Services
Service Areas
ADAS Warning Lights on Mitsubishi Colt: When Calibration Is the Fix and When It’s Not
ADAS Warning Lights on Mitsubishi Colt: What the Icons and Messages Commonly Indicate
ADAS warning lights on your Mitsubishi Colt mean a driver-assist feature is limited, temporarily disabled, or needs service. The icon often indicates the system: a car between lane lines is Lane Keep Assist/Lane Departure Warning, an “impact” symbol points to Forward Collision Warning or Automatic Emergency Braking, and a speedometer/cruise icon commonly relates to Adaptive Cruise Control. Messages such as “Driver Assist Limited,” “Camera Obscured,” “Front Radar Blocked,” or “ACC Unavailable” usually mean a sensor cannot see clearly enough or the system failed a self-check. Start with the basics. Clean the windshield around the forward camera near the rearview mirror (inside and out), clear frost or fog, and confirm wipers and washer fluid work without streaks. Up front, wipe the radar cover or emblem area and remove bugs, mud, or snow. If the warning started after a rock chip, crack, windshield replacement, or a minor front-end tap, the camera bracket or sensor alignment may be out of tolerance and calibration may be required. Bang AutoGlass offers mobile windshield replacement as soon as next day. Most installs take 30–45 minutes, plus at least 1 hour of safe drive-away time, with a lifetime workmanship warranty and insurance help.
When Calibration Is the Fix for Mitsubishi Colt: Post-Windshield Replacement and Sensor Alignment Triggers
Calibration on a Mitsubishi Colt is an aiming and reference reset. The forward camera and radar must agree on where “straight ahead” is so the software can judge lanes, closing distance, and object position. That’s why calibration is most commonly needed after a windshield replacement, camera bracket service, or front-end work that required removing and reinstalling the radar. Even small shifts in bracket angle, fastener torque, or windshield specification can trigger “ACC Unavailable,” “Driver Assist Limited,” or “Calibration Required” and keep features offline. A second group of triggers involves geometry changes that move the baseline the modules expect. Alignment adjustments, suspension or ride-height changes, steering repairs, and non-OEM tire sizing can invalidate prior calibration data. A clean workflow reduces comebacks: document DTCs with a pre-scan, verify the correct windshield for the Mitsubishi Colt, inspect the camera mount and radar cover, confirm stable battery voltage and tire pressures, run the required static targets and/or dynamic road learning, then complete a post-scan to confirm everything is clear. Bang AutoGlass can handle the glass portion with mobile next-day service and a lifetime workmanship warranty.
When It’s Not Calibration on Mitsubishi Colt: Obstructions, Damage, Voltage, Wiring, and Module Faults
On a Mitsubishi Colt, an ADAS warning light does not automatically mean calibration is needed. Many systems pause whenever sensor input is unreliable. Weather and road conditions are common causes: heavy rain, snow, fog, glare, or road spray can reduce camera contrast and prevent tracking of lane markings or vehicles, leading to “Camera Obscured” or “Driver Assist Limited.” Features often return once visibility improves. Obstructions and add-ons can create the same symptoms. Dashcams, toll tags, stickers, and poorly placed tint near the camera window can block the forward view. Up front, a cracked, misaligned, or painted radar cover/emblem can interrupt the signal and trigger “Front Radar Blocked” or “ACC Unavailable.” Electrical stability matters, too: a weak 12-volt battery or recent battery disconnect can set low-voltage or communication faults that take modules offline. If warnings persist after cleaning, treat it as diagnostics. A DTC scan helps distinguish a blocked sensor from fuse, ground, connector, corrosion, harness, camera/radar unit, or software issues. If the warning began after windshield damage, replacement, or a front-end impact, Bang AutoGlass can inspect the glass and camera area; we’re mobile as soon as next day and back our work with a lifetime workmanship warranty.
Diagnostic Scan Workflow for Mitsubishi Colt: Reading DTCs, Root-Cause Checks, and OEM Procedures
On a modern Mitsubishi Colt, clearing ADAS warning lights starts with scan data, not parts swapping. The dash icon only tells you a system is limited; it does not identify the trigger. Many OEM procedures call for a pre-repair health scan whenever the windshield camera, front radar, ABS/steering inputs, or related wiring has been disturbed—common after windshield replacement, collision or bumper work, alignments, suspension changes, or low-voltage events. Run a pre-scan with a tool that can access ADAS, ABS, steering, and body modules. Save all DTCs (current, pending, history) and freeze-frame information before clearing anything, and use the results to confirm which driver-assist features your Mitsubishi Colt actually has. Then follow OEM service information: confirm stable battery/charging voltage, inspect fuses and grounds, and check connectors and harness routing at the camera and radar for corrosion, pin-fit issues, or strain. Verify the correct windshield specification, an intact and properly bonded camera bracket, and clean, unobstructed sensor viewing zones. Ensure prerequisites are within spec—tire size/pressure, ride height, and alignment—before attempting calibration. After corrections and any required calibration/initialization, complete a post-scan to confirm codes are resolved and do not return. Bang AutoGlass can handle mobile next-day glass service and help coordinate the OEM-required next step.
Static vs Dynamic ADAS Calibration for Mitsubishi Colt: Prerequisites, Conditions, and Limitations
Static and dynamic ADAS calibration both return your Mitsubishi Colt to OEM aiming specs, but they work differently and have strict prerequisites. Static calibration is done with the vehicle stationary in a controlled bay using OEM targets, measurements, and a scan tool to start the routine. Success typically requires a level floor, precise target distance/height, consistent lighting, correct tire pressures and tire size, normal ride height, and no active DTCs that would block the procedure. Dynamic calibration is completed on the road. The technician puts the system in learn mode with a scan tool, then drives under OEM-defined conditions—often minimum speeds, time or distance requirements, clear lane markings, and good visibility. Weather, traffic, construction zones, glare, or inconsistent lane paint can prevent learning and trigger “calibration incomplete” or “system unavailable” messages. Many Mitsubishi Colt platforms require static, dynamic, or a dual process depending on what was disturbed (camera vs radar), and some also require steering angle sensor initialization. Calibration is not a reset: if alignment is out of spec, voltage is unstable, or the camera/radar area is obstructed, the warning may return even after an attempted routine. Bang AutoGlass offers mobile next-day windshield replacement and can help you plan the required OEM calibration.
Proving the Repair Worked on Mitsubishi Colt: Post-Scan, Verification Drive, and Documentation
For ADAS-related repairs on a Mitsubishi Colt, the absence of a warning light is a good sign, but it is not a complete acceptance test. Start with a post-repair scan across all relevant modules to confirm ADAS-related DTCs are cleared and that no new network, camera, or radar faults are present. If calibration or initialization was performed, keep the completion report showing which systems were calibrated and that each routine finished successfully. Next, validate operation the way the OEM intends. When procedures call for it, perform a verification drive to confirm lane keep assist remains available without frequent dropouts, adaptive cruise control engages and holds, and forward collision warning operates normally. If “system limited” messages return during the drive, treat them as evidence of an unresolved prerequisite or root-cause issue rather than assuming calibration failed. Also verify real-world conditions that impact performance: the windshield camera area is clean and unobstructed, wipers clear without streaking, and there is no haze, distortion, or glare affecting the camera’s view. Finally, organize documentation—pre-scan, post-scan, calibration printouts, and road-test notes—for insurance, resale value, and dispute prevention. Bang AutoGlass supports mobile next-day service and backs workmanship with a lifetime warranty.
Services
Service Areas
ADAS Warning Lights on Mitsubishi Colt: When Calibration Is the Fix and When It’s Not
ADAS Warning Lights on Mitsubishi Colt: What the Icons and Messages Commonly Indicate
ADAS warning lights on your Mitsubishi Colt mean a driver-assist feature is limited, temporarily disabled, or needs service. The icon often indicates the system: a car between lane lines is Lane Keep Assist/Lane Departure Warning, an “impact” symbol points to Forward Collision Warning or Automatic Emergency Braking, and a speedometer/cruise icon commonly relates to Adaptive Cruise Control. Messages such as “Driver Assist Limited,” “Camera Obscured,” “Front Radar Blocked,” or “ACC Unavailable” usually mean a sensor cannot see clearly enough or the system failed a self-check. Start with the basics. Clean the windshield around the forward camera near the rearview mirror (inside and out), clear frost or fog, and confirm wipers and washer fluid work without streaks. Up front, wipe the radar cover or emblem area and remove bugs, mud, or snow. If the warning started after a rock chip, crack, windshield replacement, or a minor front-end tap, the camera bracket or sensor alignment may be out of tolerance and calibration may be required. Bang AutoGlass offers mobile windshield replacement as soon as next day. Most installs take 30–45 minutes, plus at least 1 hour of safe drive-away time, with a lifetime workmanship warranty and insurance help.
When Calibration Is the Fix for Mitsubishi Colt: Post-Windshield Replacement and Sensor Alignment Triggers
Calibration on a Mitsubishi Colt is an aiming and reference reset. The forward camera and radar must agree on where “straight ahead” is so the software can judge lanes, closing distance, and object position. That’s why calibration is most commonly needed after a windshield replacement, camera bracket service, or front-end work that required removing and reinstalling the radar. Even small shifts in bracket angle, fastener torque, or windshield specification can trigger “ACC Unavailable,” “Driver Assist Limited,” or “Calibration Required” and keep features offline. A second group of triggers involves geometry changes that move the baseline the modules expect. Alignment adjustments, suspension or ride-height changes, steering repairs, and non-OEM tire sizing can invalidate prior calibration data. A clean workflow reduces comebacks: document DTCs with a pre-scan, verify the correct windshield for the Mitsubishi Colt, inspect the camera mount and radar cover, confirm stable battery voltage and tire pressures, run the required static targets and/or dynamic road learning, then complete a post-scan to confirm everything is clear. Bang AutoGlass can handle the glass portion with mobile next-day service and a lifetime workmanship warranty.
When It’s Not Calibration on Mitsubishi Colt: Obstructions, Damage, Voltage, Wiring, and Module Faults
On a Mitsubishi Colt, an ADAS warning light does not automatically mean calibration is needed. Many systems pause whenever sensor input is unreliable. Weather and road conditions are common causes: heavy rain, snow, fog, glare, or road spray can reduce camera contrast and prevent tracking of lane markings or vehicles, leading to “Camera Obscured” or “Driver Assist Limited.” Features often return once visibility improves. Obstructions and add-ons can create the same symptoms. Dashcams, toll tags, stickers, and poorly placed tint near the camera window can block the forward view. Up front, a cracked, misaligned, or painted radar cover/emblem can interrupt the signal and trigger “Front Radar Blocked” or “ACC Unavailable.” Electrical stability matters, too: a weak 12-volt battery or recent battery disconnect can set low-voltage or communication faults that take modules offline. If warnings persist after cleaning, treat it as diagnostics. A DTC scan helps distinguish a blocked sensor from fuse, ground, connector, corrosion, harness, camera/radar unit, or software issues. If the warning began after windshield damage, replacement, or a front-end impact, Bang AutoGlass can inspect the glass and camera area; we’re mobile as soon as next day and back our work with a lifetime workmanship warranty.
Diagnostic Scan Workflow for Mitsubishi Colt: Reading DTCs, Root-Cause Checks, and OEM Procedures
On a modern Mitsubishi Colt, clearing ADAS warning lights starts with scan data, not parts swapping. The dash icon only tells you a system is limited; it does not identify the trigger. Many OEM procedures call for a pre-repair health scan whenever the windshield camera, front radar, ABS/steering inputs, or related wiring has been disturbed—common after windshield replacement, collision or bumper work, alignments, suspension changes, or low-voltage events. Run a pre-scan with a tool that can access ADAS, ABS, steering, and body modules. Save all DTCs (current, pending, history) and freeze-frame information before clearing anything, and use the results to confirm which driver-assist features your Mitsubishi Colt actually has. Then follow OEM service information: confirm stable battery/charging voltage, inspect fuses and grounds, and check connectors and harness routing at the camera and radar for corrosion, pin-fit issues, or strain. Verify the correct windshield specification, an intact and properly bonded camera bracket, and clean, unobstructed sensor viewing zones. Ensure prerequisites are within spec—tire size/pressure, ride height, and alignment—before attempting calibration. After corrections and any required calibration/initialization, complete a post-scan to confirm codes are resolved and do not return. Bang AutoGlass can handle mobile next-day glass service and help coordinate the OEM-required next step.
Static vs Dynamic ADAS Calibration for Mitsubishi Colt: Prerequisites, Conditions, and Limitations
Static and dynamic ADAS calibration both return your Mitsubishi Colt to OEM aiming specs, but they work differently and have strict prerequisites. Static calibration is done with the vehicle stationary in a controlled bay using OEM targets, measurements, and a scan tool to start the routine. Success typically requires a level floor, precise target distance/height, consistent lighting, correct tire pressures and tire size, normal ride height, and no active DTCs that would block the procedure. Dynamic calibration is completed on the road. The technician puts the system in learn mode with a scan tool, then drives under OEM-defined conditions—often minimum speeds, time or distance requirements, clear lane markings, and good visibility. Weather, traffic, construction zones, glare, or inconsistent lane paint can prevent learning and trigger “calibration incomplete” or “system unavailable” messages. Many Mitsubishi Colt platforms require static, dynamic, or a dual process depending on what was disturbed (camera vs radar), and some also require steering angle sensor initialization. Calibration is not a reset: if alignment is out of spec, voltage is unstable, or the camera/radar area is obstructed, the warning may return even after an attempted routine. Bang AutoGlass offers mobile next-day windshield replacement and can help you plan the required OEM calibration.
Proving the Repair Worked on Mitsubishi Colt: Post-Scan, Verification Drive, and Documentation
For ADAS-related repairs on a Mitsubishi Colt, the absence of a warning light is a good sign, but it is not a complete acceptance test. Start with a post-repair scan across all relevant modules to confirm ADAS-related DTCs are cleared and that no new network, camera, or radar faults are present. If calibration or initialization was performed, keep the completion report showing which systems were calibrated and that each routine finished successfully. Next, validate operation the way the OEM intends. When procedures call for it, perform a verification drive to confirm lane keep assist remains available without frequent dropouts, adaptive cruise control engages and holds, and forward collision warning operates normally. If “system limited” messages return during the drive, treat them as evidence of an unresolved prerequisite or root-cause issue rather than assuming calibration failed. Also verify real-world conditions that impact performance: the windshield camera area is clean and unobstructed, wipers clear without streaking, and there is no haze, distortion, or glare affecting the camera’s view. Finally, organize documentation—pre-scan, post-scan, calibration printouts, and road-test notes—for insurance, resale value, and dispute prevention. Bang AutoGlass supports mobile next-day service and backs workmanship with a lifetime warranty.
Services
Service Areas
ADAS Warning Lights on Mitsubishi Colt: When Calibration Is the Fix and When It’s Not
ADAS Warning Lights on Mitsubishi Colt: What the Icons and Messages Commonly Indicate
ADAS warning lights on your Mitsubishi Colt mean a driver-assist feature is limited, temporarily disabled, or needs service. The icon often indicates the system: a car between lane lines is Lane Keep Assist/Lane Departure Warning, an “impact” symbol points to Forward Collision Warning or Automatic Emergency Braking, and a speedometer/cruise icon commonly relates to Adaptive Cruise Control. Messages such as “Driver Assist Limited,” “Camera Obscured,” “Front Radar Blocked,” or “ACC Unavailable” usually mean a sensor cannot see clearly enough or the system failed a self-check. Start with the basics. Clean the windshield around the forward camera near the rearview mirror (inside and out), clear frost or fog, and confirm wipers and washer fluid work without streaks. Up front, wipe the radar cover or emblem area and remove bugs, mud, or snow. If the warning started after a rock chip, crack, windshield replacement, or a minor front-end tap, the camera bracket or sensor alignment may be out of tolerance and calibration may be required. Bang AutoGlass offers mobile windshield replacement as soon as next day. Most installs take 30–45 minutes, plus at least 1 hour of safe drive-away time, with a lifetime workmanship warranty and insurance help.
When Calibration Is the Fix for Mitsubishi Colt: Post-Windshield Replacement and Sensor Alignment Triggers
Calibration on a Mitsubishi Colt is an aiming and reference reset. The forward camera and radar must agree on where “straight ahead” is so the software can judge lanes, closing distance, and object position. That’s why calibration is most commonly needed after a windshield replacement, camera bracket service, or front-end work that required removing and reinstalling the radar. Even small shifts in bracket angle, fastener torque, or windshield specification can trigger “ACC Unavailable,” “Driver Assist Limited,” or “Calibration Required” and keep features offline. A second group of triggers involves geometry changes that move the baseline the modules expect. Alignment adjustments, suspension or ride-height changes, steering repairs, and non-OEM tire sizing can invalidate prior calibration data. A clean workflow reduces comebacks: document DTCs with a pre-scan, verify the correct windshield for the Mitsubishi Colt, inspect the camera mount and radar cover, confirm stable battery voltage and tire pressures, run the required static targets and/or dynamic road learning, then complete a post-scan to confirm everything is clear. Bang AutoGlass can handle the glass portion with mobile next-day service and a lifetime workmanship warranty.
When It’s Not Calibration on Mitsubishi Colt: Obstructions, Damage, Voltage, Wiring, and Module Faults
On a Mitsubishi Colt, an ADAS warning light does not automatically mean calibration is needed. Many systems pause whenever sensor input is unreliable. Weather and road conditions are common causes: heavy rain, snow, fog, glare, or road spray can reduce camera contrast and prevent tracking of lane markings or vehicles, leading to “Camera Obscured” or “Driver Assist Limited.” Features often return once visibility improves. Obstructions and add-ons can create the same symptoms. Dashcams, toll tags, stickers, and poorly placed tint near the camera window can block the forward view. Up front, a cracked, misaligned, or painted radar cover/emblem can interrupt the signal and trigger “Front Radar Blocked” or “ACC Unavailable.” Electrical stability matters, too: a weak 12-volt battery or recent battery disconnect can set low-voltage or communication faults that take modules offline. If warnings persist after cleaning, treat it as diagnostics. A DTC scan helps distinguish a blocked sensor from fuse, ground, connector, corrosion, harness, camera/radar unit, or software issues. If the warning began after windshield damage, replacement, or a front-end impact, Bang AutoGlass can inspect the glass and camera area; we’re mobile as soon as next day and back our work with a lifetime workmanship warranty.
Diagnostic Scan Workflow for Mitsubishi Colt: Reading DTCs, Root-Cause Checks, and OEM Procedures
On a modern Mitsubishi Colt, clearing ADAS warning lights starts with scan data, not parts swapping. The dash icon only tells you a system is limited; it does not identify the trigger. Many OEM procedures call for a pre-repair health scan whenever the windshield camera, front radar, ABS/steering inputs, or related wiring has been disturbed—common after windshield replacement, collision or bumper work, alignments, suspension changes, or low-voltage events. Run a pre-scan with a tool that can access ADAS, ABS, steering, and body modules. Save all DTCs (current, pending, history) and freeze-frame information before clearing anything, and use the results to confirm which driver-assist features your Mitsubishi Colt actually has. Then follow OEM service information: confirm stable battery/charging voltage, inspect fuses and grounds, and check connectors and harness routing at the camera and radar for corrosion, pin-fit issues, or strain. Verify the correct windshield specification, an intact and properly bonded camera bracket, and clean, unobstructed sensor viewing zones. Ensure prerequisites are within spec—tire size/pressure, ride height, and alignment—before attempting calibration. After corrections and any required calibration/initialization, complete a post-scan to confirm codes are resolved and do not return. Bang AutoGlass can handle mobile next-day glass service and help coordinate the OEM-required next step.
Static vs Dynamic ADAS Calibration for Mitsubishi Colt: Prerequisites, Conditions, and Limitations
Static and dynamic ADAS calibration both return your Mitsubishi Colt to OEM aiming specs, but they work differently and have strict prerequisites. Static calibration is done with the vehicle stationary in a controlled bay using OEM targets, measurements, and a scan tool to start the routine. Success typically requires a level floor, precise target distance/height, consistent lighting, correct tire pressures and tire size, normal ride height, and no active DTCs that would block the procedure. Dynamic calibration is completed on the road. The technician puts the system in learn mode with a scan tool, then drives under OEM-defined conditions—often minimum speeds, time or distance requirements, clear lane markings, and good visibility. Weather, traffic, construction zones, glare, or inconsistent lane paint can prevent learning and trigger “calibration incomplete” or “system unavailable” messages. Many Mitsubishi Colt platforms require static, dynamic, or a dual process depending on what was disturbed (camera vs radar), and some also require steering angle sensor initialization. Calibration is not a reset: if alignment is out of spec, voltage is unstable, or the camera/radar area is obstructed, the warning may return even after an attempted routine. Bang AutoGlass offers mobile next-day windshield replacement and can help you plan the required OEM calibration.
Proving the Repair Worked on Mitsubishi Colt: Post-Scan, Verification Drive, and Documentation
For ADAS-related repairs on a Mitsubishi Colt, the absence of a warning light is a good sign, but it is not a complete acceptance test. Start with a post-repair scan across all relevant modules to confirm ADAS-related DTCs are cleared and that no new network, camera, or radar faults are present. If calibration or initialization was performed, keep the completion report showing which systems were calibrated and that each routine finished successfully. Next, validate operation the way the OEM intends. When procedures call for it, perform a verification drive to confirm lane keep assist remains available without frequent dropouts, adaptive cruise control engages and holds, and forward collision warning operates normally. If “system limited” messages return during the drive, treat them as evidence of an unresolved prerequisite or root-cause issue rather than assuming calibration failed. Also verify real-world conditions that impact performance: the windshield camera area is clean and unobstructed, wipers clear without streaking, and there is no haze, distortion, or glare affecting the camera’s view. Finally, organize documentation—pre-scan, post-scan, calibration printouts, and road-test notes—for insurance, resale value, and dispute prevention. Bang AutoGlass supports mobile next-day service and backs workmanship with a lifetime warranty.
Enjoy More Relevant Blogs
How Much Does ADAS Calibration Cost for Mitsubishi Colt? What Drives Pricing and What Insurance Typically Covers
How much does ADAS calibration cost for a Mitsubishi Colt? Learn pricing drivers, camera vs radar needs, labor time, and what insurance typically covers.
Pre- and Post-Calibration Scans for Mitsubishi Colt: Proving Systems Are Set Correctly
Pre- and post-calibration scans for Mitsubishi Colt: see why scans matter, what they verify, and how reports prove ADAS systems are set correctly after service.
Do You Need ADAS Calibration for Mitsubishi Colt After a Wheel Alignment, Suspension Work, or a Minor Collision?
Do you need ADAS calibration for a Mitsubishi Colt after alignment, suspension work, or a minor collision? Signs, timelines, safety risks, and costs today.
Camera Calibration for Mitsubishi Colt: Lane Assist and Forward Collision Accuracy Explained
Need camera calibration for your Mitsubishi Colt? See how calibration affects lane assist and forward collision accuracy after windshield service or repairs.
Mobile ADAS Calibration for Mitsubishi Colt: What to Expect On-Site and Why Setup Matters
Mobile ADAS calibration for Mitsubishi Colt: what to expect on-site, space and lighting needs, and why setup and verification matter after repairs today.
ADAS Calibration Checklist for Mitsubishi Colt: Documentation, Verification, and Final Safety Checks
ADAS calibration checklist for Mitsubishi Colt: documentation to request, scans to verify, and safety checks that confirm cameras and sensors are set right.
How to Schedule ADAS Calibration for Mitsubishi Colt After Windshield Replacement
Schedule ADAS calibration for Mitsubishi Colt after windshield replacement. Learn timing, required info, and what to expect so safety systems stay accurate.
OEM Calibration Requirements for Mitsubishi Colt: How to Confirm What Must Be Calibrated
OEM calibration requirements for Mitsubishi Colt: how to confirm what must be calibrated after repairs, what triggers recalibration, and what proof to ask for.
Static vs Dynamic ADAS Calibration for Mitsubishi Colt: What the Difference Means
Static vs dynamic ADAS calibration for Mitsubishi Colt: key differences, when each is required, how long it takes, and what affects accuracy for safety.
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm