Services
Service Areas
Shattered Back Window on Mitsubishi Montero Sport: A Step-by-Step Rear Glass Replacement Plan
Immediate Steps After Rear Glass Breakage on Mitsubishi Montero Sport: Safety, Visibility, and Securing the Vehicle
If the rear window on your Mitsubishi Montero Sport shatters, treat it as a safety and security issue until a professional rear window replacement is completed. If it breaks while driving, slow down, turn on hazard lights, and pull into a safe, well-lit area. Tempered back glass fractures into small cubes, but they can still cut skin and irritate eyes--avoid touching your face and keep children and pets away. With gloves and eye protection, remove only loose pieces that block visibility or could drop into the cabin. Next, protect the interior from weather and theft. Remove valuables and cover the opening with plastic sheeting or a heavy-duty bag, securing it with painter's tape or other low-tack tape. Do not slam doors or the hatch; pressure changes can dislodge remaining glass. Take photos for an insurance claim, since rear glass damage is commonly handled under comprehensive coverage. Bang AutoGlass makes Mitsubishi Montero Sport back glass replacement straightforward with fully mobile service, often as soon as next day. Most installs take about 30-45 minutes on site, then the urethane requires at least 1 hour of cure time before safe drive-away. Every job is backed by our lifetime workmanship warranty.
Cleanup Plan: Removing Shards, Vacuuming the Cabin, and Protecting Trim and Upholstery
A broken rear window means your Mitsubishi Montero Sport likely has glass in the rear deck, seat seams, and trunk/cargo area. Clean it in stages so you do not drive shards deeper into upholstery. Put on safety glasses, thick gloves, and sturdy shoes, and keep unprotected passengers out of the work area. If available, lay plastic sheeting over seats and the cargo floor before you start lifting pieces. Start with big fragments. Pick larger chunks from the window frame and rear deck and place them into a rigid box or thick contractor bag. Then vacuum slowly with a shop-vac or strong vacuum using a crevice tool. Follow a top-down route: headliner edge, trim gaps, rear deck, seat seams, floor mats, carpet, and the trunk well, including the spare-tire compartment. After the first vacuum, use painter's tape, packing tape wrapped sticky-side out, or a lint roller to lift fine "glass sand" from fabric and corners; repeat until the tape comes back clean. Finish by wiping plastics with a slightly damp microfiber towel rather than scrubbing. If you have mobile rear glass replacement scheduled with Bang AutoGlass, clear loose debris around the opening so the bond area stays clean.
Confirm the Correct Rear Glass for Mitsubishi Montero Sport: Defroster Grid, Antenna Lines, Tint, and DOT Markings
Ordering the rear glass for a Mitsubishi Montero Sport starts with matching the vehicle's options. Begin with the rear defroster: most Mitsubishi Montero Sport back windows use a printed heating grid, and the replacement must match the layout and have the connector tabs so it plugs into the factory harness. Also confirm antenna features. Many vehicles integrate AM/FM, GPS, or cellular traces into the rear window; if your reception depended on the original glass, you need an antenna-equipped replacement. Next, match tint and privacy shading. Rear glass may be clear, lightly tinted, or privacy glass. Matching shade matters for appearance, heat rejection, and (by state) compliance. If your Mitsubishi Montero Sport had aftermarket tint film, confirm whether film was applied over clear glass or whether the vehicle used privacy glass so you do not end up too light or too dark after rear windshield replacement. Finally, verify markings and fit. Automotive glass carries DOT identification and AS markings (AS2/AS3 are common on rear and side glass and can indicate tinted variations). VIN validation and the part number help ensure proper curvature, tempered-glass performance, and an insurance-friendly repair. Bang AutoGlass verifies these details before dispatching our mobile team, and every install is backed by our lifetime workmanship warranty.
Removal and Prep Steps: Interior Protection, Pinchweld Inspection, and Bond Surface Readiness
A quality rear glass replacement starts with careful removal and prep for your Mitsubishi Montero Sport. Bang AutoGlass covers the seats, rear deck, and cargo area, then removes trim, clips, and moldings needed to access the opening without scuffing interior panels. We clear tempered-glass fragments, manage rear defroster/antenna connectors, and cut the existing urethane with controlled tools so the vehicle aperture stays intact. Next we inspect the pinchweld-the metal bonding flange the urethane bonds to. Best practice is to remove most of the old urethane while leaving a thin, uniform base layer (about 1-2 mm) so new urethane bonds to cured urethane instead of bare metal. If we find scratches through paint, corrosion, or prior bodywork issues, we correct and prime/seal exposed metal because rust under the bond line is a common cause of leaks and adhesion loss. Finally, we dry-fit the replacement back glass for your Mitsubishi Montero Sport, confirm spacers and molding condition, clean the frit and aperture, and apply the proper primers/activators with correct flash times. With surfaces ready, we set the glass with even pressure for a consistent perimeter seal-mobile, next-day rear window replacement backed by our lifetime workmanship warranty.
Urethane Bonding and Minimum Drive-Away Time for Mitsubishi Montero Sport: What Controls Safe Release
For a Mitsubishi Montero Sport rear window replacement to be truly complete, the urethane bond must cure enough to hold the back glass under vibration, wind load, and weather. Auto glass urethane is typically a moisture-curing polyurethane adhesive, and manufacturers publish a Safe Drive-Away Time (SDAT) based on minimum bond strength. SDAT depends on the adhesive system, correct prep, and site conditions-especially temperature and relative humidity-plus respecting open-time limits so the glass is set before the bead skins over. Bond quality also relies on fundamentals: correct bead size and shape, clean primed surfaces, proper primer/activator flash times, and uniform set-down pressure so the bead compresses evenly around the perimeter. Contamination (dust, oils, silicone dressings) and unprotected bare metal are frequent causes of leaks or adhesion failure, so we keep the bond line clean and protected. At Bang AutoGlass, most Mitsubishi Montero Sport back glass replacements take about 30-45 minutes on site, followed by a minimum of 1 hour before we recommend safe drive-away. During that time, drive gently, avoid slamming doors, and skip automated car washes. If conditions are extreme, we'll advise more cure time. We also help with insurance claims under comprehensive coverage, all backed by our lifetime workmanship warranty.
Post-Install Verification: Defroster/Antenna Testing, Leak & Wind Noise Checks, and Documentation
After your Mitsubishi Montero Sport rear window replacement is installed, verification confirms the glass is correct, sealed, and functional. First, check electrical features: rear defroster connectors should be firmly seated on the tabs, and any in-glass antenna leads should be reconnected and strain-relieved so hatch or trunk movement won't tug the wiring. A quick function check helps you avoid discovering a loose connection or weak reception later. Next, validate sealing and wind noise. The molding and reveal line should be even, with consistent spacing around the perimeter. We perform a controlled perimeter water test to confirm there are no leaks, and when practical a short road test to replicate highway airflow; a whistle usually points to a small gap or mis-seated molding. As a simple owner check after rain, look for damp headliner edges or moisture in the cargo area. Finally, keep documentation: you should receive an invoice, warranty record, and notes on the rear glass installed for your Mitsubishi Montero Sport (tint, defroster grid, antenna integration, and DOT/AS markings). Bang AutoGlass backs workmanship with a lifetime workmanship warranty. Observe at least a 1-hour safe drive-away time and avoid automated car washes for the first day to protect the fresh urethane seal.
Services
Service Areas
Shattered Back Window on Mitsubishi Montero Sport: A Step-by-Step Rear Glass Replacement Plan
Immediate Steps After Rear Glass Breakage on Mitsubishi Montero Sport: Safety, Visibility, and Securing the Vehicle
If the rear window on your Mitsubishi Montero Sport shatters, treat it as a safety and security issue until a professional rear window replacement is completed. If it breaks while driving, slow down, turn on hazard lights, and pull into a safe, well-lit area. Tempered back glass fractures into small cubes, but they can still cut skin and irritate eyes--avoid touching your face and keep children and pets away. With gloves and eye protection, remove only loose pieces that block visibility or could drop into the cabin. Next, protect the interior from weather and theft. Remove valuables and cover the opening with plastic sheeting or a heavy-duty bag, securing it with painter's tape or other low-tack tape. Do not slam doors or the hatch; pressure changes can dislodge remaining glass. Take photos for an insurance claim, since rear glass damage is commonly handled under comprehensive coverage. Bang AutoGlass makes Mitsubishi Montero Sport back glass replacement straightforward with fully mobile service, often as soon as next day. Most installs take about 30-45 minutes on site, then the urethane requires at least 1 hour of cure time before safe drive-away. Every job is backed by our lifetime workmanship warranty.
Cleanup Plan: Removing Shards, Vacuuming the Cabin, and Protecting Trim and Upholstery
A broken rear window means your Mitsubishi Montero Sport likely has glass in the rear deck, seat seams, and trunk/cargo area. Clean it in stages so you do not drive shards deeper into upholstery. Put on safety glasses, thick gloves, and sturdy shoes, and keep unprotected passengers out of the work area. If available, lay plastic sheeting over seats and the cargo floor before you start lifting pieces. Start with big fragments. Pick larger chunks from the window frame and rear deck and place them into a rigid box or thick contractor bag. Then vacuum slowly with a shop-vac or strong vacuum using a crevice tool. Follow a top-down route: headliner edge, trim gaps, rear deck, seat seams, floor mats, carpet, and the trunk well, including the spare-tire compartment. After the first vacuum, use painter's tape, packing tape wrapped sticky-side out, or a lint roller to lift fine "glass sand" from fabric and corners; repeat until the tape comes back clean. Finish by wiping plastics with a slightly damp microfiber towel rather than scrubbing. If you have mobile rear glass replacement scheduled with Bang AutoGlass, clear loose debris around the opening so the bond area stays clean.
Confirm the Correct Rear Glass for Mitsubishi Montero Sport: Defroster Grid, Antenna Lines, Tint, and DOT Markings
Ordering the rear glass for a Mitsubishi Montero Sport starts with matching the vehicle's options. Begin with the rear defroster: most Mitsubishi Montero Sport back windows use a printed heating grid, and the replacement must match the layout and have the connector tabs so it plugs into the factory harness. Also confirm antenna features. Many vehicles integrate AM/FM, GPS, or cellular traces into the rear window; if your reception depended on the original glass, you need an antenna-equipped replacement. Next, match tint and privacy shading. Rear glass may be clear, lightly tinted, or privacy glass. Matching shade matters for appearance, heat rejection, and (by state) compliance. If your Mitsubishi Montero Sport had aftermarket tint film, confirm whether film was applied over clear glass or whether the vehicle used privacy glass so you do not end up too light or too dark after rear windshield replacement. Finally, verify markings and fit. Automotive glass carries DOT identification and AS markings (AS2/AS3 are common on rear and side glass and can indicate tinted variations). VIN validation and the part number help ensure proper curvature, tempered-glass performance, and an insurance-friendly repair. Bang AutoGlass verifies these details before dispatching our mobile team, and every install is backed by our lifetime workmanship warranty.
Removal and Prep Steps: Interior Protection, Pinchweld Inspection, and Bond Surface Readiness
A quality rear glass replacement starts with careful removal and prep for your Mitsubishi Montero Sport. Bang AutoGlass covers the seats, rear deck, and cargo area, then removes trim, clips, and moldings needed to access the opening without scuffing interior panels. We clear tempered-glass fragments, manage rear defroster/antenna connectors, and cut the existing urethane with controlled tools so the vehicle aperture stays intact. Next we inspect the pinchweld-the metal bonding flange the urethane bonds to. Best practice is to remove most of the old urethane while leaving a thin, uniform base layer (about 1-2 mm) so new urethane bonds to cured urethane instead of bare metal. If we find scratches through paint, corrosion, or prior bodywork issues, we correct and prime/seal exposed metal because rust under the bond line is a common cause of leaks and adhesion loss. Finally, we dry-fit the replacement back glass for your Mitsubishi Montero Sport, confirm spacers and molding condition, clean the frit and aperture, and apply the proper primers/activators with correct flash times. With surfaces ready, we set the glass with even pressure for a consistent perimeter seal-mobile, next-day rear window replacement backed by our lifetime workmanship warranty.
Urethane Bonding and Minimum Drive-Away Time for Mitsubishi Montero Sport: What Controls Safe Release
For a Mitsubishi Montero Sport rear window replacement to be truly complete, the urethane bond must cure enough to hold the back glass under vibration, wind load, and weather. Auto glass urethane is typically a moisture-curing polyurethane adhesive, and manufacturers publish a Safe Drive-Away Time (SDAT) based on minimum bond strength. SDAT depends on the adhesive system, correct prep, and site conditions-especially temperature and relative humidity-plus respecting open-time limits so the glass is set before the bead skins over. Bond quality also relies on fundamentals: correct bead size and shape, clean primed surfaces, proper primer/activator flash times, and uniform set-down pressure so the bead compresses evenly around the perimeter. Contamination (dust, oils, silicone dressings) and unprotected bare metal are frequent causes of leaks or adhesion failure, so we keep the bond line clean and protected. At Bang AutoGlass, most Mitsubishi Montero Sport back glass replacements take about 30-45 minutes on site, followed by a minimum of 1 hour before we recommend safe drive-away. During that time, drive gently, avoid slamming doors, and skip automated car washes. If conditions are extreme, we'll advise more cure time. We also help with insurance claims under comprehensive coverage, all backed by our lifetime workmanship warranty.
Post-Install Verification: Defroster/Antenna Testing, Leak & Wind Noise Checks, and Documentation
After your Mitsubishi Montero Sport rear window replacement is installed, verification confirms the glass is correct, sealed, and functional. First, check electrical features: rear defroster connectors should be firmly seated on the tabs, and any in-glass antenna leads should be reconnected and strain-relieved so hatch or trunk movement won't tug the wiring. A quick function check helps you avoid discovering a loose connection or weak reception later. Next, validate sealing and wind noise. The molding and reveal line should be even, with consistent spacing around the perimeter. We perform a controlled perimeter water test to confirm there are no leaks, and when practical a short road test to replicate highway airflow; a whistle usually points to a small gap or mis-seated molding. As a simple owner check after rain, look for damp headliner edges or moisture in the cargo area. Finally, keep documentation: you should receive an invoice, warranty record, and notes on the rear glass installed for your Mitsubishi Montero Sport (tint, defroster grid, antenna integration, and DOT/AS markings). Bang AutoGlass backs workmanship with a lifetime workmanship warranty. Observe at least a 1-hour safe drive-away time and avoid automated car washes for the first day to protect the fresh urethane seal.
Services
Service Areas
Shattered Back Window on Mitsubishi Montero Sport: A Step-by-Step Rear Glass Replacement Plan
Immediate Steps After Rear Glass Breakage on Mitsubishi Montero Sport: Safety, Visibility, and Securing the Vehicle
If the rear window on your Mitsubishi Montero Sport shatters, treat it as a safety and security issue until a professional rear window replacement is completed. If it breaks while driving, slow down, turn on hazard lights, and pull into a safe, well-lit area. Tempered back glass fractures into small cubes, but they can still cut skin and irritate eyes--avoid touching your face and keep children and pets away. With gloves and eye protection, remove only loose pieces that block visibility or could drop into the cabin. Next, protect the interior from weather and theft. Remove valuables and cover the opening with plastic sheeting or a heavy-duty bag, securing it with painter's tape or other low-tack tape. Do not slam doors or the hatch; pressure changes can dislodge remaining glass. Take photos for an insurance claim, since rear glass damage is commonly handled under comprehensive coverage. Bang AutoGlass makes Mitsubishi Montero Sport back glass replacement straightforward with fully mobile service, often as soon as next day. Most installs take about 30-45 minutes on site, then the urethane requires at least 1 hour of cure time before safe drive-away. Every job is backed by our lifetime workmanship warranty.
Cleanup Plan: Removing Shards, Vacuuming the Cabin, and Protecting Trim and Upholstery
A broken rear window means your Mitsubishi Montero Sport likely has glass in the rear deck, seat seams, and trunk/cargo area. Clean it in stages so you do not drive shards deeper into upholstery. Put on safety glasses, thick gloves, and sturdy shoes, and keep unprotected passengers out of the work area. If available, lay plastic sheeting over seats and the cargo floor before you start lifting pieces. Start with big fragments. Pick larger chunks from the window frame and rear deck and place them into a rigid box or thick contractor bag. Then vacuum slowly with a shop-vac or strong vacuum using a crevice tool. Follow a top-down route: headliner edge, trim gaps, rear deck, seat seams, floor mats, carpet, and the trunk well, including the spare-tire compartment. After the first vacuum, use painter's tape, packing tape wrapped sticky-side out, or a lint roller to lift fine "glass sand" from fabric and corners; repeat until the tape comes back clean. Finish by wiping plastics with a slightly damp microfiber towel rather than scrubbing. If you have mobile rear glass replacement scheduled with Bang AutoGlass, clear loose debris around the opening so the bond area stays clean.
Confirm the Correct Rear Glass for Mitsubishi Montero Sport: Defroster Grid, Antenna Lines, Tint, and DOT Markings
Ordering the rear glass for a Mitsubishi Montero Sport starts with matching the vehicle's options. Begin with the rear defroster: most Mitsubishi Montero Sport back windows use a printed heating grid, and the replacement must match the layout and have the connector tabs so it plugs into the factory harness. Also confirm antenna features. Many vehicles integrate AM/FM, GPS, or cellular traces into the rear window; if your reception depended on the original glass, you need an antenna-equipped replacement. Next, match tint and privacy shading. Rear glass may be clear, lightly tinted, or privacy glass. Matching shade matters for appearance, heat rejection, and (by state) compliance. If your Mitsubishi Montero Sport had aftermarket tint film, confirm whether film was applied over clear glass or whether the vehicle used privacy glass so you do not end up too light or too dark after rear windshield replacement. Finally, verify markings and fit. Automotive glass carries DOT identification and AS markings (AS2/AS3 are common on rear and side glass and can indicate tinted variations). VIN validation and the part number help ensure proper curvature, tempered-glass performance, and an insurance-friendly repair. Bang AutoGlass verifies these details before dispatching our mobile team, and every install is backed by our lifetime workmanship warranty.
Removal and Prep Steps: Interior Protection, Pinchweld Inspection, and Bond Surface Readiness
A quality rear glass replacement starts with careful removal and prep for your Mitsubishi Montero Sport. Bang AutoGlass covers the seats, rear deck, and cargo area, then removes trim, clips, and moldings needed to access the opening without scuffing interior panels. We clear tempered-glass fragments, manage rear defroster/antenna connectors, and cut the existing urethane with controlled tools so the vehicle aperture stays intact. Next we inspect the pinchweld-the metal bonding flange the urethane bonds to. Best practice is to remove most of the old urethane while leaving a thin, uniform base layer (about 1-2 mm) so new urethane bonds to cured urethane instead of bare metal. If we find scratches through paint, corrosion, or prior bodywork issues, we correct and prime/seal exposed metal because rust under the bond line is a common cause of leaks and adhesion loss. Finally, we dry-fit the replacement back glass for your Mitsubishi Montero Sport, confirm spacers and molding condition, clean the frit and aperture, and apply the proper primers/activators with correct flash times. With surfaces ready, we set the glass with even pressure for a consistent perimeter seal-mobile, next-day rear window replacement backed by our lifetime workmanship warranty.
Urethane Bonding and Minimum Drive-Away Time for Mitsubishi Montero Sport: What Controls Safe Release
For a Mitsubishi Montero Sport rear window replacement to be truly complete, the urethane bond must cure enough to hold the back glass under vibration, wind load, and weather. Auto glass urethane is typically a moisture-curing polyurethane adhesive, and manufacturers publish a Safe Drive-Away Time (SDAT) based on minimum bond strength. SDAT depends on the adhesive system, correct prep, and site conditions-especially temperature and relative humidity-plus respecting open-time limits so the glass is set before the bead skins over. Bond quality also relies on fundamentals: correct bead size and shape, clean primed surfaces, proper primer/activator flash times, and uniform set-down pressure so the bead compresses evenly around the perimeter. Contamination (dust, oils, silicone dressings) and unprotected bare metal are frequent causes of leaks or adhesion failure, so we keep the bond line clean and protected. At Bang AutoGlass, most Mitsubishi Montero Sport back glass replacements take about 30-45 minutes on site, followed by a minimum of 1 hour before we recommend safe drive-away. During that time, drive gently, avoid slamming doors, and skip automated car washes. If conditions are extreme, we'll advise more cure time. We also help with insurance claims under comprehensive coverage, all backed by our lifetime workmanship warranty.
Post-Install Verification: Defroster/Antenna Testing, Leak & Wind Noise Checks, and Documentation
After your Mitsubishi Montero Sport rear window replacement is installed, verification confirms the glass is correct, sealed, and functional. First, check electrical features: rear defroster connectors should be firmly seated on the tabs, and any in-glass antenna leads should be reconnected and strain-relieved so hatch or trunk movement won't tug the wiring. A quick function check helps you avoid discovering a loose connection or weak reception later. Next, validate sealing and wind noise. The molding and reveal line should be even, with consistent spacing around the perimeter. We perform a controlled perimeter water test to confirm there are no leaks, and when practical a short road test to replicate highway airflow; a whistle usually points to a small gap or mis-seated molding. As a simple owner check after rain, look for damp headliner edges or moisture in the cargo area. Finally, keep documentation: you should receive an invoice, warranty record, and notes on the rear glass installed for your Mitsubishi Montero Sport (tint, defroster grid, antenna integration, and DOT/AS markings). Bang AutoGlass backs workmanship with a lifetime workmanship warranty. Observe at least a 1-hour safe drive-away time and avoid automated car washes for the first day to protect the fresh urethane seal.
Enjoy More Relevant Blogs
How Long Does Rear Glass Replacement Take on Mitsubishi Montero Sport? Install Time, Adhesive Cure Time, and When It’s Safe to Drive
How long is Mitsubishi Montero Sport rear glass replacement? Get install time, urethane cure guidelines, and drive-away timing after service. Plan your visit today.
Rear Glass Replacement for Mitsubishi Montero Sport: What to Expect During Install and Aftercare
Rear glass replacement for Mitsubishi Montero Sport: what happens during install, defroster and tint considerations, cure time, and aftercare to prevent leaks long-term.
How to Schedule Mobile Rear Glass Replacement for Mitsubishi Montero Sport
Schedule mobile rear glass replacement for your Mitsubishi Montero Sport in minutes. Learn what info to provide, how long it takes, and prep tips for service day.
Tempered Safety Rear Glass Replacement for Mitsubishi Montero Sport: Understanding DOT Markings and FMVSS 205
Need Mitsubishi Montero Sport rear glass replacement? Learn tempered safety glass basics, DOT markings, and FMVSS 205, plus install and cure tips. Get a quote today.
Back Glass Replacement on Mitsubishi Montero Sport: Defroster Tabs, Antenna Lines, and Connector Reattachment Basics
Back glass replacement on Mitsubishi Montero Sport: defroster tabs, antenna lines, and connectors explained, plus install tips to avoid damage and rework safely.
Post-Install Checks for Mitsubishi Montero Sport: Rear Glass Replacement Wind Noise, Leaks, and Rattle Tests
Post-install rear glass checks for Mitsubishi Montero Sport: test for wind noise, leaks, and rattles, plus when to return for warranty service—check today before trips.
OEM-Quality Rear Glass Replacement for Mitsubishi Montero Sport: Defroster Grid and Tint-Match Checklist
OEM-quality rear glass replacement for Mitsubishi Montero Sport: defroster grid and tint-match checklist, plus install tips to avoid callbacks—schedule service.
How Much Does Rear Glass Replacement Cost for Mitsubishi Montero Sport? Pricing Factors, OEM vs Aftermarket, and Insurance Deductibles
Estimate Mitsubishi Montero Sport rear glass replacement cost. Compare OEM vs aftermarket, labor factors, insurance deductibles, and ways to save. Request a quote.
Rear Defroster Not Working on Mitsubishi Montero Sport? When Rear Glass Replacement Makes More Sense Than Repair
Rear defroster not working on your Mitsubishi Montero Sport? Learn common causes, when repair fails, and when rear glass replacement is the smarter fix for winter.
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm