Services
Service Areas
Cleanup After Quarter Window Breakage on Mazda Cx-3: Safe Glass Removal and Interior Protection
After a quarter window shatters on your Mazda Cx-3, it’s tempting to focus on replacement first, but the priority is making the cabin safe and stopping debris from spreading. Tempered quarter glass breaks into hard pellets that roll under seat rails and wedge into carpet backing. If you must drive, remove passengers and loose items, then suit up with gloves, eye protection, and closed-toe shoes. Pull the largest chunks from the opening and lower ledge and place them in a rigid box or thick bag. Next, vacuum in stages using a crevice tool—start at the headliner edge and trim seams, then seats and belt receivers, then the floor and cargo area. Avoid sweeping with a shop broom; it grinds fragments into fabric. For upholstery, press wide tape or a lint roller to collect glitter-like shards, and finish plastics with a damp microfiber that traps fines instead of moving them around. If weather is an issue, tape plastic sheeting from the inside with painter’s tape; avoid duct tape that can pull paint. When you schedule Bang AutoGlass for mobile quarter window replacement, we confirm fitment and perform a final interior glass sweep so your Mazda Cx-3 returns to a comfortable, safe daily driver.
Verify the Correct Quarter Glass for Mazda Cx-3: Fixed vs Pop-Out, Tint Match, and DOT Markings
Before installing a new quarter window on your Mazda Cx-3, we verify exact fitment, because an “almost right” piece can cause leaks, wind noise, trim gaps, or a tint mismatch that’s obvious in daylight. First we confirm the quarter glass style: fixed glass bonded with urethane versus a pop-out/vent unit with hinges or latches. We match your Mazda Cx-3 body style, model-year range, and left/right orientation. Next we align appearance and solar performance—clear versus factory privacy tint, shade consistency, and how any existing window film will blend so the replacement doesn’t stand out. We also check the glass “bug” markings: DOT codes, safety identifiers, manufacturer traceability, and the correct AS rating for non-windshield glazing. Many quarter windows arrive as an encapsulated assembly with pre-attached molding, studs, locator pins, or clips; those details control seating depth, reveal lines, and how interior panels lock back in. When applicable, we confirm embedded features such as antenna elements. The result is an OEM-correct Mazda Cx-3 quarter window replacement that seals properly. If comprehensive insurance applies, Bang AutoGlass works with all insurance companies and can help you complete the claim steps on-site.
Remove Trim and Old Glass: Mazda Cx-3 Quarter Window Replacement Disassembly Checklist
For a Mazda Cx-3 quarter window replacement, the craftsmanship is in the take-apart: reach the glass without scuffing paint, bending the flange, or breaking small clips that later become squeaks. We start by clearing the quarter area, lowering the rear seat if needed, and covering seats and carpet. After masking the exterior edge with protective tape, we work panel-by-panel with non-marring tools, finding hidden screws and push-pins and keeping hardware grouped for accurate reassembly. Because quarter trim often sits near curtain airbags and seatbelt anchors, we follow safe access points and avoid disturbing restraint components. Once exposed, we determine how the glass is retained. On bonded applications, we cut the urethane bead in a controlled way—often with a cold-knife or wire system—so the pane releases without gouging the pinchweld. On bolt-in or framed designs, we support the glass while retainers are removed and watch locator pins that can snap if the pane shifts. After removal, we clear remaining fragments, inspect moldings, and prep the opening for bonding and installation. Most mobile swaps take roughly 30–45 minutes, with cure time afterward based on the adhesive system.
Prep the Pinchweld and Bond Area: Corrosion Checks, Primers, and Adhesion Readiness
A clean, long-lasting quarter window replacement on your Mazda Cx-3 starts with bond prep, not the new glass. For bonded quarter glass, the pinchweld (the metal flange around the opening) and the glass bond band must be stable and clean so urethane can fully adhere. At Bang AutoGlass, we begin with a corrosion and coating check for rust, bubbling paint, exposed metal, and prior repair residue that can weaken the seal and cause leaks. We preserve factory E-coat and sound paint whenever possible, then trim the old urethane down to a thin, uniform base layer so fresh urethane can bond to a consistent substrate. If any bare metal is exposed from corrosion cleanup or a cutting nick, we treat it with the correct refinish/body primer per adhesive and refinish guidance, and apply pinchweld primer when the urethane system requires it. On the glass side, we clean the bond area and use the appropriate activator or glass/frit primer as specified to promote adhesion and UV protection at the bond line. Contamination control is strict: no silicone products, no oily fingerprints, and no skipped flash times. We dry-fit the quarter glass to confirm alignment, reveal, and trim engagement, then mask adjacent paint for a crisp finished edge. This prep prevents water intrusion and supports an OEM-style seal—often completed at your location by our mobile auto glass team.
Urethane Bonding and Minimum Drive-Away Time for Mazda Cx-3: SDAT Factors You Must Follow
Bonding is where a Mazda Cx-3 quarter window replacement becomes either a quiet, watertight repair or a repeat leak and wind-noise complaint. Bang AutoGlass uses automotive-grade urethane and applies a continuous, properly sized bead to maintain correct stand-off, seat depth, and molding support. We pay special attention to corners and transitions, where gaps or thin spots can become water paths. After the bead is laid, the quarter glass is set on its locators, aligned to body lines, and pressed evenly to achieve full contact without collapsing the bead. We then secure and re-check flushness so the glass cannot shift while curing begins. Safe Drive-Away Time (SDAT) is required guidance and varies by urethane formula plus ambient temperature and relative humidity. Cooler and drier conditions generally slow cure, while warmer and more humid conditions typically accelerate it, which is why professional systems publish SDAT charts and procedures. As a practical baseline, we require at least one full hour before your Mazda Cx-3 is considered safe to drive, even when the install itself commonly takes about 30–45 minutes. During early cure, avoid door slams, aggressive window operation, or rough roads that flex the opening. For best results, postpone high-pressure washing for 24–48 hours and keep the bond line clean and undisturbed. Our mobile auto glass team can complete the job at your location, and we work with all insurance companies when comprehensive coverage applies.
Final Quality Checks: Leak Test, Wind Noise, Trim Fit, and Documentation for Mazda Cx-3
Our last phase on a Mazda Cx-3 quarter window replacement is inspection and validation, because an install that looks fine can still leak or whistle if alignment and trim engagement are off by millimeters. We start with a full visual check from inside and outside, confirming the quarter glass is seated evenly, the reveal line is consistent, and the molding/encapsulation is flush with the body with no waves, corner lifts, or gaps. We verify the surrounding trim fits without stress, then re-check interior panel clips and fasteners to prevent future rattles in the quarter and cargo area. Next, we perform a controlled water test using steady flow along the perimeter while observing the interior edge and quarter cavity for any moisture. If wind noise is a concern, we focus on perimeter contact points and trim alignment, since small edge separations can become very noticeable at speed. We then clean the glass, remove protective tape, and ensure the vehicle is returned in clean condition with no residue on paint or plastics. To close out, we provide documentation: glass identification markings, installation notes, and aftercare guidance, including honoring the minimum one-hour safe drive-away time and avoiding high-pressure washes for 24–48 hours. You also receive warranty information so there is a straightforward path to support if you ever need it. If comprehensive insurance coverage applies, Bang AutoGlass can coordinate claim documentation with the insurer to keep the process efficient. The result is a Mazda Cx-3 quarter window replacement that is verified, documented, and ready for normal use.
Services
Service Areas
Cleanup After Quarter Window Breakage on Mazda Cx-3: Safe Glass Removal and Interior Protection
After a quarter window shatters on your Mazda Cx-3, it’s tempting to focus on replacement first, but the priority is making the cabin safe and stopping debris from spreading. Tempered quarter glass breaks into hard pellets that roll under seat rails and wedge into carpet backing. If you must drive, remove passengers and loose items, then suit up with gloves, eye protection, and closed-toe shoes. Pull the largest chunks from the opening and lower ledge and place them in a rigid box or thick bag. Next, vacuum in stages using a crevice tool—start at the headliner edge and trim seams, then seats and belt receivers, then the floor and cargo area. Avoid sweeping with a shop broom; it grinds fragments into fabric. For upholstery, press wide tape or a lint roller to collect glitter-like shards, and finish plastics with a damp microfiber that traps fines instead of moving them around. If weather is an issue, tape plastic sheeting from the inside with painter’s tape; avoid duct tape that can pull paint. When you schedule Bang AutoGlass for mobile quarter window replacement, we confirm fitment and perform a final interior glass sweep so your Mazda Cx-3 returns to a comfortable, safe daily driver.
Verify the Correct Quarter Glass for Mazda Cx-3: Fixed vs Pop-Out, Tint Match, and DOT Markings
Before installing a new quarter window on your Mazda Cx-3, we verify exact fitment, because an “almost right” piece can cause leaks, wind noise, trim gaps, or a tint mismatch that’s obvious in daylight. First we confirm the quarter glass style: fixed glass bonded with urethane versus a pop-out/vent unit with hinges or latches. We match your Mazda Cx-3 body style, model-year range, and left/right orientation. Next we align appearance and solar performance—clear versus factory privacy tint, shade consistency, and how any existing window film will blend so the replacement doesn’t stand out. We also check the glass “bug” markings: DOT codes, safety identifiers, manufacturer traceability, and the correct AS rating for non-windshield glazing. Many quarter windows arrive as an encapsulated assembly with pre-attached molding, studs, locator pins, or clips; those details control seating depth, reveal lines, and how interior panels lock back in. When applicable, we confirm embedded features such as antenna elements. The result is an OEM-correct Mazda Cx-3 quarter window replacement that seals properly. If comprehensive insurance applies, Bang AutoGlass works with all insurance companies and can help you complete the claim steps on-site.
Remove Trim and Old Glass: Mazda Cx-3 Quarter Window Replacement Disassembly Checklist
For a Mazda Cx-3 quarter window replacement, the craftsmanship is in the take-apart: reach the glass without scuffing paint, bending the flange, or breaking small clips that later become squeaks. We start by clearing the quarter area, lowering the rear seat if needed, and covering seats and carpet. After masking the exterior edge with protective tape, we work panel-by-panel with non-marring tools, finding hidden screws and push-pins and keeping hardware grouped for accurate reassembly. Because quarter trim often sits near curtain airbags and seatbelt anchors, we follow safe access points and avoid disturbing restraint components. Once exposed, we determine how the glass is retained. On bonded applications, we cut the urethane bead in a controlled way—often with a cold-knife or wire system—so the pane releases without gouging the pinchweld. On bolt-in or framed designs, we support the glass while retainers are removed and watch locator pins that can snap if the pane shifts. After removal, we clear remaining fragments, inspect moldings, and prep the opening for bonding and installation. Most mobile swaps take roughly 30–45 minutes, with cure time afterward based on the adhesive system.
Prep the Pinchweld and Bond Area: Corrosion Checks, Primers, and Adhesion Readiness
A clean, long-lasting quarter window replacement on your Mazda Cx-3 starts with bond prep, not the new glass. For bonded quarter glass, the pinchweld (the metal flange around the opening) and the glass bond band must be stable and clean so urethane can fully adhere. At Bang AutoGlass, we begin with a corrosion and coating check for rust, bubbling paint, exposed metal, and prior repair residue that can weaken the seal and cause leaks. We preserve factory E-coat and sound paint whenever possible, then trim the old urethane down to a thin, uniform base layer so fresh urethane can bond to a consistent substrate. If any bare metal is exposed from corrosion cleanup or a cutting nick, we treat it with the correct refinish/body primer per adhesive and refinish guidance, and apply pinchweld primer when the urethane system requires it. On the glass side, we clean the bond area and use the appropriate activator or glass/frit primer as specified to promote adhesion and UV protection at the bond line. Contamination control is strict: no silicone products, no oily fingerprints, and no skipped flash times. We dry-fit the quarter glass to confirm alignment, reveal, and trim engagement, then mask adjacent paint for a crisp finished edge. This prep prevents water intrusion and supports an OEM-style seal—often completed at your location by our mobile auto glass team.
Urethane Bonding and Minimum Drive-Away Time for Mazda Cx-3: SDAT Factors You Must Follow
Bonding is where a Mazda Cx-3 quarter window replacement becomes either a quiet, watertight repair or a repeat leak and wind-noise complaint. Bang AutoGlass uses automotive-grade urethane and applies a continuous, properly sized bead to maintain correct stand-off, seat depth, and molding support. We pay special attention to corners and transitions, where gaps or thin spots can become water paths. After the bead is laid, the quarter glass is set on its locators, aligned to body lines, and pressed evenly to achieve full contact without collapsing the bead. We then secure and re-check flushness so the glass cannot shift while curing begins. Safe Drive-Away Time (SDAT) is required guidance and varies by urethane formula plus ambient temperature and relative humidity. Cooler and drier conditions generally slow cure, while warmer and more humid conditions typically accelerate it, which is why professional systems publish SDAT charts and procedures. As a practical baseline, we require at least one full hour before your Mazda Cx-3 is considered safe to drive, even when the install itself commonly takes about 30–45 minutes. During early cure, avoid door slams, aggressive window operation, or rough roads that flex the opening. For best results, postpone high-pressure washing for 24–48 hours and keep the bond line clean and undisturbed. Our mobile auto glass team can complete the job at your location, and we work with all insurance companies when comprehensive coverage applies.
Final Quality Checks: Leak Test, Wind Noise, Trim Fit, and Documentation for Mazda Cx-3
Our last phase on a Mazda Cx-3 quarter window replacement is inspection and validation, because an install that looks fine can still leak or whistle if alignment and trim engagement are off by millimeters. We start with a full visual check from inside and outside, confirming the quarter glass is seated evenly, the reveal line is consistent, and the molding/encapsulation is flush with the body with no waves, corner lifts, or gaps. We verify the surrounding trim fits without stress, then re-check interior panel clips and fasteners to prevent future rattles in the quarter and cargo area. Next, we perform a controlled water test using steady flow along the perimeter while observing the interior edge and quarter cavity for any moisture. If wind noise is a concern, we focus on perimeter contact points and trim alignment, since small edge separations can become very noticeable at speed. We then clean the glass, remove protective tape, and ensure the vehicle is returned in clean condition with no residue on paint or plastics. To close out, we provide documentation: glass identification markings, installation notes, and aftercare guidance, including honoring the minimum one-hour safe drive-away time and avoiding high-pressure washes for 24–48 hours. You also receive warranty information so there is a straightforward path to support if you ever need it. If comprehensive insurance coverage applies, Bang AutoGlass can coordinate claim documentation with the insurer to keep the process efficient. The result is a Mazda Cx-3 quarter window replacement that is verified, documented, and ready for normal use.
Services
Service Areas
Cleanup After Quarter Window Breakage on Mazda Cx-3: Safe Glass Removal and Interior Protection
After a quarter window shatters on your Mazda Cx-3, it’s tempting to focus on replacement first, but the priority is making the cabin safe and stopping debris from spreading. Tempered quarter glass breaks into hard pellets that roll under seat rails and wedge into carpet backing. If you must drive, remove passengers and loose items, then suit up with gloves, eye protection, and closed-toe shoes. Pull the largest chunks from the opening and lower ledge and place them in a rigid box or thick bag. Next, vacuum in stages using a crevice tool—start at the headliner edge and trim seams, then seats and belt receivers, then the floor and cargo area. Avoid sweeping with a shop broom; it grinds fragments into fabric. For upholstery, press wide tape or a lint roller to collect glitter-like shards, and finish plastics with a damp microfiber that traps fines instead of moving them around. If weather is an issue, tape plastic sheeting from the inside with painter’s tape; avoid duct tape that can pull paint. When you schedule Bang AutoGlass for mobile quarter window replacement, we confirm fitment and perform a final interior glass sweep so your Mazda Cx-3 returns to a comfortable, safe daily driver.
Verify the Correct Quarter Glass for Mazda Cx-3: Fixed vs Pop-Out, Tint Match, and DOT Markings
Before installing a new quarter window on your Mazda Cx-3, we verify exact fitment, because an “almost right” piece can cause leaks, wind noise, trim gaps, or a tint mismatch that’s obvious in daylight. First we confirm the quarter glass style: fixed glass bonded with urethane versus a pop-out/vent unit with hinges or latches. We match your Mazda Cx-3 body style, model-year range, and left/right orientation. Next we align appearance and solar performance—clear versus factory privacy tint, shade consistency, and how any existing window film will blend so the replacement doesn’t stand out. We also check the glass “bug” markings: DOT codes, safety identifiers, manufacturer traceability, and the correct AS rating for non-windshield glazing. Many quarter windows arrive as an encapsulated assembly with pre-attached molding, studs, locator pins, or clips; those details control seating depth, reveal lines, and how interior panels lock back in. When applicable, we confirm embedded features such as antenna elements. The result is an OEM-correct Mazda Cx-3 quarter window replacement that seals properly. If comprehensive insurance applies, Bang AutoGlass works with all insurance companies and can help you complete the claim steps on-site.
Remove Trim and Old Glass: Mazda Cx-3 Quarter Window Replacement Disassembly Checklist
For a Mazda Cx-3 quarter window replacement, the craftsmanship is in the take-apart: reach the glass without scuffing paint, bending the flange, or breaking small clips that later become squeaks. We start by clearing the quarter area, lowering the rear seat if needed, and covering seats and carpet. After masking the exterior edge with protective tape, we work panel-by-panel with non-marring tools, finding hidden screws and push-pins and keeping hardware grouped for accurate reassembly. Because quarter trim often sits near curtain airbags and seatbelt anchors, we follow safe access points and avoid disturbing restraint components. Once exposed, we determine how the glass is retained. On bonded applications, we cut the urethane bead in a controlled way—often with a cold-knife or wire system—so the pane releases without gouging the pinchweld. On bolt-in or framed designs, we support the glass while retainers are removed and watch locator pins that can snap if the pane shifts. After removal, we clear remaining fragments, inspect moldings, and prep the opening for bonding and installation. Most mobile swaps take roughly 30–45 minutes, with cure time afterward based on the adhesive system.
Prep the Pinchweld and Bond Area: Corrosion Checks, Primers, and Adhesion Readiness
A clean, long-lasting quarter window replacement on your Mazda Cx-3 starts with bond prep, not the new glass. For bonded quarter glass, the pinchweld (the metal flange around the opening) and the glass bond band must be stable and clean so urethane can fully adhere. At Bang AutoGlass, we begin with a corrosion and coating check for rust, bubbling paint, exposed metal, and prior repair residue that can weaken the seal and cause leaks. We preserve factory E-coat and sound paint whenever possible, then trim the old urethane down to a thin, uniform base layer so fresh urethane can bond to a consistent substrate. If any bare metal is exposed from corrosion cleanup or a cutting nick, we treat it with the correct refinish/body primer per adhesive and refinish guidance, and apply pinchweld primer when the urethane system requires it. On the glass side, we clean the bond area and use the appropriate activator or glass/frit primer as specified to promote adhesion and UV protection at the bond line. Contamination control is strict: no silicone products, no oily fingerprints, and no skipped flash times. We dry-fit the quarter glass to confirm alignment, reveal, and trim engagement, then mask adjacent paint for a crisp finished edge. This prep prevents water intrusion and supports an OEM-style seal—often completed at your location by our mobile auto glass team.
Urethane Bonding and Minimum Drive-Away Time for Mazda Cx-3: SDAT Factors You Must Follow
Bonding is where a Mazda Cx-3 quarter window replacement becomes either a quiet, watertight repair or a repeat leak and wind-noise complaint. Bang AutoGlass uses automotive-grade urethane and applies a continuous, properly sized bead to maintain correct stand-off, seat depth, and molding support. We pay special attention to corners and transitions, where gaps or thin spots can become water paths. After the bead is laid, the quarter glass is set on its locators, aligned to body lines, and pressed evenly to achieve full contact without collapsing the bead. We then secure and re-check flushness so the glass cannot shift while curing begins. Safe Drive-Away Time (SDAT) is required guidance and varies by urethane formula plus ambient temperature and relative humidity. Cooler and drier conditions generally slow cure, while warmer and more humid conditions typically accelerate it, which is why professional systems publish SDAT charts and procedures. As a practical baseline, we require at least one full hour before your Mazda Cx-3 is considered safe to drive, even when the install itself commonly takes about 30–45 minutes. During early cure, avoid door slams, aggressive window operation, or rough roads that flex the opening. For best results, postpone high-pressure washing for 24–48 hours and keep the bond line clean and undisturbed. Our mobile auto glass team can complete the job at your location, and we work with all insurance companies when comprehensive coverage applies.
Final Quality Checks: Leak Test, Wind Noise, Trim Fit, and Documentation for Mazda Cx-3
Our last phase on a Mazda Cx-3 quarter window replacement is inspection and validation, because an install that looks fine can still leak or whistle if alignment and trim engagement are off by millimeters. We start with a full visual check from inside and outside, confirming the quarter glass is seated evenly, the reveal line is consistent, and the molding/encapsulation is flush with the body with no waves, corner lifts, or gaps. We verify the surrounding trim fits without stress, then re-check interior panel clips and fasteners to prevent future rattles in the quarter and cargo area. Next, we perform a controlled water test using steady flow along the perimeter while observing the interior edge and quarter cavity for any moisture. If wind noise is a concern, we focus on perimeter contact points and trim alignment, since small edge separations can become very noticeable at speed. We then clean the glass, remove protective tape, and ensure the vehicle is returned in clean condition with no residue on paint or plastics. To close out, we provide documentation: glass identification markings, installation notes, and aftercare guidance, including honoring the minimum one-hour safe drive-away time and avoiding high-pressure washes for 24–48 hours. You also receive warranty information so there is a straightforward path to support if you ever need it. If comprehensive insurance coverage applies, Bang AutoGlass can coordinate claim documentation with the insurer to keep the process efficient. The result is a Mazda Cx-3 quarter window replacement that is verified, documented, and ready for normal use.
Enjoy More Relevant Blogs
How to Schedule Mobile Quarter Glass Replacement for Mazda Cx-3
Need mobile quarter glass replacement for Mazda Cx-3? Follow our scheduling checklist, photos to take, timing, and on-site tips to restore security.
OEM-Quality Quarter Glass Replacement for Mazda Cx-3: Fit, Trim, and Weather-Seal Checklist
OEM-quality quarter glass replacement for Mazda Cx-3: fit, trim, and weather-seal checklist for correct install, leak prevention, and clean finish.
Stop Leaks and Wind Noise: What Proper Mazda Cx-3 Quarter Glass Replacement Should Prevent
Stop leaks and wind noise with proper Mazda Cx-3 quarter glass replacement. Learn what correct fit, sealing, and trim should prevent after install.
Tint & Privacy Glass Match Guide: Mazda Cx-3 Quarter Glass Replacement Done Right
Tint and privacy match guide for Mazda Cx-3 quarter glass replacement—how to match shade, markings, and fit so the new glass looks factory-perfect.
Safety Standards Explained: DOT Markings and FMVSS 205 for Mazda Cx-3 Quarter Glass Replacement
DOT markings and FMVSS 205 explained for Mazda Cx-3 quarter glass replacement—how to verify safety markings and choose compliant OEM-quality glass.
Fixed Quarter Window vs Vent Glass on Mazda Cx-3: Ordering the Correct Replacement
Fixed quarter window vs vent glass on Mazda Cx-3: how to identify yours and order the correct replacement for fit, sealing, and safety—read this now.
After a Break-In: Mazda Cx-3 Quarter Glass Replacement Plan to Restore Security and Visibility
After a break-in on Mazda Cx-3, restore security with a quarter glass replacement plan: cleanup, temporary protection, scheduling, and post-install checks.
How Long After Mazda Cx-3 Quarter Panel Glass Replacement Can You Drive or Wash the Car? Urethane Cure-Time Rules
After Mazda Cx-3 quarter panel glass replacement, learn safe drive-away time, when to wash, and urethane cure rules that help prevent leaks and wind noise.
How Much Does Mazda Cx-3 Quarter Panel Glass Replacement Cost? Insurance Deductibles, Estimates, and Ways to Save
Cost to replace Mazda Cx-3 quarter panel glass: key price factors, OEM vs aftermarket options, insurance deductibles, estimates, and smart ways to save.
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm