Services
Service Areas
How Long Does Rear Glass Replacement Take on Mercedes-Benz Cl-Class? Install Time, Adhesive Cure Time, and When It’s Safe to Drive
How Long Does Mercedes-Benz Cl-Class Rear Glass Replacement Take? Typical Shop vs Mobile Timeline
How long a Mercedes-Benz Cl-Class rear window replacement takes depends on what you count as “time.” The in-shop installation may only require 1–3 hours of labor, but the full experience often includes booking delays, glass sourcing, drop-off and pickup, and the adhesive set period after the new back glass is installed. Technicians must remove the damaged rear windshield, clean out fragments, prep the pinch weld, and set the new rear glass in fresh urethane with careful alignment—so even a “quick” replacement can consume most of a day. Bang AutoGlass is designed to reduce that friction with mobile service at your home, office, or driveway. On most Mercedes-Benz Cl-Class back glass replacements, the hands-on phase (removal, prep, install, and cleanup) typically runs about 30–45 minutes. We then require at least 1 hour of stationary time before driving so the urethane reaches a safe initial bond. For planning purposes, many customers reserve a 90–120 minute window from arrival to safe drive-away. If you’re filing a claim, rear glass replacement is usually handled through comprehensive coverage, and we work with all carriers that provide it. We also include a lifetime workmanship warranty to back the seal and fit over time.
Mercedes-Benz Cl-Class Rear Window Replacement Install Time: Removal, Prep, Cleanup, and Set
A Mercedes-Benz Cl-Class rear glass replacement is fast only when the technician follows a disciplined process. We begin by protecting the interior and gaining access: trim, moldings, and any fasteners are removed, and defroster or antenna connections to the back glass are identified and disconnected. If the window broke, we remove loose shards and vacuum the rear deck/cargo area and vents to limit leftover glass chips. The critical step is pinch-weld preparation. Old urethane is trimmed to the correct height, the surface is cleaned and decontaminated, and any corrosion is treated so the new bead bonds evenly. When the adhesive system calls for it, primer/activator is applied to improve adhesion and reduce rust risk. Fresh automotive urethane is applied in a continuous bead, then the new rear windshield/back glass is set and aligned so the perimeter seats uniformly. Final work includes reinstalling moldings, reconnecting the defroster, using retention tape if required, and inspecting for obvious gaps that can cause leaks or wind noise. At Bang AutoGlass, most Mercedes-Benz Cl-Class back glass installs take about 30–45 minutes of hands-on work, followed by the required stationary set time before you drive.
Urethane Cure Time for Mercedes-Benz Cl-Class Back Glass: Safe Drive-Away Time (SDAT/MDAT) Explained
Urethane set and cure time is why a Mercedes-Benz Cl-Class back glass replacement isn’t “done” the moment the new rear window looks aligned. Rear glass is bonded with structural automotive urethane that must reach a safety threshold before the vehicle is driven. You may hear two terms: SDAT (Safe Drive-Away Time) and MDAT (Minimum Drive-Away Time). Both describe the minimum stationary time required after installation so the adhesive achieves safe early retention. Hitting SDAT/MDAT does not mean the urethane is fully cured; it continues gaining strength for hours as the chemistry finishes. Drive-away time varies by adhesive brand and formula, and by conditions such as temperature and humidity—cold or very dry air can slow curing, while certain fast-cure systems can shorten the window under ideal conditions. A professional installer should follow the urethane manufacturer’s product data sheet for the specific product used and provide a clear recommendation for your vehicle and environment. For customer planning, Bang AutoGlass uses a straightforward, conservative baseline for Mercedes-Benz Cl-Class rear glass replacement: keep the vehicle parked for at least 1 hour before it’s safe to drive. This helps protect the fresh bond, supports proper sealing, and reduces the risk of movement that can cause leaks or wind noise.
What Affects Mercedes-Benz Cl-Class Rear Windshield Cure Time: Temperature, Humidity, Adhesive Type, and Glass Size
Cure time for a Mercedes-Benz Cl-Class rear window replacement isn’t a single fixed number. The urethane must reach its minimum bond threshold (MDAT/SDAT) before the vehicle should be driven, and that threshold shifts with the adhesive system and the environment. Cooler temperatures generally slow moisture-cure chemistry, and low humidity can slow it further because the urethane needs ambient moisture to build strength. Warm conditions often help cure faster, but very hot, dry days can reduce open time and change how the bead handles during installation. That’s why adhesive selection matters: fast-cure urethanes are formulated to hit drive-away targets sooner within defined ranges, while conventional products may require longer stationary time; specialty systems may be chosen when temperatures are extremely low. The size and shape of the glass also influences outcomes. Bigger rear windshields/back glass—common on hatchbacks and SUVs—have more surface area and leverage, so consistent bead height, correct primers, and meticulous pinch-weld preparation are essential for even compression and sealing. Rust, old urethane high spots, oils, or dust can undermine adhesion and demand extra prep. Bang AutoGlass evaluates conditions on site for your Mercedes-Benz Cl-Class, chooses the right materials, and gives you a simple, vehicle-specific drive-away plan.
When Is It Safe to Drive After Mercedes-Benz Cl-Class Rear Glass Replacement? Practical Drive-Away Rules
Safe drive-away after a Mercedes-Benz Cl-Class rear glass replacement is determined by MDAT/SDAT—the minimum time the urethane must sit undisturbed to reach enough early strength for normal driving. Those times are not universal. They depend on the exact urethane product and on temperature and humidity during the install, so reputable technicians reference the adhesive manufacturer’s product data sheet instead of guessing. Under favorable conditions, some fast-cure systems can reach drive-away strength sooner, but cold or dry weather often extends the required wait; extreme heat can also alter working time and cure performance. For scheduling, treat the first hour as protected time. Bang AutoGlass requires at least 1 hour with your Mercedes-Benz Cl-Class parked after the back glass is installed before it is safe to drive. Don’t move it around a lot, don’t “creep it forward,” and don’t run quick errands. Once you’re cleared, take it easy for the rest of the day: avoid potholes and rough roads, close doors and the liftgate gently, and skip high-speed driving until the bond continues to mature. Insurance claims for rear window replacement are typically comprehensive, and every job is covered by our lifetime workmanship warranty.
Mercedes-Benz Cl-Class Rear Glass Aftercare Timeline: Tape, No-Car-Wash Window, Leak Checks, and Rear Defroster Tips
After a Mercedes-Benz Cl-Class rear glass replacement, good aftercare protects the fresh urethane bond while it continues curing. First, follow the drive-away time you’re given; Bang AutoGlass requires at least 1 hour of stationary time before driving. If retention tape is applied, leave it in place—its job is to stabilize the back glass and keep moldings aligned while the urethane sets. A common guideline is about 24 hours (sometimes up to 48 hours) before removing tape. For the first 24–48 hours, avoid automated car washes, pressure washing, or directing high-pressure water at the window perimeter, since force and chemicals can disturb an immature seal. Use gentle habits early on: close doors and the liftgate softly to reduce cabin-pressure spikes, and avoid rough construction roads that twist the body and load the new glass. After your first drive or first rain, do a quick leak/wind-noise check around trim and the cargo area, and call promptly if anything seems off. Finally, protect the rear defroster grid—clean inside glass with a soft microfiber cloth and mild cleaner, avoiding razors or abrasive pads.
Services
Service Areas
How Long Does Rear Glass Replacement Take on Mercedes-Benz Cl-Class? Install Time, Adhesive Cure Time, and When It’s Safe to Drive
How Long Does Mercedes-Benz Cl-Class Rear Glass Replacement Take? Typical Shop vs Mobile Timeline
How long a Mercedes-Benz Cl-Class rear window replacement takes depends on what you count as “time.” The in-shop installation may only require 1–3 hours of labor, but the full experience often includes booking delays, glass sourcing, drop-off and pickup, and the adhesive set period after the new back glass is installed. Technicians must remove the damaged rear windshield, clean out fragments, prep the pinch weld, and set the new rear glass in fresh urethane with careful alignment—so even a “quick” replacement can consume most of a day. Bang AutoGlass is designed to reduce that friction with mobile service at your home, office, or driveway. On most Mercedes-Benz Cl-Class back glass replacements, the hands-on phase (removal, prep, install, and cleanup) typically runs about 30–45 minutes. We then require at least 1 hour of stationary time before driving so the urethane reaches a safe initial bond. For planning purposes, many customers reserve a 90–120 minute window from arrival to safe drive-away. If you’re filing a claim, rear glass replacement is usually handled through comprehensive coverage, and we work with all carriers that provide it. We also include a lifetime workmanship warranty to back the seal and fit over time.
Mercedes-Benz Cl-Class Rear Window Replacement Install Time: Removal, Prep, Cleanup, and Set
A Mercedes-Benz Cl-Class rear glass replacement is fast only when the technician follows a disciplined process. We begin by protecting the interior and gaining access: trim, moldings, and any fasteners are removed, and defroster or antenna connections to the back glass are identified and disconnected. If the window broke, we remove loose shards and vacuum the rear deck/cargo area and vents to limit leftover glass chips. The critical step is pinch-weld preparation. Old urethane is trimmed to the correct height, the surface is cleaned and decontaminated, and any corrosion is treated so the new bead bonds evenly. When the adhesive system calls for it, primer/activator is applied to improve adhesion and reduce rust risk. Fresh automotive urethane is applied in a continuous bead, then the new rear windshield/back glass is set and aligned so the perimeter seats uniformly. Final work includes reinstalling moldings, reconnecting the defroster, using retention tape if required, and inspecting for obvious gaps that can cause leaks or wind noise. At Bang AutoGlass, most Mercedes-Benz Cl-Class back glass installs take about 30–45 minutes of hands-on work, followed by the required stationary set time before you drive.
Urethane Cure Time for Mercedes-Benz Cl-Class Back Glass: Safe Drive-Away Time (SDAT/MDAT) Explained
Urethane set and cure time is why a Mercedes-Benz Cl-Class back glass replacement isn’t “done” the moment the new rear window looks aligned. Rear glass is bonded with structural automotive urethane that must reach a safety threshold before the vehicle is driven. You may hear two terms: SDAT (Safe Drive-Away Time) and MDAT (Minimum Drive-Away Time). Both describe the minimum stationary time required after installation so the adhesive achieves safe early retention. Hitting SDAT/MDAT does not mean the urethane is fully cured; it continues gaining strength for hours as the chemistry finishes. Drive-away time varies by adhesive brand and formula, and by conditions such as temperature and humidity—cold or very dry air can slow curing, while certain fast-cure systems can shorten the window under ideal conditions. A professional installer should follow the urethane manufacturer’s product data sheet for the specific product used and provide a clear recommendation for your vehicle and environment. For customer planning, Bang AutoGlass uses a straightforward, conservative baseline for Mercedes-Benz Cl-Class rear glass replacement: keep the vehicle parked for at least 1 hour before it’s safe to drive. This helps protect the fresh bond, supports proper sealing, and reduces the risk of movement that can cause leaks or wind noise.
What Affects Mercedes-Benz Cl-Class Rear Windshield Cure Time: Temperature, Humidity, Adhesive Type, and Glass Size
Cure time for a Mercedes-Benz Cl-Class rear window replacement isn’t a single fixed number. The urethane must reach its minimum bond threshold (MDAT/SDAT) before the vehicle should be driven, and that threshold shifts with the adhesive system and the environment. Cooler temperatures generally slow moisture-cure chemistry, and low humidity can slow it further because the urethane needs ambient moisture to build strength. Warm conditions often help cure faster, but very hot, dry days can reduce open time and change how the bead handles during installation. That’s why adhesive selection matters: fast-cure urethanes are formulated to hit drive-away targets sooner within defined ranges, while conventional products may require longer stationary time; specialty systems may be chosen when temperatures are extremely low. The size and shape of the glass also influences outcomes. Bigger rear windshields/back glass—common on hatchbacks and SUVs—have more surface area and leverage, so consistent bead height, correct primers, and meticulous pinch-weld preparation are essential for even compression and sealing. Rust, old urethane high spots, oils, or dust can undermine adhesion and demand extra prep. Bang AutoGlass evaluates conditions on site for your Mercedes-Benz Cl-Class, chooses the right materials, and gives you a simple, vehicle-specific drive-away plan.
When Is It Safe to Drive After Mercedes-Benz Cl-Class Rear Glass Replacement? Practical Drive-Away Rules
Safe drive-away after a Mercedes-Benz Cl-Class rear glass replacement is determined by MDAT/SDAT—the minimum time the urethane must sit undisturbed to reach enough early strength for normal driving. Those times are not universal. They depend on the exact urethane product and on temperature and humidity during the install, so reputable technicians reference the adhesive manufacturer’s product data sheet instead of guessing. Under favorable conditions, some fast-cure systems can reach drive-away strength sooner, but cold or dry weather often extends the required wait; extreme heat can also alter working time and cure performance. For scheduling, treat the first hour as protected time. Bang AutoGlass requires at least 1 hour with your Mercedes-Benz Cl-Class parked after the back glass is installed before it is safe to drive. Don’t move it around a lot, don’t “creep it forward,” and don’t run quick errands. Once you’re cleared, take it easy for the rest of the day: avoid potholes and rough roads, close doors and the liftgate gently, and skip high-speed driving until the bond continues to mature. Insurance claims for rear window replacement are typically comprehensive, and every job is covered by our lifetime workmanship warranty.
Mercedes-Benz Cl-Class Rear Glass Aftercare Timeline: Tape, No-Car-Wash Window, Leak Checks, and Rear Defroster Tips
After a Mercedes-Benz Cl-Class rear glass replacement, good aftercare protects the fresh urethane bond while it continues curing. First, follow the drive-away time you’re given; Bang AutoGlass requires at least 1 hour of stationary time before driving. If retention tape is applied, leave it in place—its job is to stabilize the back glass and keep moldings aligned while the urethane sets. A common guideline is about 24 hours (sometimes up to 48 hours) before removing tape. For the first 24–48 hours, avoid automated car washes, pressure washing, or directing high-pressure water at the window perimeter, since force and chemicals can disturb an immature seal. Use gentle habits early on: close doors and the liftgate softly to reduce cabin-pressure spikes, and avoid rough construction roads that twist the body and load the new glass. After your first drive or first rain, do a quick leak/wind-noise check around trim and the cargo area, and call promptly if anything seems off. Finally, protect the rear defroster grid—clean inside glass with a soft microfiber cloth and mild cleaner, avoiding razors or abrasive pads.
Services
Service Areas
How Long Does Rear Glass Replacement Take on Mercedes-Benz Cl-Class? Install Time, Adhesive Cure Time, and When It’s Safe to Drive
How Long Does Mercedes-Benz Cl-Class Rear Glass Replacement Take? Typical Shop vs Mobile Timeline
How long a Mercedes-Benz Cl-Class rear window replacement takes depends on what you count as “time.” The in-shop installation may only require 1–3 hours of labor, but the full experience often includes booking delays, glass sourcing, drop-off and pickup, and the adhesive set period after the new back glass is installed. Technicians must remove the damaged rear windshield, clean out fragments, prep the pinch weld, and set the new rear glass in fresh urethane with careful alignment—so even a “quick” replacement can consume most of a day. Bang AutoGlass is designed to reduce that friction with mobile service at your home, office, or driveway. On most Mercedes-Benz Cl-Class back glass replacements, the hands-on phase (removal, prep, install, and cleanup) typically runs about 30–45 minutes. We then require at least 1 hour of stationary time before driving so the urethane reaches a safe initial bond. For planning purposes, many customers reserve a 90–120 minute window from arrival to safe drive-away. If you’re filing a claim, rear glass replacement is usually handled through comprehensive coverage, and we work with all carriers that provide it. We also include a lifetime workmanship warranty to back the seal and fit over time.
Mercedes-Benz Cl-Class Rear Window Replacement Install Time: Removal, Prep, Cleanup, and Set
A Mercedes-Benz Cl-Class rear glass replacement is fast only when the technician follows a disciplined process. We begin by protecting the interior and gaining access: trim, moldings, and any fasteners are removed, and defroster or antenna connections to the back glass are identified and disconnected. If the window broke, we remove loose shards and vacuum the rear deck/cargo area and vents to limit leftover glass chips. The critical step is pinch-weld preparation. Old urethane is trimmed to the correct height, the surface is cleaned and decontaminated, and any corrosion is treated so the new bead bonds evenly. When the adhesive system calls for it, primer/activator is applied to improve adhesion and reduce rust risk. Fresh automotive urethane is applied in a continuous bead, then the new rear windshield/back glass is set and aligned so the perimeter seats uniformly. Final work includes reinstalling moldings, reconnecting the defroster, using retention tape if required, and inspecting for obvious gaps that can cause leaks or wind noise. At Bang AutoGlass, most Mercedes-Benz Cl-Class back glass installs take about 30–45 minutes of hands-on work, followed by the required stationary set time before you drive.
Urethane Cure Time for Mercedes-Benz Cl-Class Back Glass: Safe Drive-Away Time (SDAT/MDAT) Explained
Urethane set and cure time is why a Mercedes-Benz Cl-Class back glass replacement isn’t “done” the moment the new rear window looks aligned. Rear glass is bonded with structural automotive urethane that must reach a safety threshold before the vehicle is driven. You may hear two terms: SDAT (Safe Drive-Away Time) and MDAT (Minimum Drive-Away Time). Both describe the minimum stationary time required after installation so the adhesive achieves safe early retention. Hitting SDAT/MDAT does not mean the urethane is fully cured; it continues gaining strength for hours as the chemistry finishes. Drive-away time varies by adhesive brand and formula, and by conditions such as temperature and humidity—cold or very dry air can slow curing, while certain fast-cure systems can shorten the window under ideal conditions. A professional installer should follow the urethane manufacturer’s product data sheet for the specific product used and provide a clear recommendation for your vehicle and environment. For customer planning, Bang AutoGlass uses a straightforward, conservative baseline for Mercedes-Benz Cl-Class rear glass replacement: keep the vehicle parked for at least 1 hour before it’s safe to drive. This helps protect the fresh bond, supports proper sealing, and reduces the risk of movement that can cause leaks or wind noise.
What Affects Mercedes-Benz Cl-Class Rear Windshield Cure Time: Temperature, Humidity, Adhesive Type, and Glass Size
Cure time for a Mercedes-Benz Cl-Class rear window replacement isn’t a single fixed number. The urethane must reach its minimum bond threshold (MDAT/SDAT) before the vehicle should be driven, and that threshold shifts with the adhesive system and the environment. Cooler temperatures generally slow moisture-cure chemistry, and low humidity can slow it further because the urethane needs ambient moisture to build strength. Warm conditions often help cure faster, but very hot, dry days can reduce open time and change how the bead handles during installation. That’s why adhesive selection matters: fast-cure urethanes are formulated to hit drive-away targets sooner within defined ranges, while conventional products may require longer stationary time; specialty systems may be chosen when temperatures are extremely low. The size and shape of the glass also influences outcomes. Bigger rear windshields/back glass—common on hatchbacks and SUVs—have more surface area and leverage, so consistent bead height, correct primers, and meticulous pinch-weld preparation are essential for even compression and sealing. Rust, old urethane high spots, oils, or dust can undermine adhesion and demand extra prep. Bang AutoGlass evaluates conditions on site for your Mercedes-Benz Cl-Class, chooses the right materials, and gives you a simple, vehicle-specific drive-away plan.
When Is It Safe to Drive After Mercedes-Benz Cl-Class Rear Glass Replacement? Practical Drive-Away Rules
Safe drive-away after a Mercedes-Benz Cl-Class rear glass replacement is determined by MDAT/SDAT—the minimum time the urethane must sit undisturbed to reach enough early strength for normal driving. Those times are not universal. They depend on the exact urethane product and on temperature and humidity during the install, so reputable technicians reference the adhesive manufacturer’s product data sheet instead of guessing. Under favorable conditions, some fast-cure systems can reach drive-away strength sooner, but cold or dry weather often extends the required wait; extreme heat can also alter working time and cure performance. For scheduling, treat the first hour as protected time. Bang AutoGlass requires at least 1 hour with your Mercedes-Benz Cl-Class parked after the back glass is installed before it is safe to drive. Don’t move it around a lot, don’t “creep it forward,” and don’t run quick errands. Once you’re cleared, take it easy for the rest of the day: avoid potholes and rough roads, close doors and the liftgate gently, and skip high-speed driving until the bond continues to mature. Insurance claims for rear window replacement are typically comprehensive, and every job is covered by our lifetime workmanship warranty.
Mercedes-Benz Cl-Class Rear Glass Aftercare Timeline: Tape, No-Car-Wash Window, Leak Checks, and Rear Defroster Tips
After a Mercedes-Benz Cl-Class rear glass replacement, good aftercare protects the fresh urethane bond while it continues curing. First, follow the drive-away time you’re given; Bang AutoGlass requires at least 1 hour of stationary time before driving. If retention tape is applied, leave it in place—its job is to stabilize the back glass and keep moldings aligned while the urethane sets. A common guideline is about 24 hours (sometimes up to 48 hours) before removing tape. For the first 24–48 hours, avoid automated car washes, pressure washing, or directing high-pressure water at the window perimeter, since force and chemicals can disturb an immature seal. Use gentle habits early on: close doors and the liftgate softly to reduce cabin-pressure spikes, and avoid rough construction roads that twist the body and load the new glass. After your first drive or first rain, do a quick leak/wind-noise check around trim and the cargo area, and call promptly if anything seems off. Finally, protect the rear defroster grid—clean inside glass with a soft microfiber cloth and mild cleaner, avoiding razors or abrasive pads.
Enjoy More Relevant Blogs
Rear Defroster Not Working on Mercedes-Benz Cl-Class? When Rear Glass Replacement Makes More Sense Than Repair
Rear defroster not working on your Mercedes-Benz Cl-Class? Learn common causes, when repair fails, and when rear glass replacement is the smarter fix for winter.
How to Schedule Mobile Rear Glass Replacement for Mercedes-Benz Cl-Class
Schedule mobile rear glass replacement for your Mercedes-Benz Cl-Class in minutes. Learn what info to provide, how long it takes, and prep tips for service day.
OEM-Quality Rear Glass Replacement for Mercedes-Benz Cl-Class: Defroster Grid and Tint-Match Checklist
OEM-quality rear glass replacement for Mercedes-Benz Cl-Class: defroster grid and tint-match checklist, plus install tips to avoid callbacks—schedule service.
Rear Glass Replacement for Mercedes-Benz Cl-Class: What to Expect During Install and Aftercare
Rear glass replacement for Mercedes-Benz Cl-Class: what happens during install, defroster and tint considerations, cure time, and aftercare to prevent leaks long-term.
How Much Does Rear Glass Replacement Cost for Mercedes-Benz Cl-Class? Pricing Factors, OEM vs Aftermarket, and Insurance Deductibles
Estimate Mercedes-Benz Cl-Class rear glass replacement cost. Compare OEM vs aftermarket, labor factors, insurance deductibles, and ways to save. Request a quote.
Post-Install Checks for Mercedes-Benz Cl-Class: Rear Glass Replacement Wind Noise, Leaks, and Rattle Tests
Post-install rear glass checks for Mercedes-Benz Cl-Class: test for wind noise, leaks, and rattles, plus when to return for warranty service—check today before trips.
Back Glass Replacement on Mercedes-Benz Cl-Class: Defroster Tabs, Antenna Lines, and Connector Reattachment Basics
Back glass replacement on Mercedes-Benz Cl-Class: defroster tabs, antenna lines, and connectors explained, plus install tips to avoid damage and rework safely.
Shattered Back Window on Mercedes-Benz Cl-Class: A Step-by-Step Rear Glass Replacement Plan
Shattered back window on Mercedes-Benz Cl-Class? Follow a step-by-step rear glass replacement plan, cleanup tips, defroster notes, cure time, and drive-away rules.
Tempered Safety Rear Glass Replacement for Mercedes-Benz Cl-Class: Understanding DOT Markings and FMVSS 205
Need Mercedes-Benz Cl-Class rear glass replacement? Learn tempered safety glass basics, DOT markings, and FMVSS 205, plus install and cure tips. Get a quote today.
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm