Services
Service Areas
Stop Leaks and Wind Noise: What Proper Gmc 3500 Extended Cab Quarter Glass Replacement Should Prevent
Leak and Wind Noise Root Causes on Gmc 3500 Extended Cab: Where Bad Sealing Shows Up First
After a Gmc 3500 Extended Cab quarter glass replacement (rear quarter window replacement), leaks and wind noise almost always trace back to the seal and bond line—not a “mystery.” The first trouble spots are the outer edges where the fixed rear quarter glass meets the body at the C-pillar, roofline, and beltline. A tiny air gap can whistle or howl at highway speed, while a narrow water path can run behind quarter trim, dampen the headliner, or collect in the rear cargo area or trunk. Common causes are predictable: the wrong-fit quarter glass or molding profile, old urethane that was not close-cut evenly, skipped primer/activator steps, or contamination from fingerprints, dust, wash chemicals, or silicone dressings. Even if the adhesive is strong, trim that is not fully seated can lift in airflow and amplify noise. Hidden pinchweld corrosion can also weaken the bond over time and reopen leak paths. Bang AutoGlass prevents these issues at the source with mobile Gmc 3500 Extended Cab quarter glass replacement and auto glass repair, typically completed in 30-45 minutes. We recommend at least one hour of safe drive-away time for the adhesive to set. Every installation is backed by a lifetime workmanship warranty, and we work with all insurance companies when comprehensive coverage applies.
Correct Quarter Glass Verification: Body Location, Tint/Privacy, and DOT/FMVSS 205 Markings
Proper Gmc 3500 Extended Cab quarter glass verification should be done before any adhesive is opened. A technician confirms the exact position (left or right rear quarter, fixed side glass) and matches the part to your model year and trim, since small dimensional differences change how the molding seats and how the edge frit band seals. Tint and privacy level must also match—mismatched shading is obvious and can alter the molding-to-glass interface. If your Gmc 3500 Extended Cab includes privacy tint, acoustic glass, or an integrated antenna in the quarter area, those features should be confirmed up front. Next, check the safety-glazing markings. In the U.S., quarter glass typically carries “DOT” plus a manufacturer code assigned by NHTSA and an “AS” classification under ANSI/SAE Z26.1 as referenced by FMVSS 205. Side and rear positions commonly show AS2; some darker privacy glass may be marked AS3, while windshields are usually AS1. Bang AutoGlass performs this verification on-site with our mobile service so the right Gmc 3500 Extended Cab rear quarter window replacement arrives the first time. We can often schedule next day and support insurance claims across all carriers when comprehensive coverage applies.
Pinchweld and Bond Prep Checklist: Corrosion Control, Cleaning, and Primer/Activator Steps
Most quarter window leaks start with rushed bond prep. For a Gmc 3500 Extended Cab quarter glass replacement, the pinchweld must be clean, corrosion-free, and compatible with the urethane system. The workflow should protect interior panels, remove trim and moldings without damaging clips, cut out the old rear quarter glass, and remove every shard and dust particle. Debris in the bond zone creates voids and weakens the seal, especially at tight corners. Old urethane should be close-cut and left as a thin, continuous base (about 1-2 mm). That base gives the fresh bead a stable surface to bond to and helps keep consistent glass height. If bare metal is exposed, treat it immediately: clean, address corrosion, and apply the correct primer so rust cannot creep under the adhesive. Final prep is about sequence and timing: clean and dry the bonding area, apply activator and primer in the manufacturer’s order, use clean applicators and gloves, and allow proper flash time. Bang AutoGlass follows a repeatable pinchweld prep checklist for every mobile Gmc 3500 Extended Cab rear quarter window replacement. Most jobs take 30-45 minutes, we recommend at least one hour of safe drive-away time, and every install is backed by a lifetime workmanship warranty.
Adhesive Bead and Set-In Accuracy: Alignment, Edge Support, and Minimum Drive-Away Time
Repeat wind noise after a Gmc 3500 Extended Cab quarter glass replacement usually points to uneven urethane coverage or a small alignment error. Because the quarter window is fixed, the urethane bead must seal and support the panel around the full perimeter. Start with a dry-fit, confirm the reveal line, and add simple guide marks at the roofline, C-pillar, and beltline. Then lay a continuous triangular bead with consistent height and width. If the bead is too low, compressed unevenly, or interrupted at a corner, you can end up with an air pocket, a leak path, or a stress point that later breaks the seal. Set-in should be deliberate. Use setting blocks or clips where the design calls for them, then press the glass into wet urethane with even pressure so compression stays consistent. A minor tilt at the C-pillar can lift the molding and create a whistle that only shows up at steady highway speeds. After seating, confirm the panel is flush and backfill any edge gaps so no voids remain. Drive-away time matters too. Follow the adhesive manufacturer’s current cure-time specs. Bang AutoGlass typically completes mobile service in 30-45 minutes and recommends at least one hour before driving your Gmc 3500 Extended Cab.
Seal, Trim, and Molding Fit: Preventing Whistles, Air Gaps, and Water Intrusion
A Gmc 3500 Extended Cab quarter glass replacement isn’t finished when the glass is bonded; it’s finished when the perimeter is water-tight again. Reveal moldings and surrounding trim stabilize the edge, shield the urethane, and prevent airflow from grabbing the glass-to-body seam. When wind noise appears after repair, the cause is often a partially lifted molding, a clip that didn’t fully engage, or trim that is warped, missing, or routed incorrectly. Those small defects can whistle at 60+ mph and can also let water travel behind interior quarter panels. Verification should be more than a quick glance. Check that the molding sits flush at the roofline, C-pillar, and beltline with consistent compression and no gaps at transitions. The reveal line should be even, and the trim should not pinch the glass or pull it out of plane. On press-in moldings or encapsulated edges, confirm the molding-to-urethane interface is continuous so it won’t lift under airflow or after temperature swings. Also inspect for exposed urethane or uneven seams that collect dirt and compromise sealing. Bang AutoGlass includes this perimeter fit check in our mobile Gmc 3500 Extended Cab quarter glass replacement process, and we back our work with a lifetime workmanship warranty.
Post-Install Proof: Water Test, Road Test, and Documentation for Gmc 3500 Extended Cab Quarter Glass
A quality Gmc 3500 Extended Cab quarter glass replacement should be verified, not assumed. The best installers close the loop with objective checks that confirm sealing, trim fit, and wind-noise performance before the job is considered complete. Start with a controlled water test. Use a gentle, steady stream along the roofline, C-pillar, and beltline perimeter instead of a high-pressure nozzle that can force water past seals. While water runs, inspect inside for seepage near the headliner edge, behind the quarter trim, and in the rear cargo area or trunk. This helps spot trim channeling and micro-gaps at corners. Next, road test at consistent speeds and listen for whistling, flutter, or buffeting around the quarter window area. After the drive, inspect the perimeter again to confirm the molding remained fully seated and the glass stayed flush with uniform gaps. If your Gmc 3500 Extended Cab has privacy tint, acoustic glazing, or a quarter-area antenna element, verify alignment and function before closeout. Finally, documentation protects you. Notes and photos support warranty coverage and make insurance claims easier when comprehensive coverage applies. Bang AutoGlass backs workmanship with a lifetime warranty, offers mobile service often as soon as next day, and recommends at least one hour of safe drive-away time after installation.
Services
Service Areas
Stop Leaks and Wind Noise: What Proper Gmc 3500 Extended Cab Quarter Glass Replacement Should Prevent
Leak and Wind Noise Root Causes on Gmc 3500 Extended Cab: Where Bad Sealing Shows Up First
After a Gmc 3500 Extended Cab quarter glass replacement (rear quarter window replacement), leaks and wind noise almost always trace back to the seal and bond line—not a “mystery.” The first trouble spots are the outer edges where the fixed rear quarter glass meets the body at the C-pillar, roofline, and beltline. A tiny air gap can whistle or howl at highway speed, while a narrow water path can run behind quarter trim, dampen the headliner, or collect in the rear cargo area or trunk. Common causes are predictable: the wrong-fit quarter glass or molding profile, old urethane that was not close-cut evenly, skipped primer/activator steps, or contamination from fingerprints, dust, wash chemicals, or silicone dressings. Even if the adhesive is strong, trim that is not fully seated can lift in airflow and amplify noise. Hidden pinchweld corrosion can also weaken the bond over time and reopen leak paths. Bang AutoGlass prevents these issues at the source with mobile Gmc 3500 Extended Cab quarter glass replacement and auto glass repair, typically completed in 30-45 minutes. We recommend at least one hour of safe drive-away time for the adhesive to set. Every installation is backed by a lifetime workmanship warranty, and we work with all insurance companies when comprehensive coverage applies.
Correct Quarter Glass Verification: Body Location, Tint/Privacy, and DOT/FMVSS 205 Markings
Proper Gmc 3500 Extended Cab quarter glass verification should be done before any adhesive is opened. A technician confirms the exact position (left or right rear quarter, fixed side glass) and matches the part to your model year and trim, since small dimensional differences change how the molding seats and how the edge frit band seals. Tint and privacy level must also match—mismatched shading is obvious and can alter the molding-to-glass interface. If your Gmc 3500 Extended Cab includes privacy tint, acoustic glass, or an integrated antenna in the quarter area, those features should be confirmed up front. Next, check the safety-glazing markings. In the U.S., quarter glass typically carries “DOT” plus a manufacturer code assigned by NHTSA and an “AS” classification under ANSI/SAE Z26.1 as referenced by FMVSS 205. Side and rear positions commonly show AS2; some darker privacy glass may be marked AS3, while windshields are usually AS1. Bang AutoGlass performs this verification on-site with our mobile service so the right Gmc 3500 Extended Cab rear quarter window replacement arrives the first time. We can often schedule next day and support insurance claims across all carriers when comprehensive coverage applies.
Pinchweld and Bond Prep Checklist: Corrosion Control, Cleaning, and Primer/Activator Steps
Most quarter window leaks start with rushed bond prep. For a Gmc 3500 Extended Cab quarter glass replacement, the pinchweld must be clean, corrosion-free, and compatible with the urethane system. The workflow should protect interior panels, remove trim and moldings without damaging clips, cut out the old rear quarter glass, and remove every shard and dust particle. Debris in the bond zone creates voids and weakens the seal, especially at tight corners. Old urethane should be close-cut and left as a thin, continuous base (about 1-2 mm). That base gives the fresh bead a stable surface to bond to and helps keep consistent glass height. If bare metal is exposed, treat it immediately: clean, address corrosion, and apply the correct primer so rust cannot creep under the adhesive. Final prep is about sequence and timing: clean and dry the bonding area, apply activator and primer in the manufacturer’s order, use clean applicators and gloves, and allow proper flash time. Bang AutoGlass follows a repeatable pinchweld prep checklist for every mobile Gmc 3500 Extended Cab rear quarter window replacement. Most jobs take 30-45 minutes, we recommend at least one hour of safe drive-away time, and every install is backed by a lifetime workmanship warranty.
Adhesive Bead and Set-In Accuracy: Alignment, Edge Support, and Minimum Drive-Away Time
Repeat wind noise after a Gmc 3500 Extended Cab quarter glass replacement usually points to uneven urethane coverage or a small alignment error. Because the quarter window is fixed, the urethane bead must seal and support the panel around the full perimeter. Start with a dry-fit, confirm the reveal line, and add simple guide marks at the roofline, C-pillar, and beltline. Then lay a continuous triangular bead with consistent height and width. If the bead is too low, compressed unevenly, or interrupted at a corner, you can end up with an air pocket, a leak path, or a stress point that later breaks the seal. Set-in should be deliberate. Use setting blocks or clips where the design calls for them, then press the glass into wet urethane with even pressure so compression stays consistent. A minor tilt at the C-pillar can lift the molding and create a whistle that only shows up at steady highway speeds. After seating, confirm the panel is flush and backfill any edge gaps so no voids remain. Drive-away time matters too. Follow the adhesive manufacturer’s current cure-time specs. Bang AutoGlass typically completes mobile service in 30-45 minutes and recommends at least one hour before driving your Gmc 3500 Extended Cab.
Seal, Trim, and Molding Fit: Preventing Whistles, Air Gaps, and Water Intrusion
A Gmc 3500 Extended Cab quarter glass replacement isn’t finished when the glass is bonded; it’s finished when the perimeter is water-tight again. Reveal moldings and surrounding trim stabilize the edge, shield the urethane, and prevent airflow from grabbing the glass-to-body seam. When wind noise appears after repair, the cause is often a partially lifted molding, a clip that didn’t fully engage, or trim that is warped, missing, or routed incorrectly. Those small defects can whistle at 60+ mph and can also let water travel behind interior quarter panels. Verification should be more than a quick glance. Check that the molding sits flush at the roofline, C-pillar, and beltline with consistent compression and no gaps at transitions. The reveal line should be even, and the trim should not pinch the glass or pull it out of plane. On press-in moldings or encapsulated edges, confirm the molding-to-urethane interface is continuous so it won’t lift under airflow or after temperature swings. Also inspect for exposed urethane or uneven seams that collect dirt and compromise sealing. Bang AutoGlass includes this perimeter fit check in our mobile Gmc 3500 Extended Cab quarter glass replacement process, and we back our work with a lifetime workmanship warranty.
Post-Install Proof: Water Test, Road Test, and Documentation for Gmc 3500 Extended Cab Quarter Glass
A quality Gmc 3500 Extended Cab quarter glass replacement should be verified, not assumed. The best installers close the loop with objective checks that confirm sealing, trim fit, and wind-noise performance before the job is considered complete. Start with a controlled water test. Use a gentle, steady stream along the roofline, C-pillar, and beltline perimeter instead of a high-pressure nozzle that can force water past seals. While water runs, inspect inside for seepage near the headliner edge, behind the quarter trim, and in the rear cargo area or trunk. This helps spot trim channeling and micro-gaps at corners. Next, road test at consistent speeds and listen for whistling, flutter, or buffeting around the quarter window area. After the drive, inspect the perimeter again to confirm the molding remained fully seated and the glass stayed flush with uniform gaps. If your Gmc 3500 Extended Cab has privacy tint, acoustic glazing, or a quarter-area antenna element, verify alignment and function before closeout. Finally, documentation protects you. Notes and photos support warranty coverage and make insurance claims easier when comprehensive coverage applies. Bang AutoGlass backs workmanship with a lifetime warranty, offers mobile service often as soon as next day, and recommends at least one hour of safe drive-away time after installation.
Services
Service Areas
Stop Leaks and Wind Noise: What Proper Gmc 3500 Extended Cab Quarter Glass Replacement Should Prevent
Leak and Wind Noise Root Causes on Gmc 3500 Extended Cab: Where Bad Sealing Shows Up First
After a Gmc 3500 Extended Cab quarter glass replacement (rear quarter window replacement), leaks and wind noise almost always trace back to the seal and bond line—not a “mystery.” The first trouble spots are the outer edges where the fixed rear quarter glass meets the body at the C-pillar, roofline, and beltline. A tiny air gap can whistle or howl at highway speed, while a narrow water path can run behind quarter trim, dampen the headliner, or collect in the rear cargo area or trunk. Common causes are predictable: the wrong-fit quarter glass or molding profile, old urethane that was not close-cut evenly, skipped primer/activator steps, or contamination from fingerprints, dust, wash chemicals, or silicone dressings. Even if the adhesive is strong, trim that is not fully seated can lift in airflow and amplify noise. Hidden pinchweld corrosion can also weaken the bond over time and reopen leak paths. Bang AutoGlass prevents these issues at the source with mobile Gmc 3500 Extended Cab quarter glass replacement and auto glass repair, typically completed in 30-45 minutes. We recommend at least one hour of safe drive-away time for the adhesive to set. Every installation is backed by a lifetime workmanship warranty, and we work with all insurance companies when comprehensive coverage applies.
Correct Quarter Glass Verification: Body Location, Tint/Privacy, and DOT/FMVSS 205 Markings
Proper Gmc 3500 Extended Cab quarter glass verification should be done before any adhesive is opened. A technician confirms the exact position (left or right rear quarter, fixed side glass) and matches the part to your model year and trim, since small dimensional differences change how the molding seats and how the edge frit band seals. Tint and privacy level must also match—mismatched shading is obvious and can alter the molding-to-glass interface. If your Gmc 3500 Extended Cab includes privacy tint, acoustic glass, or an integrated antenna in the quarter area, those features should be confirmed up front. Next, check the safety-glazing markings. In the U.S., quarter glass typically carries “DOT” plus a manufacturer code assigned by NHTSA and an “AS” classification under ANSI/SAE Z26.1 as referenced by FMVSS 205. Side and rear positions commonly show AS2; some darker privacy glass may be marked AS3, while windshields are usually AS1. Bang AutoGlass performs this verification on-site with our mobile service so the right Gmc 3500 Extended Cab rear quarter window replacement arrives the first time. We can often schedule next day and support insurance claims across all carriers when comprehensive coverage applies.
Pinchweld and Bond Prep Checklist: Corrosion Control, Cleaning, and Primer/Activator Steps
Most quarter window leaks start with rushed bond prep. For a Gmc 3500 Extended Cab quarter glass replacement, the pinchweld must be clean, corrosion-free, and compatible with the urethane system. The workflow should protect interior panels, remove trim and moldings without damaging clips, cut out the old rear quarter glass, and remove every shard and dust particle. Debris in the bond zone creates voids and weakens the seal, especially at tight corners. Old urethane should be close-cut and left as a thin, continuous base (about 1-2 mm). That base gives the fresh bead a stable surface to bond to and helps keep consistent glass height. If bare metal is exposed, treat it immediately: clean, address corrosion, and apply the correct primer so rust cannot creep under the adhesive. Final prep is about sequence and timing: clean and dry the bonding area, apply activator and primer in the manufacturer’s order, use clean applicators and gloves, and allow proper flash time. Bang AutoGlass follows a repeatable pinchweld prep checklist for every mobile Gmc 3500 Extended Cab rear quarter window replacement. Most jobs take 30-45 minutes, we recommend at least one hour of safe drive-away time, and every install is backed by a lifetime workmanship warranty.
Adhesive Bead and Set-In Accuracy: Alignment, Edge Support, and Minimum Drive-Away Time
Repeat wind noise after a Gmc 3500 Extended Cab quarter glass replacement usually points to uneven urethane coverage or a small alignment error. Because the quarter window is fixed, the urethane bead must seal and support the panel around the full perimeter. Start with a dry-fit, confirm the reveal line, and add simple guide marks at the roofline, C-pillar, and beltline. Then lay a continuous triangular bead with consistent height and width. If the bead is too low, compressed unevenly, or interrupted at a corner, you can end up with an air pocket, a leak path, or a stress point that later breaks the seal. Set-in should be deliberate. Use setting blocks or clips where the design calls for them, then press the glass into wet urethane with even pressure so compression stays consistent. A minor tilt at the C-pillar can lift the molding and create a whistle that only shows up at steady highway speeds. After seating, confirm the panel is flush and backfill any edge gaps so no voids remain. Drive-away time matters too. Follow the adhesive manufacturer’s current cure-time specs. Bang AutoGlass typically completes mobile service in 30-45 minutes and recommends at least one hour before driving your Gmc 3500 Extended Cab.
Seal, Trim, and Molding Fit: Preventing Whistles, Air Gaps, and Water Intrusion
A Gmc 3500 Extended Cab quarter glass replacement isn’t finished when the glass is bonded; it’s finished when the perimeter is water-tight again. Reveal moldings and surrounding trim stabilize the edge, shield the urethane, and prevent airflow from grabbing the glass-to-body seam. When wind noise appears after repair, the cause is often a partially lifted molding, a clip that didn’t fully engage, or trim that is warped, missing, or routed incorrectly. Those small defects can whistle at 60+ mph and can also let water travel behind interior quarter panels. Verification should be more than a quick glance. Check that the molding sits flush at the roofline, C-pillar, and beltline with consistent compression and no gaps at transitions. The reveal line should be even, and the trim should not pinch the glass or pull it out of plane. On press-in moldings or encapsulated edges, confirm the molding-to-urethane interface is continuous so it won’t lift under airflow or after temperature swings. Also inspect for exposed urethane or uneven seams that collect dirt and compromise sealing. Bang AutoGlass includes this perimeter fit check in our mobile Gmc 3500 Extended Cab quarter glass replacement process, and we back our work with a lifetime workmanship warranty.
Post-Install Proof: Water Test, Road Test, and Documentation for Gmc 3500 Extended Cab Quarter Glass
A quality Gmc 3500 Extended Cab quarter glass replacement should be verified, not assumed. The best installers close the loop with objective checks that confirm sealing, trim fit, and wind-noise performance before the job is considered complete. Start with a controlled water test. Use a gentle, steady stream along the roofline, C-pillar, and beltline perimeter instead of a high-pressure nozzle that can force water past seals. While water runs, inspect inside for seepage near the headliner edge, behind the quarter trim, and in the rear cargo area or trunk. This helps spot trim channeling and micro-gaps at corners. Next, road test at consistent speeds and listen for whistling, flutter, or buffeting around the quarter window area. After the drive, inspect the perimeter again to confirm the molding remained fully seated and the glass stayed flush with uniform gaps. If your Gmc 3500 Extended Cab has privacy tint, acoustic glazing, or a quarter-area antenna element, verify alignment and function before closeout. Finally, documentation protects you. Notes and photos support warranty coverage and make insurance claims easier when comprehensive coverage applies. Bang AutoGlass backs workmanship with a lifetime warranty, offers mobile service often as soon as next day, and recommends at least one hour of safe drive-away time after installation.
Enjoy More Relevant Blogs
Tempered vs Laminated Door Glass on Dodge Ram 2500 Regular Cab: What’s Used and Why It Matters
Tempered vs laminated door glass on Dodge Ram 2500 Regular Cab: what your vehicle uses, how it breaks, and what it means for replacement safety, cost, and cleanup.
How to Schedule ADAS Calibration for Ford F250 Super Duty Crew Cab After Windshield Replacement
Schedule ADAS calibration for Ford F250 Super Duty Crew Cab after windshield replacement. Learn timing, required info, and what to expect so safety systems stay accurate.
After a Break-In: Dodge Challenger Quarter Glass Replacement Plan to Restore Security and Visibility
After a break-in on Dodge Challenger, restore security with a quarter glass replacement plan: cleanup, temporary protection, scheduling, and post-install checks.
Will Insurance Cover Door Glass Replacement for a Ford Focus RS? Claims Steps, Deductibles, and What to Document
Will insurance cover Ford Focus RS door glass replacement? Learn claim steps, deductibles, photos to document, and how to schedule fast repairs today.
ADAS After Windshield Replacement on Gmc Terrain: Calibration Basics and Safety Checks
ADAS after Gmc Terrain windshield replacement: calibration basics, common safety checks, and how to confirm cameras and sensors are working correctly.
How to Schedule Mobile Rear Glass Replacement for Gmc Rally Wagon 2500
Schedule mobile rear glass replacement for your Gmc Rally Wagon 2500 in minutes. Learn what info to provide, how long it takes, and prep tips for service day.
Stop Leaks and Wind Noise: What Proper Dodge Durango Quarter Glass Replacement Should Prevent
Stop leaks and wind noise with proper Dodge Durango quarter glass replacement. Learn what correct fit, sealing, and trim should prevent after install.
Tempered Safety Rear Glass Replacement for Gmc Canyon Crew Cab: Understanding DOT Markings and FMVSS 205
Need Gmc Canyon Crew Cab rear glass replacement? Learn tempered safety glass basics, DOT markings, and FMVSS 205, plus install and cure tips. Get a quote today.
Post-Install Checks for Gmc Sierra (Classic) 1500 Extended Cab: Rear Glass Replacement Wind Noise, Leaks, and Rattle Tests
Post-install rear glass checks for Gmc Sierra (Classic) 1500 Extended Cab: test for wind noise, leaks, and rattles, plus when to return for warranty service—check today before trips.
Fast Scheduling Guide: Gmc Sierra 3500 Hd Extended Cab Windshield Replacement From Booking to Install
Book Gmc Sierra 3500 Hd Extended Cab windshield replacement fast. See scheduling steps, what to prep, install timing, and when you can safely drive away. Get a quote today.
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm