how to schedule fast repairs today.
ADAS After Windshield Replacement on Gmc Terrain: Calibration Basics and Safety Checks
ADAS after Gmc Terrain windshield replacement: calibration basics, common safety checks, and how to confirm cameras and sensors are working correctly.
How to Schedule Mobile Rear Glass Replacement for Gmc Rally Wagon 2500
Schedule mobile rear glass replacement for your Gmc Rally Wagon 2500 in minutes. Learn what info to provide, how long it takes, and prep tips for service day.
Stop Leaks and Wind Noise: What Proper Dodge Durango Quarter Glass Replacement Should Prevent
Stop leaks and wind noise with proper Dodge Durango quarter glass replacement. Learn what correct fit, sealing, and trim should prevent after install.
Tempered Safety Rear Glass Replacement for Gmc Canyon Crew Cab: Understanding DOT Markings and FMVSS 205
Need Gmc Canyon Crew Cab rear glass replacement? Learn tempered safety glass basics, DOT markings, and FMVSS 205, plus install and cure tips. Get a quote today.
Post-Install Checks for Gmc Sierra (Classic) 1500 Extended Cab: Rear Glass Replacement Wind Noise, Leaks, and Rattle Tests
Post-install rear glass checks for Gmc Sierra (Classic) 1500 Extended Cab: test for wind noise, leaks, and rattles, plus when to return for warranty service—check today before trips.
Fast Scheduling Guide: Gmc Sierra 3500 Hd Extended Cab Windshield Replacement From Booking to Install
Book Gmc Sierra 3500 Hd Extended Cab windshield replacement fast. See scheduling steps, what to prep, install timing, and when you can safely drive away. Get a quote today.
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm