Services
Service Areas
Pre- and Post-Calibration Scans for Gmc Sierra 1500 Extended Cab: Proving Systems Are Set Correctly
Scanning vs Calibration on Gmc Sierra 1500 Extended Cab: What Each Step Proves
For your Gmc Sierra 1500 Extended Cab, a scan and a calibration are not interchangeable, even when both are part of the same visit. A diagnostic scan queries the vehicle computers and reports DTCs, communication faults, and system status. It answers what the Gmc Sierra 1500 Extended Cab is reporting right now and creates a baseline you can compare before and after repair. Calibration is the OEM accuracy procedure for ADAS. It validates camera and sensor alignment so the system interprets lane markings, distance, and objects within specification. Depending on the Gmc Sierra 1500 Extended Cab, calibration may be a static target setup, a defined dynamic drive, or both. A scan can be clean while a sensor is still outside tolerance, which can change how lane keep assist, forward collision warning, adaptive cruise control, and automatic emergency braking behave after windshield replacement. Bang AutoGlass treats this as verification: pre-scan, perform OEM-required calibration when applicable, then post-scan to document a clean report. We provide mobile auto glass service, often as soon as next day. Most windshield replacements take 30-45 minutes plus at least one hour adhesive cure time before safe drive-away. Every job includes a lifetime workmanship warranty, and we work with any insurance carrier when comprehensive coverage applies.
Pre-Calibration Scan: Capturing DTCs, Baselines, and Calibration Triggers
Before calibrating ADAS on a Gmc Sierra 1500 Extended Cab, the pre-calibration scan is the control point. We run a full diagnostic scan to record DTCs, module communication health, and system readiness before any calibration begins. This baseline documents what existed prior to repair and gives you a report to compare with the post-scan. The scan also flags issues that can derail calibration, including low battery voltage, network faults, and unrelated stored codes. Correct these first so the calibration routine runs under stable conditions. Scan results support OEM guidance on when calibration is required for your Gmc Sierra 1500 Extended Cab. Typical triggers include windshield replacement with a forward-facing camera, camera or bracket removal, alignment or suspension changes that alter ride height, and repairs affecting sensor mounting angles. If ADAS DTCs or calibration-incomplete events are present, calibration supports lane keep assist, forward collision warning, adaptive cruise control, and automatic emergency braking. Bang AutoGlass saves the scan report, follows OEM service information for the required method, then completes a post-scan to document a clean report. We provide mobile service, often as soon as next day, with 30-45 minute glass work plus at least one hour adhesive cure time before safe drive-away.
Where to Find OEM Requirements for Gmc Sierra 1500 Extended Cab: Position Statements and Service Info
For a Gmc Sierra 1500 Extended Cab, OEM service information is the source of truth for scanning and ADAS calibration. It specifies the events that require calibration, the approved tooling, and the exact steps for static target placement and/or a required dynamic drive cycle. Many manufacturers also publish position statements that outline expectations for pre- and post-repair scanning, windshield replacement considerations, and calibration documentation. To locate requirements quickly, start at the OEM technical portal and search by year and Gmc Sierra 1500 Extended Cab. Review Driver Assistance or ADAS sections, windshield or glass procedures, and diagnostic pages tied to relevant DTCs. Industry research and lookup tools can help identify likely calibrations and prerequisites, but confirm the final procedure in OEM documentation before work is performed. If the OEM provides a position statement PDF, keep it with your scan reports and calibration records. Bang AutoGlass follows the OEM workflow and documents the requirement, the method performed, and the before/after scan results in clear, insurer-friendly language for safety, liability, and claims support. The goal is proof that your Gmc Sierra 1500 Extended Cab was scanned, calibrated when required, and verified afterward.
Set-Up Checks Before Calibration: Glass, Brackets, Tires, Ride Height, and Environment
Pre-checks before calibrating a Gmc Sierra 1500 Extended Cab aren't "extra" - they're the conditions the OEM assumes before a camera or radar calibration can be trusted. Start with the windshield and camera hardware: verify the correct windshield specification for the Gmc Sierra 1500 Extended Cab, clean the camera viewing area, and inspect the camera bracket and mounting surfaces for damage, looseness, or contamination. If the bracket is shifted, the camera sits at the wrong angle and the routine may complete with marginal accuracy. Next, restore OEM stance. Confirm tire sizes match side-to-side, set tire pressures to door-jamb spec, verify TPMS operation, and remove heavy cargo that alters ride height. If the Gmc Sierra 1500 Extended Cab was lifted/lowered or recently had steering or suspension work, complete required repairs and alignment first, then calibrate. Finally, match the environment to the method. Static calibration typically needs a level floor, precise target distances from OEM reference points, correct target type, and controlled lighting to prevent glare. Dynamic calibration may require an OEM-defined drive cycle on clearly marked roads with good visibility. At Bang AutoGlass, we coordinate mobile windshield replacement and clear prep steps so your Gmc Sierra 1500 Extended Cab meets OEM prerequisites before calibration begins.
Post-Calibration Scan and Health Check: Confirming DTCs Are Cleared and Modules Report Ready
A post-calibration scan is what turns "we ran calibration" into "the Gmc Sierra 1500 Extended Cab is verified." After completing the OEM procedure, run a full-system diagnostic post-scan to check for remaining Diagnostic Trouble Codes (DTCs), confirm modules communicate normally, and document whether ADAS-related faults cleared. Many vehicles set "calibration incomplete" or history codes during the routine, so best practice is scan -> clear applicable faults -> rescan after the procedure (and after any required ignition cycle). Verification is more than watching the dash: OEM guidance generally treats warning lights as insufficient proof of system health. Depending on the Gmc Sierra 1500 Extended Cab, confirm status flags such as calibrated/initialized/not learned, and complete any OEM-required learning or verification drive so the system reports fully ready. If the post-scan shows persistent DTCs tied to the forward camera, lane keeping, forward collision warning, adaptive cruise, blind spot monitoring, or automatic emergency braking, stop and diagnose instead of guessing. Save the scan report as the documented "after" snapshot - often expected by insurers and safety audits - so your Gmc Sierra 1500 Extended Cab leaves with evidence, not assumptions.
Documentation Package: Scan Reports, Calibration Results, and Verification Drive Notes
For a Gmc Sierra 1500 Extended Cab, a strong documentation package protects the driver, the shop, and the claim file. Industry workflows and OEM guidance emphasize: pre-scan, identify required calibrations/aiming, verify prerequisites, complete calibration, then confirm with a clean post-repair scan, because warning lights aren't a reliable substitute for documented diagnostics. Keep the packet simple and complete: a pre-calibration scan report (VIN plus all modules), the calibration result report/certificate, and a post-calibration scan showing no relevant DTCs and systems reporting ready. Add proof of process: the OEM procedure source and date, the scan/calibration platform used, and prerequisite checks (tire size uniformity, pressures at spec, ride height/levelness, alignment when required, and obstruction checks). For windshield camera work, include photos of the viewing area and camera bracket plus target setup measurements for static routines. If a dynamic routine was required, add brief verification drive notes (conditions, time/distance, and whether ADAS DTCs returned). At Bang AutoGlass, we keep this customer- and insurance-ready, offer mobile service (often next day), and back workmanship with a lifetime warranty; most windshield replacements take 30-45 minutes plus at least one hour of cure time before drive-away.
Services
Service Areas
Pre- and Post-Calibration Scans for Gmc Sierra 1500 Extended Cab: Proving Systems Are Set Correctly
Scanning vs Calibration on Gmc Sierra 1500 Extended Cab: What Each Step Proves
For your Gmc Sierra 1500 Extended Cab, a scan and a calibration are not interchangeable, even when both are part of the same visit. A diagnostic scan queries the vehicle computers and reports DTCs, communication faults, and system status. It answers what the Gmc Sierra 1500 Extended Cab is reporting right now and creates a baseline you can compare before and after repair. Calibration is the OEM accuracy procedure for ADAS. It validates camera and sensor alignment so the system interprets lane markings, distance, and objects within specification. Depending on the Gmc Sierra 1500 Extended Cab, calibration may be a static target setup, a defined dynamic drive, or both. A scan can be clean while a sensor is still outside tolerance, which can change how lane keep assist, forward collision warning, adaptive cruise control, and automatic emergency braking behave after windshield replacement. Bang AutoGlass treats this as verification: pre-scan, perform OEM-required calibration when applicable, then post-scan to document a clean report. We provide mobile auto glass service, often as soon as next day. Most windshield replacements take 30-45 minutes plus at least one hour adhesive cure time before safe drive-away. Every job includes a lifetime workmanship warranty, and we work with any insurance carrier when comprehensive coverage applies.
Pre-Calibration Scan: Capturing DTCs, Baselines, and Calibration Triggers
Before calibrating ADAS on a Gmc Sierra 1500 Extended Cab, the pre-calibration scan is the control point. We run a full diagnostic scan to record DTCs, module communication health, and system readiness before any calibration begins. This baseline documents what existed prior to repair and gives you a report to compare with the post-scan. The scan also flags issues that can derail calibration, including low battery voltage, network faults, and unrelated stored codes. Correct these first so the calibration routine runs under stable conditions. Scan results support OEM guidance on when calibration is required for your Gmc Sierra 1500 Extended Cab. Typical triggers include windshield replacement with a forward-facing camera, camera or bracket removal, alignment or suspension changes that alter ride height, and repairs affecting sensor mounting angles. If ADAS DTCs or calibration-incomplete events are present, calibration supports lane keep assist, forward collision warning, adaptive cruise control, and automatic emergency braking. Bang AutoGlass saves the scan report, follows OEM service information for the required method, then completes a post-scan to document a clean report. We provide mobile service, often as soon as next day, with 30-45 minute glass work plus at least one hour adhesive cure time before safe drive-away.
Where to Find OEM Requirements for Gmc Sierra 1500 Extended Cab: Position Statements and Service Info
For a Gmc Sierra 1500 Extended Cab, OEM service information is the source of truth for scanning and ADAS calibration. It specifies the events that require calibration, the approved tooling, and the exact steps for static target placement and/or a required dynamic drive cycle. Many manufacturers also publish position statements that outline expectations for pre- and post-repair scanning, windshield replacement considerations, and calibration documentation. To locate requirements quickly, start at the OEM technical portal and search by year and Gmc Sierra 1500 Extended Cab. Review Driver Assistance or ADAS sections, windshield or glass procedures, and diagnostic pages tied to relevant DTCs. Industry research and lookup tools can help identify likely calibrations and prerequisites, but confirm the final procedure in OEM documentation before work is performed. If the OEM provides a position statement PDF, keep it with your scan reports and calibration records. Bang AutoGlass follows the OEM workflow and documents the requirement, the method performed, and the before/after scan results in clear, insurer-friendly language for safety, liability, and claims support. The goal is proof that your Gmc Sierra 1500 Extended Cab was scanned, calibrated when required, and verified afterward.
Set-Up Checks Before Calibration: Glass, Brackets, Tires, Ride Height, and Environment
Pre-checks before calibrating a Gmc Sierra 1500 Extended Cab aren't "extra" - they're the conditions the OEM assumes before a camera or radar calibration can be trusted. Start with the windshield and camera hardware: verify the correct windshield specification for the Gmc Sierra 1500 Extended Cab, clean the camera viewing area, and inspect the camera bracket and mounting surfaces for damage, looseness, or contamination. If the bracket is shifted, the camera sits at the wrong angle and the routine may complete with marginal accuracy. Next, restore OEM stance. Confirm tire sizes match side-to-side, set tire pressures to door-jamb spec, verify TPMS operation, and remove heavy cargo that alters ride height. If the Gmc Sierra 1500 Extended Cab was lifted/lowered or recently had steering or suspension work, complete required repairs and alignment first, then calibrate. Finally, match the environment to the method. Static calibration typically needs a level floor, precise target distances from OEM reference points, correct target type, and controlled lighting to prevent glare. Dynamic calibration may require an OEM-defined drive cycle on clearly marked roads with good visibility. At Bang AutoGlass, we coordinate mobile windshield replacement and clear prep steps so your Gmc Sierra 1500 Extended Cab meets OEM prerequisites before calibration begins.
Post-Calibration Scan and Health Check: Confirming DTCs Are Cleared and Modules Report Ready
A post-calibration scan is what turns "we ran calibration" into "the Gmc Sierra 1500 Extended Cab is verified." After completing the OEM procedure, run a full-system diagnostic post-scan to check for remaining Diagnostic Trouble Codes (DTCs), confirm modules communicate normally, and document whether ADAS-related faults cleared. Many vehicles set "calibration incomplete" or history codes during the routine, so best practice is scan -> clear applicable faults -> rescan after the procedure (and after any required ignition cycle). Verification is more than watching the dash: OEM guidance generally treats warning lights as insufficient proof of system health. Depending on the Gmc Sierra 1500 Extended Cab, confirm status flags such as calibrated/initialized/not learned, and complete any OEM-required learning or verification drive so the system reports fully ready. If the post-scan shows persistent DTCs tied to the forward camera, lane keeping, forward collision warning, adaptive cruise, blind spot monitoring, or automatic emergency braking, stop and diagnose instead of guessing. Save the scan report as the documented "after" snapshot - often expected by insurers and safety audits - so your Gmc Sierra 1500 Extended Cab leaves with evidence, not assumptions.
Documentation Package: Scan Reports, Calibration Results, and Verification Drive Notes
For a Gmc Sierra 1500 Extended Cab, a strong documentation package protects the driver, the shop, and the claim file. Industry workflows and OEM guidance emphasize: pre-scan, identify required calibrations/aiming, verify prerequisites, complete calibration, then confirm with a clean post-repair scan, because warning lights aren't a reliable substitute for documented diagnostics. Keep the packet simple and complete: a pre-calibration scan report (VIN plus all modules), the calibration result report/certificate, and a post-calibration scan showing no relevant DTCs and systems reporting ready. Add proof of process: the OEM procedure source and date, the scan/calibration platform used, and prerequisite checks (tire size uniformity, pressures at spec, ride height/levelness, alignment when required, and obstruction checks). For windshield camera work, include photos of the viewing area and camera bracket plus target setup measurements for static routines. If a dynamic routine was required, add brief verification drive notes (conditions, time/distance, and whether ADAS DTCs returned). At Bang AutoGlass, we keep this customer- and insurance-ready, offer mobile service (often next day), and back workmanship with a lifetime warranty; most windshield replacements take 30-45 minutes plus at least one hour of cure time before drive-away.
Services
Service Areas
Pre- and Post-Calibration Scans for Gmc Sierra 1500 Extended Cab: Proving Systems Are Set Correctly
Scanning vs Calibration on Gmc Sierra 1500 Extended Cab: What Each Step Proves
For your Gmc Sierra 1500 Extended Cab, a scan and a calibration are not interchangeable, even when both are part of the same visit. A diagnostic scan queries the vehicle computers and reports DTCs, communication faults, and system status. It answers what the Gmc Sierra 1500 Extended Cab is reporting right now and creates a baseline you can compare before and after repair. Calibration is the OEM accuracy procedure for ADAS. It validates camera and sensor alignment so the system interprets lane markings, distance, and objects within specification. Depending on the Gmc Sierra 1500 Extended Cab, calibration may be a static target setup, a defined dynamic drive, or both. A scan can be clean while a sensor is still outside tolerance, which can change how lane keep assist, forward collision warning, adaptive cruise control, and automatic emergency braking behave after windshield replacement. Bang AutoGlass treats this as verification: pre-scan, perform OEM-required calibration when applicable, then post-scan to document a clean report. We provide mobile auto glass service, often as soon as next day. Most windshield replacements take 30-45 minutes plus at least one hour adhesive cure time before safe drive-away. Every job includes a lifetime workmanship warranty, and we work with any insurance carrier when comprehensive coverage applies.
Pre-Calibration Scan: Capturing DTCs, Baselines, and Calibration Triggers
Before calibrating ADAS on a Gmc Sierra 1500 Extended Cab, the pre-calibration scan is the control point. We run a full diagnostic scan to record DTCs, module communication health, and system readiness before any calibration begins. This baseline documents what existed prior to repair and gives you a report to compare with the post-scan. The scan also flags issues that can derail calibration, including low battery voltage, network faults, and unrelated stored codes. Correct these first so the calibration routine runs under stable conditions. Scan results support OEM guidance on when calibration is required for your Gmc Sierra 1500 Extended Cab. Typical triggers include windshield replacement with a forward-facing camera, camera or bracket removal, alignment or suspension changes that alter ride height, and repairs affecting sensor mounting angles. If ADAS DTCs or calibration-incomplete events are present, calibration supports lane keep assist, forward collision warning, adaptive cruise control, and automatic emergency braking. Bang AutoGlass saves the scan report, follows OEM service information for the required method, then completes a post-scan to document a clean report. We provide mobile service, often as soon as next day, with 30-45 minute glass work plus at least one hour adhesive cure time before safe drive-away.
Where to Find OEM Requirements for Gmc Sierra 1500 Extended Cab: Position Statements and Service Info
For a Gmc Sierra 1500 Extended Cab, OEM service information is the source of truth for scanning and ADAS calibration. It specifies the events that require calibration, the approved tooling, and the exact steps for static target placement and/or a required dynamic drive cycle. Many manufacturers also publish position statements that outline expectations for pre- and post-repair scanning, windshield replacement considerations, and calibration documentation. To locate requirements quickly, start at the OEM technical portal and search by year and Gmc Sierra 1500 Extended Cab. Review Driver Assistance or ADAS sections, windshield or glass procedures, and diagnostic pages tied to relevant DTCs. Industry research and lookup tools can help identify likely calibrations and prerequisites, but confirm the final procedure in OEM documentation before work is performed. If the OEM provides a position statement PDF, keep it with your scan reports and calibration records. Bang AutoGlass follows the OEM workflow and documents the requirement, the method performed, and the before/after scan results in clear, insurer-friendly language for safety, liability, and claims support. The goal is proof that your Gmc Sierra 1500 Extended Cab was scanned, calibrated when required, and verified afterward.
Set-Up Checks Before Calibration: Glass, Brackets, Tires, Ride Height, and Environment
Pre-checks before calibrating a Gmc Sierra 1500 Extended Cab aren't "extra" - they're the conditions the OEM assumes before a camera or radar calibration can be trusted. Start with the windshield and camera hardware: verify the correct windshield specification for the Gmc Sierra 1500 Extended Cab, clean the camera viewing area, and inspect the camera bracket and mounting surfaces for damage, looseness, or contamination. If the bracket is shifted, the camera sits at the wrong angle and the routine may complete with marginal accuracy. Next, restore OEM stance. Confirm tire sizes match side-to-side, set tire pressures to door-jamb spec, verify TPMS operation, and remove heavy cargo that alters ride height. If the Gmc Sierra 1500 Extended Cab was lifted/lowered or recently had steering or suspension work, complete required repairs and alignment first, then calibrate. Finally, match the environment to the method. Static calibration typically needs a level floor, precise target distances from OEM reference points, correct target type, and controlled lighting to prevent glare. Dynamic calibration may require an OEM-defined drive cycle on clearly marked roads with good visibility. At Bang AutoGlass, we coordinate mobile windshield replacement and clear prep steps so your Gmc Sierra 1500 Extended Cab meets OEM prerequisites before calibration begins.
Post-Calibration Scan and Health Check: Confirming DTCs Are Cleared and Modules Report Ready
A post-calibration scan is what turns "we ran calibration" into "the Gmc Sierra 1500 Extended Cab is verified." After completing the OEM procedure, run a full-system diagnostic post-scan to check for remaining Diagnostic Trouble Codes (DTCs), confirm modules communicate normally, and document whether ADAS-related faults cleared. Many vehicles set "calibration incomplete" or history codes during the routine, so best practice is scan -> clear applicable faults -> rescan after the procedure (and after any required ignition cycle). Verification is more than watching the dash: OEM guidance generally treats warning lights as insufficient proof of system health. Depending on the Gmc Sierra 1500 Extended Cab, confirm status flags such as calibrated/initialized/not learned, and complete any OEM-required learning or verification drive so the system reports fully ready. If the post-scan shows persistent DTCs tied to the forward camera, lane keeping, forward collision warning, adaptive cruise, blind spot monitoring, or automatic emergency braking, stop and diagnose instead of guessing. Save the scan report as the documented "after" snapshot - often expected by insurers and safety audits - so your Gmc Sierra 1500 Extended Cab leaves with evidence, not assumptions.
Documentation Package: Scan Reports, Calibration Results, and Verification Drive Notes
For a Gmc Sierra 1500 Extended Cab, a strong documentation package protects the driver, the shop, and the claim file. Industry workflows and OEM guidance emphasize: pre-scan, identify required calibrations/aiming, verify prerequisites, complete calibration, then confirm with a clean post-repair scan, because warning lights aren't a reliable substitute for documented diagnostics. Keep the packet simple and complete: a pre-calibration scan report (VIN plus all modules), the calibration result report/certificate, and a post-calibration scan showing no relevant DTCs and systems reporting ready. Add proof of process: the OEM procedure source and date, the scan/calibration platform used, and prerequisite checks (tire size uniformity, pressures at spec, ride height/levelness, alignment when required, and obstruction checks). For windshield camera work, include photos of the viewing area and camera bracket plus target setup measurements for static routines. If a dynamic routine was required, add brief verification drive notes (conditions, time/distance, and whether ADAS DTCs returned). At Bang AutoGlass, we keep this customer- and insurance-ready, offer mobile service (often next day), and back workmanship with a lifetime warranty; most windshield replacements take 30-45 minutes plus at least one hour of cure time before drive-away.
Enjoy More Relevant Blogs
Tempered vs Laminated Door Glass on Dodge Ram 2500 Regular Cab: What’s Used and Why It Matters
Tempered vs laminated door glass on Dodge Ram 2500 Regular Cab: what your vehicle uses, how it breaks, and what it means for replacement safety, cost, and cleanup.
How to Schedule ADAS Calibration for Ford F250 Super Duty Crew Cab After Windshield Replacement
Schedule ADAS calibration for Ford F250 Super Duty Crew Cab after windshield replacement. Learn timing, required info, and what to expect so safety systems stay accurate.
After a Break-In: Dodge Challenger Quarter Glass Replacement Plan to Restore Security and Visibility
After a break-in on Dodge Challenger, restore security with a quarter glass replacement plan: cleanup, temporary protection, scheduling, and post-install checks.
Will Insurance Cover Door Glass Replacement for a Ford Focus RS? Claims Steps, Deductibles, and What to Document
Will insurance cover Ford Focus RS door glass replacement? Learn claim steps, deductibles, photos to document, and how to schedule fast repairs today.
ADAS After Windshield Replacement on Gmc Terrain: Calibration Basics and Safety Checks
ADAS after Gmc Terrain windshield replacement: calibration basics, common safety checks, and how to confirm cameras and sensors are working correctly.
How to Schedule Mobile Rear Glass Replacement for Gmc Rally Wagon 2500
Schedule mobile rear glass replacement for your Gmc Rally Wagon 2500 in minutes. Learn what info to provide, how long it takes, and prep tips for service day.
Stop Leaks and Wind Noise: What Proper Dodge Durango Quarter Glass Replacement Should Prevent
Stop leaks and wind noise with proper Dodge Durango quarter glass replacement. Learn what correct fit, sealing, and trim should prevent after install.
Tempered Safety Rear Glass Replacement for Gmc Canyon Crew Cab: Understanding DOT Markings and FMVSS 205
Need Gmc Canyon Crew Cab rear glass replacement? Learn tempered safety glass basics, DOT markings, and FMVSS 205, plus install and cure tips. Get a quote today.
Post-Install Checks for Gmc Sierra (Classic) 1500 Extended Cab: Rear Glass Replacement Wind Noise, Leaks, and Rattle Tests
Post-install rear glass checks for Gmc Sierra (Classic) 1500 Extended Cab: test for wind noise, leaks, and rattles, plus when to return for warranty service—check today before trips.
Fast Scheduling Guide: Gmc Sierra 3500 Hd Extended Cab Windshield Replacement From Booking to Install
Book Gmc Sierra 3500 Hd Extended Cab windshield replacement fast. See scheduling steps, what to prep, install timing, and when you can safely drive away. Get a quote today.
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm