Services
Service Areas
Shattered Back Window on Mercedes-Benz 190 E: A Step-by-Step Rear Glass Replacement Plan
Immediate Steps After Rear Glass Breakage on Mercedes-Benz 190 E: Safety, Visibility, and Securing the Vehicle
If the rear window on your Mercedes-Benz 190 E shatters, treat it as a safety and security issue until a professional rear window replacement is completed. If it breaks while driving, slow down, turn on hazard lights, and pull into a safe, well-lit area. Tempered back glass fractures into small cubes, but they can still cut skin and irritate eyes--avoid touching your face and keep children and pets away. With gloves and eye protection, remove only loose pieces that block visibility or could drop into the cabin. Next, protect the interior from weather and theft. Remove valuables and cover the opening with plastic sheeting or a heavy-duty bag, securing it with painter's tape or other low-tack tape. Do not slam doors or the hatch; pressure changes can dislodge remaining glass. Take photos for an insurance claim, since rear glass damage is commonly handled under comprehensive coverage. Bang AutoGlass makes Mercedes-Benz 190 E back glass replacement straightforward with fully mobile service, often as soon as next day. Most installs take about 30-45 minutes on site, then the urethane requires at least 1 hour of cure time before safe drive-away. Every job is backed by our lifetime workmanship warranty.
Cleanup Plan: Removing Shards, Vacuuming the Cabin, and Protecting Trim and Upholstery
A shattered rear window spreads sharp fragments through your Mercedes-Benz 190 E, so handle cleanup like a controlled detail job. Start with PPE: closed-toe shoes, thick gloves, and eye protection. Keep passengers out of the cabin. If possible, drape plastic sheeting over seats, the rear deck/parcel shelf, and the cargo area before you move glass so shards do not get ground into fabric. Remove the largest pieces first. Lift chunks from the frame and rear deck by hand and place them into a rigid box or thick contractor bag. Then vacuum slowly with a shop-vac or strong household vacuum and a crevice tool. Work top-down in a repeatable route: headliner edge, trim gaps, rear deck, seat seams, floor mats, carpet, and the trunk or cargo well, including the spare-tire compartment. After vacuuming, use painter's tape, packing tape wrapped sticky-side out, or a lint roller to lift fine "glass sand" from upholstery and corners; repeat until the tape comes back clean. Finish with gentle vacuum passes and a slightly damp microfiber towel on plastics to avoid scratches. Leave the opening accessible so a mobile rear window replacement can be installed cleanly and securely.
Confirm the Correct Rear Glass for Mercedes-Benz 190 E: Defroster Grid, Antenna Lines, Tint, and DOT Markings
Ordering the rear glass for a Mercedes-Benz 190 E starts with matching the vehicle's options. Begin with the rear defroster: most Mercedes-Benz 190 E back windows use a printed heating grid, and the replacement must match the layout and have the connector tabs so it plugs into the factory harness. Also confirm antenna features. Many vehicles integrate AM/FM, GPS, or cellular traces into the rear window; if your reception depended on the original glass, you need an antenna-equipped replacement. Next, match tint and privacy shading. Rear glass may be clear, lightly tinted, or privacy glass. Matching shade matters for appearance, heat rejection, and (by state) compliance. If your Mercedes-Benz 190 E had aftermarket tint film, confirm whether film was applied over clear glass or whether the vehicle used privacy glass so you do not end up too light or too dark after rear windshield replacement. Finally, verify markings and fit. Automotive glass carries DOT identification and AS markings (AS2/AS3 are common on rear and side glass and can indicate tinted variations). VIN validation and the part number help ensure proper curvature, tempered-glass performance, and an insurance-friendly repair. Bang AutoGlass verifies these details before dispatching our mobile team, and every install is backed by our lifetime workmanship warranty.
Removal and Prep Steps: Interior Protection, Pinchweld Inspection, and Bond Surface Readiness
Removal and preparation are the foundation of a leak-free rear window replacement on your Mercedes-Benz 190 E. We start with containment: seats, the rear deck, and the cargo area are covered so glass pellets and adhesive debris don't contaminate the interior. Trim, fasteners, and moldings are removed in the proper sequence to protect clips and keep the opening accessible, and defroster/antenna leads are secured so wiring isn't strained. Next, the old urethane is cut and reduced to create a stable bonding surface. Standard methods remove most cured adhesive while leaving an even base layer (about 1-2 mm) so new urethane bonds to existing urethane rather than bare metal. We inspect the pinchweld for scratches through paint, rust, contamination, or misalignment from prior repairs, then treat, prime, and seal any exposed metal because corrosion under the bond line can cause leaks and adhesion loss. Before installation, we dry-fit the replacement rear glass for your Mercedes-Benz 190 E, confirm molding and spacer condition, clean the frit and aperture, and apply the correct primer/activator with proper flash times. This prep discipline lets Bang AutoGlass set the glass evenly and deliver mobile, next-day rear glass replacement backed by a lifetime workmanship warranty.
Urethane Bonding and Minimum Drive-Away Time for Mercedes-Benz 190 E: What Controls Safe Release
The difference between "installed" and "safe" after a Mercedes-Benz 190 E rear window replacement is urethane curing. Auto glass urethane is a moisture-curing polyurethane adhesive, and each system includes Safe Drive-Away Time (SDAT) guidance tied to minimum bond strength. SDAT is controlled by the adhesive used, proper surface prep, bead size/shape, and environmental conditions like temperature and humidity. Cold or very dry air can slow cure; warm, humid conditions typically speed it up. Open-time limits also matter-urethane must be applied and the glass set within the specified window for proper wet-out and adhesion. Prep details directly affect the bond: clean, contaminant-free surfaces; correct primer/activator application; and required flash times. The urethane bead must be continuous and uniform so it compresses evenly around the perimeter, preventing thin spots that can leak or whistle. Exposed metal on the pinchweld must be protected and primed because corrosion under the bond line is a common long-term failure point. At Bang AutoGlass, most Mercedes-Benz 190 E back glass replacements take about 30-45 minutes on site, then we require at least 1 hour before safe drive-away. Drive gently, avoid slamming doors, and skip automated car washes; we'll extend cure time if conditions warrant it, backed by our lifetime workmanship warranty and help with comprehensive coverage claims.
Post-Install Verification: Defroster/Antenna Testing, Leak & Wind Noise Checks, and Documentation
After your Mercedes-Benz 190 E rear window replacement, post-install verification turns new back glass into a reliable, long-term repair. Bang AutoGlass finishes every rear windshield replacement by checking electrical features, sealing, and documentation-especially when an insurance claim under comprehensive coverage is involved. First, we reconnect and secure the rear defroster tabs and any in-glass antenna leads, ensuring connectors are fully seated and wiring is strain-relieved so liftgate or trunk movement won't tug them loose. We can confirm basic operation so you don't discover a weak connection or poor reception later. Next, we validate the seal and noise performance: we inspect molding alignment and the reveal line for even spacing, then perform a controlled perimeter water test to confirm there are no leaks. If wind noise is a concern, a short road test is the most realistic way to replicate airflow and confirm proper set-down. Finally, we document the job with an invoice, warranty record, and notes on glass features for your Mercedes-Benz 190 E (tint, defroster grid, antenna integration, and DOT markings). Observe at least a 1-hour safe drive-away time and avoid automated car washes for the first day to protect the fresh urethane seal.
Services
Service Areas
Shattered Back Window on Mercedes-Benz 190 E: A Step-by-Step Rear Glass Replacement Plan
Immediate Steps After Rear Glass Breakage on Mercedes-Benz 190 E: Safety, Visibility, and Securing the Vehicle
If the rear window on your Mercedes-Benz 190 E shatters, treat it as a safety and security issue until a professional rear window replacement is completed. If it breaks while driving, slow down, turn on hazard lights, and pull into a safe, well-lit area. Tempered back glass fractures into small cubes, but they can still cut skin and irritate eyes--avoid touching your face and keep children and pets away. With gloves and eye protection, remove only loose pieces that block visibility or could drop into the cabin. Next, protect the interior from weather and theft. Remove valuables and cover the opening with plastic sheeting or a heavy-duty bag, securing it with painter's tape or other low-tack tape. Do not slam doors or the hatch; pressure changes can dislodge remaining glass. Take photos for an insurance claim, since rear glass damage is commonly handled under comprehensive coverage. Bang AutoGlass makes Mercedes-Benz 190 E back glass replacement straightforward with fully mobile service, often as soon as next day. Most installs take about 30-45 minutes on site, then the urethane requires at least 1 hour of cure time before safe drive-away. Every job is backed by our lifetime workmanship warranty.
Cleanup Plan: Removing Shards, Vacuuming the Cabin, and Protecting Trim and Upholstery
A shattered rear window spreads sharp fragments through your Mercedes-Benz 190 E, so handle cleanup like a controlled detail job. Start with PPE: closed-toe shoes, thick gloves, and eye protection. Keep passengers out of the cabin. If possible, drape plastic sheeting over seats, the rear deck/parcel shelf, and the cargo area before you move glass so shards do not get ground into fabric. Remove the largest pieces first. Lift chunks from the frame and rear deck by hand and place them into a rigid box or thick contractor bag. Then vacuum slowly with a shop-vac or strong household vacuum and a crevice tool. Work top-down in a repeatable route: headliner edge, trim gaps, rear deck, seat seams, floor mats, carpet, and the trunk or cargo well, including the spare-tire compartment. After vacuuming, use painter's tape, packing tape wrapped sticky-side out, or a lint roller to lift fine "glass sand" from upholstery and corners; repeat until the tape comes back clean. Finish with gentle vacuum passes and a slightly damp microfiber towel on plastics to avoid scratches. Leave the opening accessible so a mobile rear window replacement can be installed cleanly and securely.
Confirm the Correct Rear Glass for Mercedes-Benz 190 E: Defroster Grid, Antenna Lines, Tint, and DOT Markings
Ordering the rear glass for a Mercedes-Benz 190 E starts with matching the vehicle's options. Begin with the rear defroster: most Mercedes-Benz 190 E back windows use a printed heating grid, and the replacement must match the layout and have the connector tabs so it plugs into the factory harness. Also confirm antenna features. Many vehicles integrate AM/FM, GPS, or cellular traces into the rear window; if your reception depended on the original glass, you need an antenna-equipped replacement. Next, match tint and privacy shading. Rear glass may be clear, lightly tinted, or privacy glass. Matching shade matters for appearance, heat rejection, and (by state) compliance. If your Mercedes-Benz 190 E had aftermarket tint film, confirm whether film was applied over clear glass or whether the vehicle used privacy glass so you do not end up too light or too dark after rear windshield replacement. Finally, verify markings and fit. Automotive glass carries DOT identification and AS markings (AS2/AS3 are common on rear and side glass and can indicate tinted variations). VIN validation and the part number help ensure proper curvature, tempered-glass performance, and an insurance-friendly repair. Bang AutoGlass verifies these details before dispatching our mobile team, and every install is backed by our lifetime workmanship warranty.
Removal and Prep Steps: Interior Protection, Pinchweld Inspection, and Bond Surface Readiness
Removal and preparation are the foundation of a leak-free rear window replacement on your Mercedes-Benz 190 E. We start with containment: seats, the rear deck, and the cargo area are covered so glass pellets and adhesive debris don't contaminate the interior. Trim, fasteners, and moldings are removed in the proper sequence to protect clips and keep the opening accessible, and defroster/antenna leads are secured so wiring isn't strained. Next, the old urethane is cut and reduced to create a stable bonding surface. Standard methods remove most cured adhesive while leaving an even base layer (about 1-2 mm) so new urethane bonds to existing urethane rather than bare metal. We inspect the pinchweld for scratches through paint, rust, contamination, or misalignment from prior repairs, then treat, prime, and seal any exposed metal because corrosion under the bond line can cause leaks and adhesion loss. Before installation, we dry-fit the replacement rear glass for your Mercedes-Benz 190 E, confirm molding and spacer condition, clean the frit and aperture, and apply the correct primer/activator with proper flash times. This prep discipline lets Bang AutoGlass set the glass evenly and deliver mobile, next-day rear glass replacement backed by a lifetime workmanship warranty.
Urethane Bonding and Minimum Drive-Away Time for Mercedes-Benz 190 E: What Controls Safe Release
The difference between "installed" and "safe" after a Mercedes-Benz 190 E rear window replacement is urethane curing. Auto glass urethane is a moisture-curing polyurethane adhesive, and each system includes Safe Drive-Away Time (SDAT) guidance tied to minimum bond strength. SDAT is controlled by the adhesive used, proper surface prep, bead size/shape, and environmental conditions like temperature and humidity. Cold or very dry air can slow cure; warm, humid conditions typically speed it up. Open-time limits also matter-urethane must be applied and the glass set within the specified window for proper wet-out and adhesion. Prep details directly affect the bond: clean, contaminant-free surfaces; correct primer/activator application; and required flash times. The urethane bead must be continuous and uniform so it compresses evenly around the perimeter, preventing thin spots that can leak or whistle. Exposed metal on the pinchweld must be protected and primed because corrosion under the bond line is a common long-term failure point. At Bang AutoGlass, most Mercedes-Benz 190 E back glass replacements take about 30-45 minutes on site, then we require at least 1 hour before safe drive-away. Drive gently, avoid slamming doors, and skip automated car washes; we'll extend cure time if conditions warrant it, backed by our lifetime workmanship warranty and help with comprehensive coverage claims.
Post-Install Verification: Defroster/Antenna Testing, Leak & Wind Noise Checks, and Documentation
After your Mercedes-Benz 190 E rear window replacement, post-install verification turns new back glass into a reliable, long-term repair. Bang AutoGlass finishes every rear windshield replacement by checking electrical features, sealing, and documentation-especially when an insurance claim under comprehensive coverage is involved. First, we reconnect and secure the rear defroster tabs and any in-glass antenna leads, ensuring connectors are fully seated and wiring is strain-relieved so liftgate or trunk movement won't tug them loose. We can confirm basic operation so you don't discover a weak connection or poor reception later. Next, we validate the seal and noise performance: we inspect molding alignment and the reveal line for even spacing, then perform a controlled perimeter water test to confirm there are no leaks. If wind noise is a concern, a short road test is the most realistic way to replicate airflow and confirm proper set-down. Finally, we document the job with an invoice, warranty record, and notes on glass features for your Mercedes-Benz 190 E (tint, defroster grid, antenna integration, and DOT markings). Observe at least a 1-hour safe drive-away time and avoid automated car washes for the first day to protect the fresh urethane seal.
Services
Service Areas
Shattered Back Window on Mercedes-Benz 190 E: A Step-by-Step Rear Glass Replacement Plan
Immediate Steps After Rear Glass Breakage on Mercedes-Benz 190 E: Safety, Visibility, and Securing the Vehicle
If the rear window on your Mercedes-Benz 190 E shatters, treat it as a safety and security issue until a professional rear window replacement is completed. If it breaks while driving, slow down, turn on hazard lights, and pull into a safe, well-lit area. Tempered back glass fractures into small cubes, but they can still cut skin and irritate eyes--avoid touching your face and keep children and pets away. With gloves and eye protection, remove only loose pieces that block visibility or could drop into the cabin. Next, protect the interior from weather and theft. Remove valuables and cover the opening with plastic sheeting or a heavy-duty bag, securing it with painter's tape or other low-tack tape. Do not slam doors or the hatch; pressure changes can dislodge remaining glass. Take photos for an insurance claim, since rear glass damage is commonly handled under comprehensive coverage. Bang AutoGlass makes Mercedes-Benz 190 E back glass replacement straightforward with fully mobile service, often as soon as next day. Most installs take about 30-45 minutes on site, then the urethane requires at least 1 hour of cure time before safe drive-away. Every job is backed by our lifetime workmanship warranty.
Cleanup Plan: Removing Shards, Vacuuming the Cabin, and Protecting Trim and Upholstery
A shattered rear window spreads sharp fragments through your Mercedes-Benz 190 E, so handle cleanup like a controlled detail job. Start with PPE: closed-toe shoes, thick gloves, and eye protection. Keep passengers out of the cabin. If possible, drape plastic sheeting over seats, the rear deck/parcel shelf, and the cargo area before you move glass so shards do not get ground into fabric. Remove the largest pieces first. Lift chunks from the frame and rear deck by hand and place them into a rigid box or thick contractor bag. Then vacuum slowly with a shop-vac or strong household vacuum and a crevice tool. Work top-down in a repeatable route: headliner edge, trim gaps, rear deck, seat seams, floor mats, carpet, and the trunk or cargo well, including the spare-tire compartment. After vacuuming, use painter's tape, packing tape wrapped sticky-side out, or a lint roller to lift fine "glass sand" from upholstery and corners; repeat until the tape comes back clean. Finish with gentle vacuum passes and a slightly damp microfiber towel on plastics to avoid scratches. Leave the opening accessible so a mobile rear window replacement can be installed cleanly and securely.
Confirm the Correct Rear Glass for Mercedes-Benz 190 E: Defroster Grid, Antenna Lines, Tint, and DOT Markings
Ordering the rear glass for a Mercedes-Benz 190 E starts with matching the vehicle's options. Begin with the rear defroster: most Mercedes-Benz 190 E back windows use a printed heating grid, and the replacement must match the layout and have the connector tabs so it plugs into the factory harness. Also confirm antenna features. Many vehicles integrate AM/FM, GPS, or cellular traces into the rear window; if your reception depended on the original glass, you need an antenna-equipped replacement. Next, match tint and privacy shading. Rear glass may be clear, lightly tinted, or privacy glass. Matching shade matters for appearance, heat rejection, and (by state) compliance. If your Mercedes-Benz 190 E had aftermarket tint film, confirm whether film was applied over clear glass or whether the vehicle used privacy glass so you do not end up too light or too dark after rear windshield replacement. Finally, verify markings and fit. Automotive glass carries DOT identification and AS markings (AS2/AS3 are common on rear and side glass and can indicate tinted variations). VIN validation and the part number help ensure proper curvature, tempered-glass performance, and an insurance-friendly repair. Bang AutoGlass verifies these details before dispatching our mobile team, and every install is backed by our lifetime workmanship warranty.
Removal and Prep Steps: Interior Protection, Pinchweld Inspection, and Bond Surface Readiness
Removal and preparation are the foundation of a leak-free rear window replacement on your Mercedes-Benz 190 E. We start with containment: seats, the rear deck, and the cargo area are covered so glass pellets and adhesive debris don't contaminate the interior. Trim, fasteners, and moldings are removed in the proper sequence to protect clips and keep the opening accessible, and defroster/antenna leads are secured so wiring isn't strained. Next, the old urethane is cut and reduced to create a stable bonding surface. Standard methods remove most cured adhesive while leaving an even base layer (about 1-2 mm) so new urethane bonds to existing urethane rather than bare metal. We inspect the pinchweld for scratches through paint, rust, contamination, or misalignment from prior repairs, then treat, prime, and seal any exposed metal because corrosion under the bond line can cause leaks and adhesion loss. Before installation, we dry-fit the replacement rear glass for your Mercedes-Benz 190 E, confirm molding and spacer condition, clean the frit and aperture, and apply the correct primer/activator with proper flash times. This prep discipline lets Bang AutoGlass set the glass evenly and deliver mobile, next-day rear glass replacement backed by a lifetime workmanship warranty.
Urethane Bonding and Minimum Drive-Away Time for Mercedes-Benz 190 E: What Controls Safe Release
The difference between "installed" and "safe" after a Mercedes-Benz 190 E rear window replacement is urethane curing. Auto glass urethane is a moisture-curing polyurethane adhesive, and each system includes Safe Drive-Away Time (SDAT) guidance tied to minimum bond strength. SDAT is controlled by the adhesive used, proper surface prep, bead size/shape, and environmental conditions like temperature and humidity. Cold or very dry air can slow cure; warm, humid conditions typically speed it up. Open-time limits also matter-urethane must be applied and the glass set within the specified window for proper wet-out and adhesion. Prep details directly affect the bond: clean, contaminant-free surfaces; correct primer/activator application; and required flash times. The urethane bead must be continuous and uniform so it compresses evenly around the perimeter, preventing thin spots that can leak or whistle. Exposed metal on the pinchweld must be protected and primed because corrosion under the bond line is a common long-term failure point. At Bang AutoGlass, most Mercedes-Benz 190 E back glass replacements take about 30-45 minutes on site, then we require at least 1 hour before safe drive-away. Drive gently, avoid slamming doors, and skip automated car washes; we'll extend cure time if conditions warrant it, backed by our lifetime workmanship warranty and help with comprehensive coverage claims.
Post-Install Verification: Defroster/Antenna Testing, Leak & Wind Noise Checks, and Documentation
After your Mercedes-Benz 190 E rear window replacement, post-install verification turns new back glass into a reliable, long-term repair. Bang AutoGlass finishes every rear windshield replacement by checking electrical features, sealing, and documentation-especially when an insurance claim under comprehensive coverage is involved. First, we reconnect and secure the rear defroster tabs and any in-glass antenna leads, ensuring connectors are fully seated and wiring is strain-relieved so liftgate or trunk movement won't tug them loose. We can confirm basic operation so you don't discover a weak connection or poor reception later. Next, we validate the seal and noise performance: we inspect molding alignment and the reveal line for even spacing, then perform a controlled perimeter water test to confirm there are no leaks. If wind noise is a concern, a short road test is the most realistic way to replicate airflow and confirm proper set-down. Finally, we document the job with an invoice, warranty record, and notes on glass features for your Mercedes-Benz 190 E (tint, defroster grid, antenna integration, and DOT markings). Observe at least a 1-hour safe drive-away time and avoid automated car washes for the first day to protect the fresh urethane seal.
Enjoy More Relevant Blogs
How to Schedule Mobile Rear Glass Replacement for Mercedes-Benz 190 E
Schedule mobile rear glass replacement for your Mercedes-Benz 190 E in minutes. Learn what info to provide, how long it takes, and prep tips for service day.
How Long Does Rear Glass Replacement Take on Mercedes-Benz 190 E? Install Time, Adhesive Cure Time, and When It’s Safe to Drive
How long is Mercedes-Benz 190 E rear glass replacement? Get install time, urethane cure guidelines, and drive-away timing after service. Plan your visit today.
OEM-Quality Rear Glass Replacement for Mercedes-Benz 190 E: Defroster Grid and Tint-Match Checklist
OEM-quality rear glass replacement for Mercedes-Benz 190 E: defroster grid and tint-match checklist, plus install tips to avoid callbacks—schedule service.
Post-Install Checks for Mercedes-Benz 190 E: Rear Glass Replacement Wind Noise, Leaks, and Rattle Tests
Post-install rear glass checks for Mercedes-Benz 190 E: test for wind noise, leaks, and rattles, plus when to return for warranty service—check today before trips.
Rear Glass Replacement for Mercedes-Benz 190 E: What to Expect During Install and Aftercare
Rear glass replacement for Mercedes-Benz 190 E: what happens during install, defroster and tint considerations, cure time, and aftercare to prevent leaks long-term.
Tempered Safety Rear Glass Replacement for Mercedes-Benz 190 E: Understanding DOT Markings and FMVSS 205
Need Mercedes-Benz 190 E rear glass replacement? Learn tempered safety glass basics, DOT markings, and FMVSS 205, plus install and cure tips. Get a quote today.
Rear Defroster Not Working on Mercedes-Benz 190 E? When Rear Glass Replacement Makes More Sense Than Repair
Rear defroster not working on your Mercedes-Benz 190 E? Learn common causes, when repair fails, and when rear glass replacement is the smarter fix for winter.
How Much Does Rear Glass Replacement Cost for Mercedes-Benz 190 E? Pricing Factors, OEM vs Aftermarket, and Insurance Deductibles
Estimate Mercedes-Benz 190 E rear glass replacement cost. Compare OEM vs aftermarket, labor factors, insurance deductibles, and ways to save. Request a quote.
Back Glass Replacement on Mercedes-Benz 190 E: Defroster Tabs, Antenna Lines, and Connector Reattachment Basics
Back glass replacement on Mercedes-Benz 190 E: defroster tabs, antenna lines, and connectors explained, plus install tips to avoid damage and rework safely.
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm