Services
Service Areas
OEM Calibration Requirements for Ford Ranger Raptor: How to Confirm What Must Be Calibrated
Start With VIN-Specific ADAS Feature Identification for Ford Ranger Raptor
OEM ADAS Calibration requirements for a Ford Ranger Raptor are only reliable when you start from a VIN-verified ADAS configuration. ADAS content is option-driven, so two Ford Ranger Raptor vehicles can have different camera or radar packages even if they share the same appearance. Decode the VIN, confirm option codes, and list the driver-assist features present: lane keeping or centering, adaptive cruise, forward collision warning, automatic emergency braking, traffic sign recognition, blind-spot monitoring and rear cross-traffic alerts, and any parking or surround-view features. Next, connect features to hardware by confirming sensor locations and the modules that process them. For many Ford Ranger Raptor setups, that means a forward camera behind the windshield and radar sensors in the grille or bumper area, plus any corner sensors used for cross-traffic logic. Note supporting sensors the OEM may treat as prerequisites (steering angle, yaw rate, ride-height). Document the configuration in a short VIN record: features present, sensors and modules present, and mounting locations. With that foundation, decisions about static calibration, dynamic calibration, sequencing, and proof are tied to the exact Ford Ranger Raptor you serviced, not assumptions that can lead to intermittent warnings later. This inventory clarifies which repairs can disturb geometry and which modules must be validated.
Find the OEM Source of Truth: Service Info, Bulletins, and Position Statements
After you confirm which ADAS features your Ford Ranger Raptor has, verify calibration requirements from the manufacturer—not from generic charts. OEM requirements typically live in official service information (factory manuals and diagnostic routines), Technical Service Bulletins (TSBs) that update triggers or prerequisites, and OEM position statements that outline expectations for safe, compliant repairs. When confirming what must be calibrated, prioritize what the OEM publishes for the correct model year and VIN-level equipment. Position statements are especially useful for windshield and camera work because they address common scenarios: proper camera mounting, use of OEM-spec glass, pre-scan and post-scan guidance, and when calibration is mandatory. Many OEM documents directly connect windshield replacement to the performance of automatic emergency braking, lane keep assist, forward collision warning, and adaptive cruise control. Industry reference tools can help you find likely requirements faster, but treat them as a starting point—the OEM procedure is the authority for an OEM-compliant plan. To stay OEM-correct, confirm you are using the latest revision and document what you referenced. That record supports liability protection, customer confidence, and insurance approvals. Bang AutoGlass keeps scheduling simple with next-day mobile service, and we can work with any insurance company if you have comprehensive coverage.
Map Calibration Triggers on Ford Ranger Raptor: What Repairs Commonly Require Recalibration
A trigger map is a fast way to confirm what must be calibrated on a Ford Ranger Raptor for OEM ADAS Calibration. Start with windshield-related events: if the forward camera mounts behind the glass, windshield replacement commonly requires calibration because camera seating, bracket alignment, and the camera-to-glass relationship define the optical axis. Any bracket replacement, re-bond, or movement is a direct trigger when the OEM specifies ADAS Calibration. Next, evaluate front-end work. Radar sensors and brackets in the grille or bumper area can be disturbed during collision repairs, bumper removal, grille replacement, or bracket service, and recalibration may be required even if no warning light is present. Add geometry triggers: wheel alignment changes, toe/camber adjustments, suspension repairs, ride-height changes, or tire-size changes can alter how the Ford Ranger Raptor interprets lane position and relative motion. Include sensor movement as a trigger even when a sensor is not replaced; small shifts can skew distance or lane calculations while communication checks still pass. Finally, identify module-specific initialization triggers (steering-angle relearn, yaw-rate reset, battery disconnect effects) that may require a relearn routine instead of full calibration, depending on OEM rules. Document the map as repair event → mount disturbed → module affected → required method so you don’t calibrate one system while missing another.
Run a Pre-Scan and Baseline Checks: DTCs, Warning Lights, and Prerequisites
A reliable way to validate OEM ADAS Calibration needs on Ford Ranger Raptor is to treat the pre-scan and baseline checks as mandatory. Perform a comprehensive pre-scan of ADAS modules and record active and stored DTCs, calibration-required indicators, and status fields showing incomplete learning. Many vehicles request calibration without a constant dash light, so scan output is the confirmation layer; save it for the VIN. Next, verify prerequisites that impact accuracy: correct tire pressure, matched tire size, normal ride height, and stable battery voltage so module communication stays solid. Inspect the camera viewing path: clean the glass at the camera window, confirm the housing is seated, and remove tint edges, adhesives, trim, or accessories that obstruct the field of view. For radar-equipped Ford Ranger Raptor variants, inspect brackets and covers for bends, misalignment, or loose fasteners; calibration will not correct a distorted mount. If recent alignment or suspension work occurred, confirm alignment angles are in spec and steering angle readings make sense. For static ADAS Calibration, confirm your setup can meet OEM conditions (level floor, target placement, lighting control) before starting. This gate prevents repeated failures and reduces unstable alerts after delivery.
Choose the Correct Method: Static vs Dynamic Calibration vs Initialization for Ford Ranger Raptor
Choosing the OEM method for ADAS Calibration on Ford Ranger Raptor is a decision step, not a preference. The procedure may require static calibration, dynamic calibration, a combined sequence, or an initialization/relearn routine, depending on the sensor package and the trigger event. Static ADAS Calibration uses targets and measurements to validate geometry in a controlled space, so it is sensitive to target distance and height, centerline references, lighting, and floor level. Dynamic ADAS Calibration relies on an OEM-defined drive cycle, so it is sensitive to speed window, lane-marking quality, traffic, and weather. Some Ford Ranger Raptor variants require both methods in sequence, and changing the order can leave modules incomplete. Initialization may be required after certain resets (for example, steering angle or yaw-rate relearn), but it does not replace calibration when the OEM calls for it after windshield or bracket disturbance. Use scan evidence and VIN-applicable service information to decide: if DTCs indicate calibration required, follow the routine tied to those codes. Do not start static without the correct target setup, and do not start dynamic if you cannot safely meet the drive requirements. Fix mounting or geometry issues first; calibration cannot compensate for a bent bracket or mis-seated camera.
Verify and Document: Post-Scan Reports, Results, and Proof for Ford Ranger Raptor
For OEM-calibrated ADAS work on your Ford Ranger Raptor, verify and document results before delivery. Start with a post-repair diagnostic scan to confirm DTCs are resolved, warning lights are off, modules communicate, and no new faults were introduced. If calibration was performed, documentation should list the systems addressed (forward camera, radar, lane keep assist, forward collision warning, automatic emergency braking, blind spot monitoring), the method used (static, dynamic, dual, or initialization), and the completion status. Many providers supply a scan report and calibration certificate that ties results to the VIN and timestamps. This proof supports comprehensive insurance claims, reduces delays, and creates a defensible record if questions arise. It also helps future troubleshooting when intermittent alerts appear later, because before-and-after scans establish a baseline. At Bang AutoGlass, we can advise what reports to request and help coordinate scanning and recalibration when required. Pair that with next-day mobile service, a typical 30-45 minute replacement, at least one hour safe drive cure time, acceptance of comprehensive insurance coverage, and a lifetime workmanship warranty. Keep these reports with your invoice for future reference and resale value.
Services
Service Areas
OEM Calibration Requirements for Ford Ranger Raptor: How to Confirm What Must Be Calibrated
Start With VIN-Specific ADAS Feature Identification for Ford Ranger Raptor
OEM ADAS Calibration requirements for a Ford Ranger Raptor are only reliable when you start from a VIN-verified ADAS configuration. ADAS content is option-driven, so two Ford Ranger Raptor vehicles can have different camera or radar packages even if they share the same appearance. Decode the VIN, confirm option codes, and list the driver-assist features present: lane keeping or centering, adaptive cruise, forward collision warning, automatic emergency braking, traffic sign recognition, blind-spot monitoring and rear cross-traffic alerts, and any parking or surround-view features. Next, connect features to hardware by confirming sensor locations and the modules that process them. For many Ford Ranger Raptor setups, that means a forward camera behind the windshield and radar sensors in the grille or bumper area, plus any corner sensors used for cross-traffic logic. Note supporting sensors the OEM may treat as prerequisites (steering angle, yaw rate, ride-height). Document the configuration in a short VIN record: features present, sensors and modules present, and mounting locations. With that foundation, decisions about static calibration, dynamic calibration, sequencing, and proof are tied to the exact Ford Ranger Raptor you serviced, not assumptions that can lead to intermittent warnings later. This inventory clarifies which repairs can disturb geometry and which modules must be validated.
Find the OEM Source of Truth: Service Info, Bulletins, and Position Statements
After you confirm which ADAS features your Ford Ranger Raptor has, verify calibration requirements from the manufacturer—not from generic charts. OEM requirements typically live in official service information (factory manuals and diagnostic routines), Technical Service Bulletins (TSBs) that update triggers or prerequisites, and OEM position statements that outline expectations for safe, compliant repairs. When confirming what must be calibrated, prioritize what the OEM publishes for the correct model year and VIN-level equipment. Position statements are especially useful for windshield and camera work because they address common scenarios: proper camera mounting, use of OEM-spec glass, pre-scan and post-scan guidance, and when calibration is mandatory. Many OEM documents directly connect windshield replacement to the performance of automatic emergency braking, lane keep assist, forward collision warning, and adaptive cruise control. Industry reference tools can help you find likely requirements faster, but treat them as a starting point—the OEM procedure is the authority for an OEM-compliant plan. To stay OEM-correct, confirm you are using the latest revision and document what you referenced. That record supports liability protection, customer confidence, and insurance approvals. Bang AutoGlass keeps scheduling simple with next-day mobile service, and we can work with any insurance company if you have comprehensive coverage.
Map Calibration Triggers on Ford Ranger Raptor: What Repairs Commonly Require Recalibration
A trigger map is a fast way to confirm what must be calibrated on a Ford Ranger Raptor for OEM ADAS Calibration. Start with windshield-related events: if the forward camera mounts behind the glass, windshield replacement commonly requires calibration because camera seating, bracket alignment, and the camera-to-glass relationship define the optical axis. Any bracket replacement, re-bond, or movement is a direct trigger when the OEM specifies ADAS Calibration. Next, evaluate front-end work. Radar sensors and brackets in the grille or bumper area can be disturbed during collision repairs, bumper removal, grille replacement, or bracket service, and recalibration may be required even if no warning light is present. Add geometry triggers: wheel alignment changes, toe/camber adjustments, suspension repairs, ride-height changes, or tire-size changes can alter how the Ford Ranger Raptor interprets lane position and relative motion. Include sensor movement as a trigger even when a sensor is not replaced; small shifts can skew distance or lane calculations while communication checks still pass. Finally, identify module-specific initialization triggers (steering-angle relearn, yaw-rate reset, battery disconnect effects) that may require a relearn routine instead of full calibration, depending on OEM rules. Document the map as repair event → mount disturbed → module affected → required method so you don’t calibrate one system while missing another.
Run a Pre-Scan and Baseline Checks: DTCs, Warning Lights, and Prerequisites
A reliable way to validate OEM ADAS Calibration needs on Ford Ranger Raptor is to treat the pre-scan and baseline checks as mandatory. Perform a comprehensive pre-scan of ADAS modules and record active and stored DTCs, calibration-required indicators, and status fields showing incomplete learning. Many vehicles request calibration without a constant dash light, so scan output is the confirmation layer; save it for the VIN. Next, verify prerequisites that impact accuracy: correct tire pressure, matched tire size, normal ride height, and stable battery voltage so module communication stays solid. Inspect the camera viewing path: clean the glass at the camera window, confirm the housing is seated, and remove tint edges, adhesives, trim, or accessories that obstruct the field of view. For radar-equipped Ford Ranger Raptor variants, inspect brackets and covers for bends, misalignment, or loose fasteners; calibration will not correct a distorted mount. If recent alignment or suspension work occurred, confirm alignment angles are in spec and steering angle readings make sense. For static ADAS Calibration, confirm your setup can meet OEM conditions (level floor, target placement, lighting control) before starting. This gate prevents repeated failures and reduces unstable alerts after delivery.
Choose the Correct Method: Static vs Dynamic Calibration vs Initialization for Ford Ranger Raptor
Choosing the OEM method for ADAS Calibration on Ford Ranger Raptor is a decision step, not a preference. The procedure may require static calibration, dynamic calibration, a combined sequence, or an initialization/relearn routine, depending on the sensor package and the trigger event. Static ADAS Calibration uses targets and measurements to validate geometry in a controlled space, so it is sensitive to target distance and height, centerline references, lighting, and floor level. Dynamic ADAS Calibration relies on an OEM-defined drive cycle, so it is sensitive to speed window, lane-marking quality, traffic, and weather. Some Ford Ranger Raptor variants require both methods in sequence, and changing the order can leave modules incomplete. Initialization may be required after certain resets (for example, steering angle or yaw-rate relearn), but it does not replace calibration when the OEM calls for it after windshield or bracket disturbance. Use scan evidence and VIN-applicable service information to decide: if DTCs indicate calibration required, follow the routine tied to those codes. Do not start static without the correct target setup, and do not start dynamic if you cannot safely meet the drive requirements. Fix mounting or geometry issues first; calibration cannot compensate for a bent bracket or mis-seated camera.
Verify and Document: Post-Scan Reports, Results, and Proof for Ford Ranger Raptor
For OEM-calibrated ADAS work on your Ford Ranger Raptor, verify and document results before delivery. Start with a post-repair diagnostic scan to confirm DTCs are resolved, warning lights are off, modules communicate, and no new faults were introduced. If calibration was performed, documentation should list the systems addressed (forward camera, radar, lane keep assist, forward collision warning, automatic emergency braking, blind spot monitoring), the method used (static, dynamic, dual, or initialization), and the completion status. Many providers supply a scan report and calibration certificate that ties results to the VIN and timestamps. This proof supports comprehensive insurance claims, reduces delays, and creates a defensible record if questions arise. It also helps future troubleshooting when intermittent alerts appear later, because before-and-after scans establish a baseline. At Bang AutoGlass, we can advise what reports to request and help coordinate scanning and recalibration when required. Pair that with next-day mobile service, a typical 30-45 minute replacement, at least one hour safe drive cure time, acceptance of comprehensive insurance coverage, and a lifetime workmanship warranty. Keep these reports with your invoice for future reference and resale value.
Services
Service Areas
OEM Calibration Requirements for Ford Ranger Raptor: How to Confirm What Must Be Calibrated
Start With VIN-Specific ADAS Feature Identification for Ford Ranger Raptor
OEM ADAS Calibration requirements for a Ford Ranger Raptor are only reliable when you start from a VIN-verified ADAS configuration. ADAS content is option-driven, so two Ford Ranger Raptor vehicles can have different camera or radar packages even if they share the same appearance. Decode the VIN, confirm option codes, and list the driver-assist features present: lane keeping or centering, adaptive cruise, forward collision warning, automatic emergency braking, traffic sign recognition, blind-spot monitoring and rear cross-traffic alerts, and any parking or surround-view features. Next, connect features to hardware by confirming sensor locations and the modules that process them. For many Ford Ranger Raptor setups, that means a forward camera behind the windshield and radar sensors in the grille or bumper area, plus any corner sensors used for cross-traffic logic. Note supporting sensors the OEM may treat as prerequisites (steering angle, yaw rate, ride-height). Document the configuration in a short VIN record: features present, sensors and modules present, and mounting locations. With that foundation, decisions about static calibration, dynamic calibration, sequencing, and proof are tied to the exact Ford Ranger Raptor you serviced, not assumptions that can lead to intermittent warnings later. This inventory clarifies which repairs can disturb geometry and which modules must be validated.
Find the OEM Source of Truth: Service Info, Bulletins, and Position Statements
After you confirm which ADAS features your Ford Ranger Raptor has, verify calibration requirements from the manufacturer—not from generic charts. OEM requirements typically live in official service information (factory manuals and diagnostic routines), Technical Service Bulletins (TSBs) that update triggers or prerequisites, and OEM position statements that outline expectations for safe, compliant repairs. When confirming what must be calibrated, prioritize what the OEM publishes for the correct model year and VIN-level equipment. Position statements are especially useful for windshield and camera work because they address common scenarios: proper camera mounting, use of OEM-spec glass, pre-scan and post-scan guidance, and when calibration is mandatory. Many OEM documents directly connect windshield replacement to the performance of automatic emergency braking, lane keep assist, forward collision warning, and adaptive cruise control. Industry reference tools can help you find likely requirements faster, but treat them as a starting point—the OEM procedure is the authority for an OEM-compliant plan. To stay OEM-correct, confirm you are using the latest revision and document what you referenced. That record supports liability protection, customer confidence, and insurance approvals. Bang AutoGlass keeps scheduling simple with next-day mobile service, and we can work with any insurance company if you have comprehensive coverage.
Map Calibration Triggers on Ford Ranger Raptor: What Repairs Commonly Require Recalibration
A trigger map is a fast way to confirm what must be calibrated on a Ford Ranger Raptor for OEM ADAS Calibration. Start with windshield-related events: if the forward camera mounts behind the glass, windshield replacement commonly requires calibration because camera seating, bracket alignment, and the camera-to-glass relationship define the optical axis. Any bracket replacement, re-bond, or movement is a direct trigger when the OEM specifies ADAS Calibration. Next, evaluate front-end work. Radar sensors and brackets in the grille or bumper area can be disturbed during collision repairs, bumper removal, grille replacement, or bracket service, and recalibration may be required even if no warning light is present. Add geometry triggers: wheel alignment changes, toe/camber adjustments, suspension repairs, ride-height changes, or tire-size changes can alter how the Ford Ranger Raptor interprets lane position and relative motion. Include sensor movement as a trigger even when a sensor is not replaced; small shifts can skew distance or lane calculations while communication checks still pass. Finally, identify module-specific initialization triggers (steering-angle relearn, yaw-rate reset, battery disconnect effects) that may require a relearn routine instead of full calibration, depending on OEM rules. Document the map as repair event → mount disturbed → module affected → required method so you don’t calibrate one system while missing another.
Run a Pre-Scan and Baseline Checks: DTCs, Warning Lights, and Prerequisites
A reliable way to validate OEM ADAS Calibration needs on Ford Ranger Raptor is to treat the pre-scan and baseline checks as mandatory. Perform a comprehensive pre-scan of ADAS modules and record active and stored DTCs, calibration-required indicators, and status fields showing incomplete learning. Many vehicles request calibration without a constant dash light, so scan output is the confirmation layer; save it for the VIN. Next, verify prerequisites that impact accuracy: correct tire pressure, matched tire size, normal ride height, and stable battery voltage so module communication stays solid. Inspect the camera viewing path: clean the glass at the camera window, confirm the housing is seated, and remove tint edges, adhesives, trim, or accessories that obstruct the field of view. For radar-equipped Ford Ranger Raptor variants, inspect brackets and covers for bends, misalignment, or loose fasteners; calibration will not correct a distorted mount. If recent alignment or suspension work occurred, confirm alignment angles are in spec and steering angle readings make sense. For static ADAS Calibration, confirm your setup can meet OEM conditions (level floor, target placement, lighting control) before starting. This gate prevents repeated failures and reduces unstable alerts after delivery.
Choose the Correct Method: Static vs Dynamic Calibration vs Initialization for Ford Ranger Raptor
Choosing the OEM method for ADAS Calibration on Ford Ranger Raptor is a decision step, not a preference. The procedure may require static calibration, dynamic calibration, a combined sequence, or an initialization/relearn routine, depending on the sensor package and the trigger event. Static ADAS Calibration uses targets and measurements to validate geometry in a controlled space, so it is sensitive to target distance and height, centerline references, lighting, and floor level. Dynamic ADAS Calibration relies on an OEM-defined drive cycle, so it is sensitive to speed window, lane-marking quality, traffic, and weather. Some Ford Ranger Raptor variants require both methods in sequence, and changing the order can leave modules incomplete. Initialization may be required after certain resets (for example, steering angle or yaw-rate relearn), but it does not replace calibration when the OEM calls for it after windshield or bracket disturbance. Use scan evidence and VIN-applicable service information to decide: if DTCs indicate calibration required, follow the routine tied to those codes. Do not start static without the correct target setup, and do not start dynamic if you cannot safely meet the drive requirements. Fix mounting or geometry issues first; calibration cannot compensate for a bent bracket or mis-seated camera.
Verify and Document: Post-Scan Reports, Results, and Proof for Ford Ranger Raptor
For OEM-calibrated ADAS work on your Ford Ranger Raptor, verify and document results before delivery. Start with a post-repair diagnostic scan to confirm DTCs are resolved, warning lights are off, modules communicate, and no new faults were introduced. If calibration was performed, documentation should list the systems addressed (forward camera, radar, lane keep assist, forward collision warning, automatic emergency braking, blind spot monitoring), the method used (static, dynamic, dual, or initialization), and the completion status. Many providers supply a scan report and calibration certificate that ties results to the VIN and timestamps. This proof supports comprehensive insurance claims, reduces delays, and creates a defensible record if questions arise. It also helps future troubleshooting when intermittent alerts appear later, because before-and-after scans establish a baseline. At Bang AutoGlass, we can advise what reports to request and help coordinate scanning and recalibration when required. Pair that with next-day mobile service, a typical 30-45 minute replacement, at least one hour safe drive cure time, acceptance of comprehensive insurance coverage, and a lifetime workmanship warranty. Keep these reports with your invoice for future reference and resale value.
Enjoy More Relevant Blogs
Tempered vs Laminated Door Glass on Dodge Ram 2500 Regular Cab: What’s Used and Why It Matters
Tempered vs laminated door glass on Dodge Ram 2500 Regular Cab: what your vehicle uses, how it breaks, and what it means for replacement safety, cost, and cleanup.
How to Schedule ADAS Calibration for Ford F250 Super Duty Crew Cab After Windshield Replacement
Schedule ADAS calibration for Ford F250 Super Duty Crew Cab after windshield replacement. Learn timing, required info, and what to expect so safety systems stay accurate.
After a Break-In: Dodge Challenger Quarter Glass Replacement Plan to Restore Security and Visibility
After a break-in on Dodge Challenger, restore security with a quarter glass replacement plan: cleanup, temporary protection, scheduling, and post-install checks.
Will Insurance Cover Door Glass Replacement for a Ford Focus RS? Claims Steps, Deductibles, and What to Document
Will insurance cover Ford Focus RS door glass replacement? Learn claim steps, deductibles, photos to document, and how to schedule fast repairs today.
ADAS After Windshield Replacement on Gmc Terrain: Calibration Basics and Safety Checks
ADAS after Gmc Terrain windshield replacement: calibration basics, common safety checks, and how to confirm cameras and sensors are working correctly.
How to Schedule Mobile Rear Glass Replacement for Gmc Rally Wagon 2500
Schedule mobile rear glass replacement for your Gmc Rally Wagon 2500 in minutes. Learn what info to provide, how long it takes, and prep tips for service day.
Stop Leaks and Wind Noise: What Proper Dodge Durango Quarter Glass Replacement Should Prevent
Stop leaks and wind noise with proper Dodge Durango quarter glass replacement. Learn what correct fit, sealing, and trim should prevent after install.
Tempered Safety Rear Glass Replacement for Gmc Canyon Crew Cab: Understanding DOT Markings and FMVSS 205
Need Gmc Canyon Crew Cab rear glass replacement? Learn tempered safety glass basics, DOT markings, and FMVSS 205, plus install and cure tips. Get a quote today.
Post-Install Checks for Gmc Sierra (Classic) 1500 Extended Cab: Rear Glass Replacement Wind Noise, Leaks, and Rattle Tests
Post-install rear glass checks for Gmc Sierra (Classic) 1500 Extended Cab: test for wind noise, leaks, and rattles, plus when to return for warranty service—check today before trips.
Fast Scheduling Guide: Gmc Sierra 3500 Hd Extended Cab Windshield Replacement From Booking to Install
Book Gmc Sierra 3500 Hd Extended Cab windshield replacement fast. See scheduling steps, what to prep, install timing, and when you can safely drive away. Get a quote today.
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm