Services
Service Areas
OEM-Quality Rear Glass Replacement for Mitsubishi Xpander Cross: Defroster Grid and Tint-Match Checklist
Verify the Correct Mitsubishi Xpander Cross Rear Glass: Privacy Shade, Defroster Grid, Antenna Lines, and DOT Markings
Choosing OEM-quality rear glass for your Mitsubishi Xpander Cross is about matching features as much as matching the opening. We confirm whether your vehicle uses privacy shade (tinted-in-glass), a rear defroster grid, and any embedded antenna lines for radio, GPS, or keyless entry. We also check the hatch or liftgate for brackets, mounting pads, and cutouts that must be present for a factory-style fit. To keep the install looking OEM, we match the frit band (black ceramic border) so the urethane bonding area and UV shielding are correct. Next we verify the glass etching: U.S. automotive glazing typically references FMVSS 205 and includes a DOT number that identifies the manufacturer or plant. Most rear panels are tempered and often marked AS-2 for rear/side use. We then confirm orientation and options such as third brake lamp visibility, wiper provisions (when equipped), and any openings for cameras or sensors. Bang AutoGlass performs this verification before we arrive in {city}, {state} so your Mitsubishi Xpander Cross rear window replacement is done right. Most jobs take 30-45 minutes, plus at least one hour of safe cure time. Every install is backed by a lifetime workmanship warranty, and we work with all insurance companies when comprehensive coverage applies.
Tint-Match Checklist for Mitsubishi Xpander Cross: Privacy Glass vs Film, VLT Expectations, and Color Tone
When you request a "tint match" for a Mitsubishi Xpander Cross rear glass replacement, we first confirm whether you are matching factory privacy glass or added tint film. Privacy glass is dyed in the glass; film is applied to the inside surface later. If your Mitsubishi Xpander Cross originally had privacy glass, the most OEM result is installing OEM-quality privacy rear glass with the correct DOT/AS markings and built-in shade. Then we evaluate VLT, net VLT, and tone. VLT (Visible Light Transmission) measures how much light passes through a single layer. Factory privacy glass on many SUVs and trucks is often around 15-26% VLT, while clear glass may be closer to 70-85% VLT, so a clear replacement can look obviously different. If the prior rear window also had film, the final shade is net VLT (glass plus film), so plan to re-tint after replacement for a true match. Tone is the next giveaway: some privacy glass leans charcoal/gray, others show a green or bronze cast, and it should track your other rear panels. Because tint rules vary by {state}, we focus on duplicating what you had. Bang AutoGlass is mobile in {city}, {state}, often available next day, and every rear window replacement is backed by a lifetime workmanship warranty.
Rear Defroster Grid Basics: Lines, Power Tabs, and What Common Failures Look Like
On a Mitsubishi Xpander Cross, the rear defroster is a resistive heating circuit printed on the inside of the back glass. The horizontal grid lines are conductive traces, and vertical bus bars distribute power. When you press the rear defrost button, the system typically applies around 12-14 volts through power and ground terminals bonded to the glass, warming the surface to clear condensation and frost. Because the electrical connection is made at the tabs, a problem there can mimic a larger failure. A loose connector, corrosion at the terminal, or a detached tab can shut down the grid even if the lines appear unbroken. If only part of the window clears, that usually points to damaged grid lines rather than a fuse or relay. Breaks are often caused by scraping ice, removing stickers, or using cleaners and abrasive pads. If the defroster light turns on but nothing clears anywhere, upstream causes include a blown fuse, bad relay, switch issue, control module fault, or poor ground. During OEM-quality rear glass replacement on your Mitsubishi Xpander Cross, we confirm the grid pattern, tab placement, and connector fit so the defroster reconnects reliably. Bang AutoGlass is mobile in {city}, {state}, and every rear window replacement is backed by our lifetime workmanship warranty.
Install Prep That Protects Fit: Interior Protection, Pinchweld Checks, and Bond Surface Readiness
Rear glass replacement quality on a Mitsubishi Xpander Cross is determined before the new panel is ever set. Bang AutoGlass starts by protecting the interior—seats, headliner, trim, and cargo area—then removing necessary moldings and liftgate panels and vacuuming thoroughly to keep debris out of latches and interior panels. Next we inspect the pinchweld/bonding flange for rust, paint damage, and signs of prior substandard repairs that can compromise urethane adhesion. Standard stationary-glass practice is to trim existing urethane to a thin, uniform layer (about 1–2 mm) so fresh urethane bonds reliably to a stable base while minimizing exposed metal. If bare metal or corrosion is present, we address it with proper surface prep and the correct primer for the adhesive system. We then dry-fit OEM-quality rear glass to confirm alignment, molding fit, and consistent gaps, prep the glass frit and vehicle bonding surface with approved cleaner/primer, and lay a consistent urethane bead before setting the glass square to avoid leaks and whistles. We're mobile in {city}, {state}, often next day. Most installs take 30–45 minutes plus at least one hour of safe cure time. Every job includes a lifetime workmanship warranty, and we work with all insurance companies when comprehensive coverage applies.
Defroster Reconnect and Testing: Tabs, Harness Connection, and Function Verification on Mitsubishi Xpander Cross
Once the new rear glass is set on your Mitsubishi Xpander Cross, the next priority is restoring the rear defroster circuit correctly. The grid is printed on the inside of the glass and interfaces through two bonded tabs (power/ground) and a harness connector. We confirm the grid layout and that tab locations match your Mitsubishi Xpander Cross so the connector reaches without tension. Reconnection is done with a straight seating motion; twisting or prying can stress tabs and create future intermittent failures. We also verify the connector is clean and fully seated—a loose fit can cause uneven heating or a complete no-heat condition. Before we leave {city}, {state}, we perform a functional verification: with the vehicle on and the defroster commanded on, you should see voltage at the terminals and the grid should begin warming within about a minute. If the indicator is lit but nothing clears, common causes include a blown fuse, relay fault, switch/control issue, or poor ground. If only bands clear, that pattern usually points to broken grid lines from scraping or abrasive cleaning. Clean gently to protect the traces. Bang AutoGlass is mobile, often next day, backed by a lifetime workmanship warranty, and we accept all insurance companies when comprehensive coverage applies.
Aftercare and Final QC: Safe Drive-Away Timing, Leak/Wind Noise Checks, and Defroster Use
Aftercare and final QC separate a routine rear glass replacement from an OEM-quality result on your Mitsubishi Xpander Cross. Before we pack up, we confirm the glass is seated evenly and that moldings, garnish trim, and retainers are flush. We inspect the urethane bond line for continuity around the opening, because small voids can later become leaks, a damp headliner, or a whistle at highway speed. Where conditions allow, we do a quick leak-risk/wind-noise check and confirm the rear defroster connector is secure and responding normally. Most rear glass replacements take 30–45 minutes, and we recommend at least one hour of safe drive-away time so the adhesive can set. Because cure continues and temperature and humidity in {city}, {state} can influence results, treat the first day as low-stress. Avoid automatic or high-pressure car washes for at least 48 hours and minimize door slams and rough-road impacts. If retention tape is used, leave it in place as directed. Quick defroster checks are fine, but avoid extended cycles for about 24 hours. If you notice water intrusion, wind noise, or shifting trim, contact Bang AutoGlass—covered by our lifetime workmanship warranty, and we work with all insurance companies when comprehensive coverage applies.
Services
Service Areas
OEM-Quality Rear Glass Replacement for Mitsubishi Xpander Cross: Defroster Grid and Tint-Match Checklist
Verify the Correct Mitsubishi Xpander Cross Rear Glass: Privacy Shade, Defroster Grid, Antenna Lines, and DOT Markings
Choosing OEM-quality rear glass for your Mitsubishi Xpander Cross is about matching features as much as matching the opening. We confirm whether your vehicle uses privacy shade (tinted-in-glass), a rear defroster grid, and any embedded antenna lines for radio, GPS, or keyless entry. We also check the hatch or liftgate for brackets, mounting pads, and cutouts that must be present for a factory-style fit. To keep the install looking OEM, we match the frit band (black ceramic border) so the urethane bonding area and UV shielding are correct. Next we verify the glass etching: U.S. automotive glazing typically references FMVSS 205 and includes a DOT number that identifies the manufacturer or plant. Most rear panels are tempered and often marked AS-2 for rear/side use. We then confirm orientation and options such as third brake lamp visibility, wiper provisions (when equipped), and any openings for cameras or sensors. Bang AutoGlass performs this verification before we arrive in {city}, {state} so your Mitsubishi Xpander Cross rear window replacement is done right. Most jobs take 30-45 minutes, plus at least one hour of safe cure time. Every install is backed by a lifetime workmanship warranty, and we work with all insurance companies when comprehensive coverage applies.
Tint-Match Checklist for Mitsubishi Xpander Cross: Privacy Glass vs Film, VLT Expectations, and Color Tone
When you request a "tint match" for a Mitsubishi Xpander Cross rear glass replacement, we first confirm whether you are matching factory privacy glass or added tint film. Privacy glass is dyed in the glass; film is applied to the inside surface later. If your Mitsubishi Xpander Cross originally had privacy glass, the most OEM result is installing OEM-quality privacy rear glass with the correct DOT/AS markings and built-in shade. Then we evaluate VLT, net VLT, and tone. VLT (Visible Light Transmission) measures how much light passes through a single layer. Factory privacy glass on many SUVs and trucks is often around 15-26% VLT, while clear glass may be closer to 70-85% VLT, so a clear replacement can look obviously different. If the prior rear window also had film, the final shade is net VLT (glass plus film), so plan to re-tint after replacement for a true match. Tone is the next giveaway: some privacy glass leans charcoal/gray, others show a green or bronze cast, and it should track your other rear panels. Because tint rules vary by {state}, we focus on duplicating what you had. Bang AutoGlass is mobile in {city}, {state}, often available next day, and every rear window replacement is backed by a lifetime workmanship warranty.
Rear Defroster Grid Basics: Lines, Power Tabs, and What Common Failures Look Like
On a Mitsubishi Xpander Cross, the rear defroster is a resistive heating circuit printed on the inside of the back glass. The horizontal grid lines are conductive traces, and vertical bus bars distribute power. When you press the rear defrost button, the system typically applies around 12-14 volts through power and ground terminals bonded to the glass, warming the surface to clear condensation and frost. Because the electrical connection is made at the tabs, a problem there can mimic a larger failure. A loose connector, corrosion at the terminal, or a detached tab can shut down the grid even if the lines appear unbroken. If only part of the window clears, that usually points to damaged grid lines rather than a fuse or relay. Breaks are often caused by scraping ice, removing stickers, or using cleaners and abrasive pads. If the defroster light turns on but nothing clears anywhere, upstream causes include a blown fuse, bad relay, switch issue, control module fault, or poor ground. During OEM-quality rear glass replacement on your Mitsubishi Xpander Cross, we confirm the grid pattern, tab placement, and connector fit so the defroster reconnects reliably. Bang AutoGlass is mobile in {city}, {state}, and every rear window replacement is backed by our lifetime workmanship warranty.
Install Prep That Protects Fit: Interior Protection, Pinchweld Checks, and Bond Surface Readiness
Rear glass replacement quality on a Mitsubishi Xpander Cross is determined before the new panel is ever set. Bang AutoGlass starts by protecting the interior—seats, headliner, trim, and cargo area—then removing necessary moldings and liftgate panels and vacuuming thoroughly to keep debris out of latches and interior panels. Next we inspect the pinchweld/bonding flange for rust, paint damage, and signs of prior substandard repairs that can compromise urethane adhesion. Standard stationary-glass practice is to trim existing urethane to a thin, uniform layer (about 1–2 mm) so fresh urethane bonds reliably to a stable base while minimizing exposed metal. If bare metal or corrosion is present, we address it with proper surface prep and the correct primer for the adhesive system. We then dry-fit OEM-quality rear glass to confirm alignment, molding fit, and consistent gaps, prep the glass frit and vehicle bonding surface with approved cleaner/primer, and lay a consistent urethane bead before setting the glass square to avoid leaks and whistles. We're mobile in {city}, {state}, often next day. Most installs take 30–45 minutes plus at least one hour of safe cure time. Every job includes a lifetime workmanship warranty, and we work with all insurance companies when comprehensive coverage applies.
Defroster Reconnect and Testing: Tabs, Harness Connection, and Function Verification on Mitsubishi Xpander Cross
Once the new rear glass is set on your Mitsubishi Xpander Cross, the next priority is restoring the rear defroster circuit correctly. The grid is printed on the inside of the glass and interfaces through two bonded tabs (power/ground) and a harness connector. We confirm the grid layout and that tab locations match your Mitsubishi Xpander Cross so the connector reaches without tension. Reconnection is done with a straight seating motion; twisting or prying can stress tabs and create future intermittent failures. We also verify the connector is clean and fully seated—a loose fit can cause uneven heating or a complete no-heat condition. Before we leave {city}, {state}, we perform a functional verification: with the vehicle on and the defroster commanded on, you should see voltage at the terminals and the grid should begin warming within about a minute. If the indicator is lit but nothing clears, common causes include a blown fuse, relay fault, switch/control issue, or poor ground. If only bands clear, that pattern usually points to broken grid lines from scraping or abrasive cleaning. Clean gently to protect the traces. Bang AutoGlass is mobile, often next day, backed by a lifetime workmanship warranty, and we accept all insurance companies when comprehensive coverage applies.
Aftercare and Final QC: Safe Drive-Away Timing, Leak/Wind Noise Checks, and Defroster Use
Aftercare and final QC separate a routine rear glass replacement from an OEM-quality result on your Mitsubishi Xpander Cross. Before we pack up, we confirm the glass is seated evenly and that moldings, garnish trim, and retainers are flush. We inspect the urethane bond line for continuity around the opening, because small voids can later become leaks, a damp headliner, or a whistle at highway speed. Where conditions allow, we do a quick leak-risk/wind-noise check and confirm the rear defroster connector is secure and responding normally. Most rear glass replacements take 30–45 minutes, and we recommend at least one hour of safe drive-away time so the adhesive can set. Because cure continues and temperature and humidity in {city}, {state} can influence results, treat the first day as low-stress. Avoid automatic or high-pressure car washes for at least 48 hours and minimize door slams and rough-road impacts. If retention tape is used, leave it in place as directed. Quick defroster checks are fine, but avoid extended cycles for about 24 hours. If you notice water intrusion, wind noise, or shifting trim, contact Bang AutoGlass—covered by our lifetime workmanship warranty, and we work with all insurance companies when comprehensive coverage applies.
Services
Service Areas
OEM-Quality Rear Glass Replacement for Mitsubishi Xpander Cross: Defroster Grid and Tint-Match Checklist
Verify the Correct Mitsubishi Xpander Cross Rear Glass: Privacy Shade, Defroster Grid, Antenna Lines, and DOT Markings
Choosing OEM-quality rear glass for your Mitsubishi Xpander Cross is about matching features as much as matching the opening. We confirm whether your vehicle uses privacy shade (tinted-in-glass), a rear defroster grid, and any embedded antenna lines for radio, GPS, or keyless entry. We also check the hatch or liftgate for brackets, mounting pads, and cutouts that must be present for a factory-style fit. To keep the install looking OEM, we match the frit band (black ceramic border) so the urethane bonding area and UV shielding are correct. Next we verify the glass etching: U.S. automotive glazing typically references FMVSS 205 and includes a DOT number that identifies the manufacturer or plant. Most rear panels are tempered and often marked AS-2 for rear/side use. We then confirm orientation and options such as third brake lamp visibility, wiper provisions (when equipped), and any openings for cameras or sensors. Bang AutoGlass performs this verification before we arrive in {city}, {state} so your Mitsubishi Xpander Cross rear window replacement is done right. Most jobs take 30-45 minutes, plus at least one hour of safe cure time. Every install is backed by a lifetime workmanship warranty, and we work with all insurance companies when comprehensive coverage applies.
Tint-Match Checklist for Mitsubishi Xpander Cross: Privacy Glass vs Film, VLT Expectations, and Color Tone
When you request a "tint match" for a Mitsubishi Xpander Cross rear glass replacement, we first confirm whether you are matching factory privacy glass or added tint film. Privacy glass is dyed in the glass; film is applied to the inside surface later. If your Mitsubishi Xpander Cross originally had privacy glass, the most OEM result is installing OEM-quality privacy rear glass with the correct DOT/AS markings and built-in shade. Then we evaluate VLT, net VLT, and tone. VLT (Visible Light Transmission) measures how much light passes through a single layer. Factory privacy glass on many SUVs and trucks is often around 15-26% VLT, while clear glass may be closer to 70-85% VLT, so a clear replacement can look obviously different. If the prior rear window also had film, the final shade is net VLT (glass plus film), so plan to re-tint after replacement for a true match. Tone is the next giveaway: some privacy glass leans charcoal/gray, others show a green or bronze cast, and it should track your other rear panels. Because tint rules vary by {state}, we focus on duplicating what you had. Bang AutoGlass is mobile in {city}, {state}, often available next day, and every rear window replacement is backed by a lifetime workmanship warranty.
Rear Defroster Grid Basics: Lines, Power Tabs, and What Common Failures Look Like
On a Mitsubishi Xpander Cross, the rear defroster is a resistive heating circuit printed on the inside of the back glass. The horizontal grid lines are conductive traces, and vertical bus bars distribute power. When you press the rear defrost button, the system typically applies around 12-14 volts through power and ground terminals bonded to the glass, warming the surface to clear condensation and frost. Because the electrical connection is made at the tabs, a problem there can mimic a larger failure. A loose connector, corrosion at the terminal, or a detached tab can shut down the grid even if the lines appear unbroken. If only part of the window clears, that usually points to damaged grid lines rather than a fuse or relay. Breaks are often caused by scraping ice, removing stickers, or using cleaners and abrasive pads. If the defroster light turns on but nothing clears anywhere, upstream causes include a blown fuse, bad relay, switch issue, control module fault, or poor ground. During OEM-quality rear glass replacement on your Mitsubishi Xpander Cross, we confirm the grid pattern, tab placement, and connector fit so the defroster reconnects reliably. Bang AutoGlass is mobile in {city}, {state}, and every rear window replacement is backed by our lifetime workmanship warranty.
Install Prep That Protects Fit: Interior Protection, Pinchweld Checks, and Bond Surface Readiness
Rear glass replacement quality on a Mitsubishi Xpander Cross is determined before the new panel is ever set. Bang AutoGlass starts by protecting the interior—seats, headliner, trim, and cargo area—then removing necessary moldings and liftgate panels and vacuuming thoroughly to keep debris out of latches and interior panels. Next we inspect the pinchweld/bonding flange for rust, paint damage, and signs of prior substandard repairs that can compromise urethane adhesion. Standard stationary-glass practice is to trim existing urethane to a thin, uniform layer (about 1–2 mm) so fresh urethane bonds reliably to a stable base while minimizing exposed metal. If bare metal or corrosion is present, we address it with proper surface prep and the correct primer for the adhesive system. We then dry-fit OEM-quality rear glass to confirm alignment, molding fit, and consistent gaps, prep the glass frit and vehicle bonding surface with approved cleaner/primer, and lay a consistent urethane bead before setting the glass square to avoid leaks and whistles. We're mobile in {city}, {state}, often next day. Most installs take 30–45 minutes plus at least one hour of safe cure time. Every job includes a lifetime workmanship warranty, and we work with all insurance companies when comprehensive coverage applies.
Defroster Reconnect and Testing: Tabs, Harness Connection, and Function Verification on Mitsubishi Xpander Cross
Once the new rear glass is set on your Mitsubishi Xpander Cross, the next priority is restoring the rear defroster circuit correctly. The grid is printed on the inside of the glass and interfaces through two bonded tabs (power/ground) and a harness connector. We confirm the grid layout and that tab locations match your Mitsubishi Xpander Cross so the connector reaches without tension. Reconnection is done with a straight seating motion; twisting or prying can stress tabs and create future intermittent failures. We also verify the connector is clean and fully seated—a loose fit can cause uneven heating or a complete no-heat condition. Before we leave {city}, {state}, we perform a functional verification: with the vehicle on and the defroster commanded on, you should see voltage at the terminals and the grid should begin warming within about a minute. If the indicator is lit but nothing clears, common causes include a blown fuse, relay fault, switch/control issue, or poor ground. If only bands clear, that pattern usually points to broken grid lines from scraping or abrasive cleaning. Clean gently to protect the traces. Bang AutoGlass is mobile, often next day, backed by a lifetime workmanship warranty, and we accept all insurance companies when comprehensive coverage applies.
Aftercare and Final QC: Safe Drive-Away Timing, Leak/Wind Noise Checks, and Defroster Use
Aftercare and final QC separate a routine rear glass replacement from an OEM-quality result on your Mitsubishi Xpander Cross. Before we pack up, we confirm the glass is seated evenly and that moldings, garnish trim, and retainers are flush. We inspect the urethane bond line for continuity around the opening, because small voids can later become leaks, a damp headliner, or a whistle at highway speed. Where conditions allow, we do a quick leak-risk/wind-noise check and confirm the rear defroster connector is secure and responding normally. Most rear glass replacements take 30–45 minutes, and we recommend at least one hour of safe drive-away time so the adhesive can set. Because cure continues and temperature and humidity in {city}, {state} can influence results, treat the first day as low-stress. Avoid automatic or high-pressure car washes for at least 48 hours and minimize door slams and rough-road impacts. If retention tape is used, leave it in place as directed. Quick defroster checks are fine, but avoid extended cycles for about 24 hours. If you notice water intrusion, wind noise, or shifting trim, contact Bang AutoGlass—covered by our lifetime workmanship warranty, and we work with all insurance companies when comprehensive coverage applies.
Enjoy More Relevant Blogs
How Much Does Rear Glass Replacement Cost for Mitsubishi Xpander Cross? Pricing Factors, OEM vs Aftermarket, and Insurance Deductibles
Estimate Mitsubishi Xpander Cross rear glass replacement cost. Compare OEM vs aftermarket, labor factors, insurance deductibles, and ways to save. Request a quote.
Rear Glass Replacement for Mitsubishi Xpander Cross: What to Expect During Install and Aftercare
Rear glass replacement for Mitsubishi Xpander Cross: what happens during install, defroster and tint considerations, cure time, and aftercare to prevent leaks long-term.
How Long Does Rear Glass Replacement Take on Mitsubishi Xpander Cross? Install Time, Adhesive Cure Time, and When It’s Safe to Drive
How long is Mitsubishi Xpander Cross rear glass replacement? Get install time, urethane cure guidelines, and drive-away timing after service. Plan your visit today.
How to Schedule Mobile Rear Glass Replacement for Mitsubishi Xpander Cross
Schedule mobile rear glass replacement for your Mitsubishi Xpander Cross in minutes. Learn what info to provide, how long it takes, and prep tips for service day.
Tempered Safety Rear Glass Replacement for Mitsubishi Xpander Cross: Understanding DOT Markings and FMVSS 205
Need Mitsubishi Xpander Cross rear glass replacement? Learn tempered safety glass basics, DOT markings, and FMVSS 205, plus install and cure tips. Get a quote today.
Shattered Back Window on Mitsubishi Xpander Cross: A Step-by-Step Rear Glass Replacement Plan
Shattered back window on Mitsubishi Xpander Cross? Follow a step-by-step rear glass replacement plan, cleanup tips, defroster notes, cure time, and drive-away rules.
Rear Defroster Not Working on Mitsubishi Xpander Cross? When Rear Glass Replacement Makes More Sense Than Repair
Rear defroster not working on your Mitsubishi Xpander Cross? Learn common causes, when repair fails, and when rear glass replacement is the smarter fix for winter.
Back Glass Replacement on Mitsubishi Xpander Cross: Defroster Tabs, Antenna Lines, and Connector Reattachment Basics
Back glass replacement on Mitsubishi Xpander Cross: defroster tabs, antenna lines, and connectors explained, plus install tips to avoid damage and rework safely.
Post-Install Checks for Mitsubishi Xpander Cross: Rear Glass Replacement Wind Noise, Leaks, and Rattle Tests
Post-install rear glass checks for Mitsubishi Xpander Cross: test for wind noise, leaks, and rattles, plus when to return for warranty service—check today before trips.
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm