Services
Service Areas
Cleanup After Quarter Window Breakage on Nissan Navara: Safe Glass Removal and Interior Protection
When a quarter window breaks on your Nissan Navara, the quickest way to create lingering problems is rushing cleanup. Quarter glass is tempered, so it shatters into small “pebbles” that hide in carpet, seat tracks, door pockets, and trim seams. Treat every fragment as a safety issue. Start with protection: cut-resistant gloves and eye protection, and keep kids and pets away. Lift out larger pieces from the frame and lower sill—never press down on the pile. Scoop with a dustpan or stiff cardboard, then vacuum with a hose and crevice tool, working from trim down through seats, carpet, floor mats, and the cargo area. Avoid hard sweeping that pushes fines deeper. Finish upholstery with wide tape or a lint roller to lift tiny shards you cannot see, and wipe hard plastics with a damp microfiber to trap remaining grit. If you need a temporary cover, tape plastic sheeting from the inside using painter’s tape for a tight, weather-resistant seal that won’t pull paint. Then book Bang AutoGlass for mobile quarter window replacement: we arrive with the right quarter glass, perform a final interior glass sweep, and restore your Nissan Navara to a safe, weather-tight daily driver—often as soon as next day.
Verify the Correct Quarter Glass for Nissan Navara: Fixed vs Pop-Out, Tint Match, and DOT Markings
Before installing a new quarter window on your Nissan Navara, we verify exact fitment, because an “almost right” piece can cause leaks, wind noise, trim gaps, or a tint mismatch that’s obvious in daylight. First we confirm the quarter glass style: fixed glass bonded with urethane versus a pop-out/vent unit with hinges or latches. We match your Nissan Navara body style, model-year range, and left/right orientation. Next we align appearance and solar performance—clear versus factory privacy tint, shade consistency, and how any existing window film will blend so the replacement doesn’t stand out. We also check the glass “bug” markings: DOT codes, safety identifiers, manufacturer traceability, and the correct AS rating for non-windshield glazing. Many quarter windows arrive as an encapsulated assembly with pre-attached molding, studs, locator pins, or clips; those details control seating depth, reveal lines, and how interior panels lock back in. When applicable, we confirm embedded features such as antenna elements. The result is an OEM-correct Nissan Navara quarter window replacement that seals properly. If comprehensive insurance applies, Bang AutoGlass works with all insurance companies and can help you complete the claim steps on-site.
Remove Trim and Old Glass: Nissan Navara Quarter Window Replacement Disassembly Checklist
Quarter window replacement on a Nissan Navara depends on controlled access: remove only what’s necessary, protect painted edges, and keep clips intact so the car goes back together without rattles. We start by stabilizing the work area—powering down accessories, opening another door or window to reduce pressure changes, and masking adjacent paint, weatherstrips, and trim. From inside the vehicle, we move the minimum panels needed (often a rear seat bolster, quarter trim, and cargo-side panels), using non-marring tools and organizing hardware so every fastener returns to its original location. We work carefully around seatbelt anchors and curtain airbag zones to avoid damage and warning lights. Release method depends on the Nissan Navara design: bonded glass is separated by cutting the urethane bead cleanly without gouging the pinchweld or bending the flange; bolt-in or framed styles require supporting the glass as retainers are removed to prevent a sudden drop. After removal, we re-vacuum the cavity, address any damaged molding, and prep the opening for installation. Most mobile replacements take about 30–45 minutes for the swap, followed by adhesive cure time before safe drive-away.
Prep the Pinchweld and Bond Area: Corrosion Checks, Primers, and Adhesion Readiness
Prep is the quiet step that prevents loud problems later—wind noise, leaks, and rust after your Nissan Navara quarter window replacement. With bonded quarter glass, the critical surfaces are the pinchweld and the glass bond band, and both must be ready for urethane to achieve full strength. We inspect the opening for corrosion, old adhesive quality, and signs of prior bodywork that can affect fit and sealing. If we find bubbling paint or rust, we address it per refinish standards so the flange is stable, while avoiding unnecessary grinding that removes factory coatings. Next, the old urethane is reduced to a consistent, thin base layer so new urethane can chemically and mechanically bond to it. Any exposed bare metal—whether from minor damage or a previous cut—is treated and primed appropriately, and pinchweld primer is applied when the adhesive system calls for it. On the glass itself, we clean the bond area thoroughly and apply activator/primer as required to improve adhesion and provide UV protection at the bond line. Throughout the process, contamination control is strict: no household cleaners, no silicone, and no shortcuts on dry/flash times, since those are common causes of edge lifts and long-term seepage. Before final set, we test-fit the quarter glass to verify alignment, locator engagement, and molding contact, then mask the perimeter to keep the finished edge uniform. Done correctly, your Nissan Navara gets an OEM-style seal that resists water intrusion and slows corrosion over time.
Urethane Bonding and Minimum Drive-Away Time for Nissan Navara: SDAT Factors You Must Follow
Once the pinchweld is ready, urethane application dictates performance for your Nissan Navara: sealing, noise control, and long-term durability. We apply high-quality automotive urethane in a consistent, uninterrupted bead sized to the required stand-off so the quarter glass sits at the correct height relative to the body and surrounding trim. Continuity matters most at corners and transitions, where thin spots can become leak paths. After the bead is laid, we set the glass onto locator pins or stops, align it to the reveal line, and confirm uniform contact around the perimeter without shifting the bead. We then stabilize the glass and verify moldings or encapsulation are seated correctly so they do not lift while curing begins. From there, we follow Safe Drive-Away Time (SDAT) requirements for the specific adhesive system and on-site conditions. Temperature and humidity materially affect cure rate: cold, dry air typically extends cure time, while warmer, humid conditions generally shorten it, so the correct approach is to install to spec and respect published SDAT guidance. As a conservative baseline, we recommend at least one hour before driving your Nissan Navara after the quarter window replacement is completed. During early cure, avoid door slams and rough roads, and do not use a pressurized wash for 24–48 hours. When bonding is done correctly and SDAT is honored, the result is a quiet cabin, a clean reveal, and a seal that holds.
Final Quality Checks: Leak Test, Wind Noise, Trim Fit, and Documentation for Nissan Navara
Before your Nissan Navara leaves our care, we run a structured quality-control sequence so the quarter window replacement performs as intended. First, we verify fit and appearance: the glass should be centered, reveal lines should mirror the opposite side, and any molding or encapsulation must sit flush with no lifted corners, gaps, or uneven edges. We check for proper urethane contact and ensure there is no contamination or excessive squeeze-out that could interfere with trim seating. Next, we reassemble interior panels and confirm clip engagement to prevent future buzzes, rattles, or loose trim in the quarter and cargo area. Leak prevention is validated with a controlled water test along the perimeter while we observe inside for intrusion into the quarter cavity or cargo area. If wind noise is a concern, we evaluate sealing consistency and trim contact, since small edge gaps can be audible at highway speed. We then clean the glass and ensure surrounding paint and trim are returned clean and residue-free. Finally, we document the job details—part verification, DOT markings, and install notes—and review aftercare: honoring the minimum one-hour safe drive-away time, avoiding door slams during early cure, and postponing high-pressure washes for 24–48 hours. Your paperwork also reflects our lifetime workmanship warranty for peace of mind. If you are processing an insurance claim, we can assist with any insurer as long as comprehensive coverage applies. The outcome is a Nissan Navara quarter window replacement that looks right, seals right, and is supported with clear documentation.
Services
Service Areas
Cleanup After Quarter Window Breakage on Nissan Navara: Safe Glass Removal and Interior Protection
When a quarter window breaks on your Nissan Navara, the quickest way to create lingering problems is rushing cleanup. Quarter glass is tempered, so it shatters into small “pebbles” that hide in carpet, seat tracks, door pockets, and trim seams. Treat every fragment as a safety issue. Start with protection: cut-resistant gloves and eye protection, and keep kids and pets away. Lift out larger pieces from the frame and lower sill—never press down on the pile. Scoop with a dustpan or stiff cardboard, then vacuum with a hose and crevice tool, working from trim down through seats, carpet, floor mats, and the cargo area. Avoid hard sweeping that pushes fines deeper. Finish upholstery with wide tape or a lint roller to lift tiny shards you cannot see, and wipe hard plastics with a damp microfiber to trap remaining grit. If you need a temporary cover, tape plastic sheeting from the inside using painter’s tape for a tight, weather-resistant seal that won’t pull paint. Then book Bang AutoGlass for mobile quarter window replacement: we arrive with the right quarter glass, perform a final interior glass sweep, and restore your Nissan Navara to a safe, weather-tight daily driver—often as soon as next day.
Verify the Correct Quarter Glass for Nissan Navara: Fixed vs Pop-Out, Tint Match, and DOT Markings
Before installing a new quarter window on your Nissan Navara, we verify exact fitment, because an “almost right” piece can cause leaks, wind noise, trim gaps, or a tint mismatch that’s obvious in daylight. First we confirm the quarter glass style: fixed glass bonded with urethane versus a pop-out/vent unit with hinges or latches. We match your Nissan Navara body style, model-year range, and left/right orientation. Next we align appearance and solar performance—clear versus factory privacy tint, shade consistency, and how any existing window film will blend so the replacement doesn’t stand out. We also check the glass “bug” markings: DOT codes, safety identifiers, manufacturer traceability, and the correct AS rating for non-windshield glazing. Many quarter windows arrive as an encapsulated assembly with pre-attached molding, studs, locator pins, or clips; those details control seating depth, reveal lines, and how interior panels lock back in. When applicable, we confirm embedded features such as antenna elements. The result is an OEM-correct Nissan Navara quarter window replacement that seals properly. If comprehensive insurance applies, Bang AutoGlass works with all insurance companies and can help you complete the claim steps on-site.
Remove Trim and Old Glass: Nissan Navara Quarter Window Replacement Disassembly Checklist
Quarter window replacement on a Nissan Navara depends on controlled access: remove only what’s necessary, protect painted edges, and keep clips intact so the car goes back together without rattles. We start by stabilizing the work area—powering down accessories, opening another door or window to reduce pressure changes, and masking adjacent paint, weatherstrips, and trim. From inside the vehicle, we move the minimum panels needed (often a rear seat bolster, quarter trim, and cargo-side panels), using non-marring tools and organizing hardware so every fastener returns to its original location. We work carefully around seatbelt anchors and curtain airbag zones to avoid damage and warning lights. Release method depends on the Nissan Navara design: bonded glass is separated by cutting the urethane bead cleanly without gouging the pinchweld or bending the flange; bolt-in or framed styles require supporting the glass as retainers are removed to prevent a sudden drop. After removal, we re-vacuum the cavity, address any damaged molding, and prep the opening for installation. Most mobile replacements take about 30–45 minutes for the swap, followed by adhesive cure time before safe drive-away.
Prep the Pinchweld and Bond Area: Corrosion Checks, Primers, and Adhesion Readiness
Prep is the quiet step that prevents loud problems later—wind noise, leaks, and rust after your Nissan Navara quarter window replacement. With bonded quarter glass, the critical surfaces are the pinchweld and the glass bond band, and both must be ready for urethane to achieve full strength. We inspect the opening for corrosion, old adhesive quality, and signs of prior bodywork that can affect fit and sealing. If we find bubbling paint or rust, we address it per refinish standards so the flange is stable, while avoiding unnecessary grinding that removes factory coatings. Next, the old urethane is reduced to a consistent, thin base layer so new urethane can chemically and mechanically bond to it. Any exposed bare metal—whether from minor damage or a previous cut—is treated and primed appropriately, and pinchweld primer is applied when the adhesive system calls for it. On the glass itself, we clean the bond area thoroughly and apply activator/primer as required to improve adhesion and provide UV protection at the bond line. Throughout the process, contamination control is strict: no household cleaners, no silicone, and no shortcuts on dry/flash times, since those are common causes of edge lifts and long-term seepage. Before final set, we test-fit the quarter glass to verify alignment, locator engagement, and molding contact, then mask the perimeter to keep the finished edge uniform. Done correctly, your Nissan Navara gets an OEM-style seal that resists water intrusion and slows corrosion over time.
Urethane Bonding and Minimum Drive-Away Time for Nissan Navara: SDAT Factors You Must Follow
Once the pinchweld is ready, urethane application dictates performance for your Nissan Navara: sealing, noise control, and long-term durability. We apply high-quality automotive urethane in a consistent, uninterrupted bead sized to the required stand-off so the quarter glass sits at the correct height relative to the body and surrounding trim. Continuity matters most at corners and transitions, where thin spots can become leak paths. After the bead is laid, we set the glass onto locator pins or stops, align it to the reveal line, and confirm uniform contact around the perimeter without shifting the bead. We then stabilize the glass and verify moldings or encapsulation are seated correctly so they do not lift while curing begins. From there, we follow Safe Drive-Away Time (SDAT) requirements for the specific adhesive system and on-site conditions. Temperature and humidity materially affect cure rate: cold, dry air typically extends cure time, while warmer, humid conditions generally shorten it, so the correct approach is to install to spec and respect published SDAT guidance. As a conservative baseline, we recommend at least one hour before driving your Nissan Navara after the quarter window replacement is completed. During early cure, avoid door slams and rough roads, and do not use a pressurized wash for 24–48 hours. When bonding is done correctly and SDAT is honored, the result is a quiet cabin, a clean reveal, and a seal that holds.
Final Quality Checks: Leak Test, Wind Noise, Trim Fit, and Documentation for Nissan Navara
Before your Nissan Navara leaves our care, we run a structured quality-control sequence so the quarter window replacement performs as intended. First, we verify fit and appearance: the glass should be centered, reveal lines should mirror the opposite side, and any molding or encapsulation must sit flush with no lifted corners, gaps, or uneven edges. We check for proper urethane contact and ensure there is no contamination or excessive squeeze-out that could interfere with trim seating. Next, we reassemble interior panels and confirm clip engagement to prevent future buzzes, rattles, or loose trim in the quarter and cargo area. Leak prevention is validated with a controlled water test along the perimeter while we observe inside for intrusion into the quarter cavity or cargo area. If wind noise is a concern, we evaluate sealing consistency and trim contact, since small edge gaps can be audible at highway speed. We then clean the glass and ensure surrounding paint and trim are returned clean and residue-free. Finally, we document the job details—part verification, DOT markings, and install notes—and review aftercare: honoring the minimum one-hour safe drive-away time, avoiding door slams during early cure, and postponing high-pressure washes for 24–48 hours. Your paperwork also reflects our lifetime workmanship warranty for peace of mind. If you are processing an insurance claim, we can assist with any insurer as long as comprehensive coverage applies. The outcome is a Nissan Navara quarter window replacement that looks right, seals right, and is supported with clear documentation.
Services
Service Areas
Cleanup After Quarter Window Breakage on Nissan Navara: Safe Glass Removal and Interior Protection
When a quarter window breaks on your Nissan Navara, the quickest way to create lingering problems is rushing cleanup. Quarter glass is tempered, so it shatters into small “pebbles” that hide in carpet, seat tracks, door pockets, and trim seams. Treat every fragment as a safety issue. Start with protection: cut-resistant gloves and eye protection, and keep kids and pets away. Lift out larger pieces from the frame and lower sill—never press down on the pile. Scoop with a dustpan or stiff cardboard, then vacuum with a hose and crevice tool, working from trim down through seats, carpet, floor mats, and the cargo area. Avoid hard sweeping that pushes fines deeper. Finish upholstery with wide tape or a lint roller to lift tiny shards you cannot see, and wipe hard plastics with a damp microfiber to trap remaining grit. If you need a temporary cover, tape plastic sheeting from the inside using painter’s tape for a tight, weather-resistant seal that won’t pull paint. Then book Bang AutoGlass for mobile quarter window replacement: we arrive with the right quarter glass, perform a final interior glass sweep, and restore your Nissan Navara to a safe, weather-tight daily driver—often as soon as next day.
Verify the Correct Quarter Glass for Nissan Navara: Fixed vs Pop-Out, Tint Match, and DOT Markings
Before installing a new quarter window on your Nissan Navara, we verify exact fitment, because an “almost right” piece can cause leaks, wind noise, trim gaps, or a tint mismatch that’s obvious in daylight. First we confirm the quarter glass style: fixed glass bonded with urethane versus a pop-out/vent unit with hinges or latches. We match your Nissan Navara body style, model-year range, and left/right orientation. Next we align appearance and solar performance—clear versus factory privacy tint, shade consistency, and how any existing window film will blend so the replacement doesn’t stand out. We also check the glass “bug” markings: DOT codes, safety identifiers, manufacturer traceability, and the correct AS rating for non-windshield glazing. Many quarter windows arrive as an encapsulated assembly with pre-attached molding, studs, locator pins, or clips; those details control seating depth, reveal lines, and how interior panels lock back in. When applicable, we confirm embedded features such as antenna elements. The result is an OEM-correct Nissan Navara quarter window replacement that seals properly. If comprehensive insurance applies, Bang AutoGlass works with all insurance companies and can help you complete the claim steps on-site.
Remove Trim and Old Glass: Nissan Navara Quarter Window Replacement Disassembly Checklist
Quarter window replacement on a Nissan Navara depends on controlled access: remove only what’s necessary, protect painted edges, and keep clips intact so the car goes back together without rattles. We start by stabilizing the work area—powering down accessories, opening another door or window to reduce pressure changes, and masking adjacent paint, weatherstrips, and trim. From inside the vehicle, we move the minimum panels needed (often a rear seat bolster, quarter trim, and cargo-side panels), using non-marring tools and organizing hardware so every fastener returns to its original location. We work carefully around seatbelt anchors and curtain airbag zones to avoid damage and warning lights. Release method depends on the Nissan Navara design: bonded glass is separated by cutting the urethane bead cleanly without gouging the pinchweld or bending the flange; bolt-in or framed styles require supporting the glass as retainers are removed to prevent a sudden drop. After removal, we re-vacuum the cavity, address any damaged molding, and prep the opening for installation. Most mobile replacements take about 30–45 minutes for the swap, followed by adhesive cure time before safe drive-away.
Prep the Pinchweld and Bond Area: Corrosion Checks, Primers, and Adhesion Readiness
Prep is the quiet step that prevents loud problems later—wind noise, leaks, and rust after your Nissan Navara quarter window replacement. With bonded quarter glass, the critical surfaces are the pinchweld and the glass bond band, and both must be ready for urethane to achieve full strength. We inspect the opening for corrosion, old adhesive quality, and signs of prior bodywork that can affect fit and sealing. If we find bubbling paint or rust, we address it per refinish standards so the flange is stable, while avoiding unnecessary grinding that removes factory coatings. Next, the old urethane is reduced to a consistent, thin base layer so new urethane can chemically and mechanically bond to it. Any exposed bare metal—whether from minor damage or a previous cut—is treated and primed appropriately, and pinchweld primer is applied when the adhesive system calls for it. On the glass itself, we clean the bond area thoroughly and apply activator/primer as required to improve adhesion and provide UV protection at the bond line. Throughout the process, contamination control is strict: no household cleaners, no silicone, and no shortcuts on dry/flash times, since those are common causes of edge lifts and long-term seepage. Before final set, we test-fit the quarter glass to verify alignment, locator engagement, and molding contact, then mask the perimeter to keep the finished edge uniform. Done correctly, your Nissan Navara gets an OEM-style seal that resists water intrusion and slows corrosion over time.
Urethane Bonding and Minimum Drive-Away Time for Nissan Navara: SDAT Factors You Must Follow
Once the pinchweld is ready, urethane application dictates performance for your Nissan Navara: sealing, noise control, and long-term durability. We apply high-quality automotive urethane in a consistent, uninterrupted bead sized to the required stand-off so the quarter glass sits at the correct height relative to the body and surrounding trim. Continuity matters most at corners and transitions, where thin spots can become leak paths. After the bead is laid, we set the glass onto locator pins or stops, align it to the reveal line, and confirm uniform contact around the perimeter without shifting the bead. We then stabilize the glass and verify moldings or encapsulation are seated correctly so they do not lift while curing begins. From there, we follow Safe Drive-Away Time (SDAT) requirements for the specific adhesive system and on-site conditions. Temperature and humidity materially affect cure rate: cold, dry air typically extends cure time, while warmer, humid conditions generally shorten it, so the correct approach is to install to spec and respect published SDAT guidance. As a conservative baseline, we recommend at least one hour before driving your Nissan Navara after the quarter window replacement is completed. During early cure, avoid door slams and rough roads, and do not use a pressurized wash for 24–48 hours. When bonding is done correctly and SDAT is honored, the result is a quiet cabin, a clean reveal, and a seal that holds.
Final Quality Checks: Leak Test, Wind Noise, Trim Fit, and Documentation for Nissan Navara
Before your Nissan Navara leaves our care, we run a structured quality-control sequence so the quarter window replacement performs as intended. First, we verify fit and appearance: the glass should be centered, reveal lines should mirror the opposite side, and any molding or encapsulation must sit flush with no lifted corners, gaps, or uneven edges. We check for proper urethane contact and ensure there is no contamination or excessive squeeze-out that could interfere with trim seating. Next, we reassemble interior panels and confirm clip engagement to prevent future buzzes, rattles, or loose trim in the quarter and cargo area. Leak prevention is validated with a controlled water test along the perimeter while we observe inside for intrusion into the quarter cavity or cargo area. If wind noise is a concern, we evaluate sealing consistency and trim contact, since small edge gaps can be audible at highway speed. We then clean the glass and ensure surrounding paint and trim are returned clean and residue-free. Finally, we document the job details—part verification, DOT markings, and install notes—and review aftercare: honoring the minimum one-hour safe drive-away time, avoiding door slams during early cure, and postponing high-pressure washes for 24–48 hours. Your paperwork also reflects our lifetime workmanship warranty for peace of mind. If you are processing an insurance claim, we can assist with any insurer as long as comprehensive coverage applies. The outcome is a Nissan Navara quarter window replacement that looks right, seals right, and is supported with clear documentation.
Enjoy More Relevant Blogs
How to Schedule Mobile Quarter Glass Replacement for Nissan Navara
Need mobile quarter glass replacement for Nissan Navara? Follow our scheduling checklist, photos to take, timing, and on-site tips to restore security.
How Long After Nissan Navara Quarter Panel Glass Replacement Can You Drive or Wash the Car? Urethane Cure-Time Rules
After Nissan Navara quarter panel glass replacement, learn safe drive-away time, when to wash, and urethane cure rules that help prevent leaks and wind noise.
Fixed Quarter Window vs Vent Glass on Nissan Navara: Ordering the Correct Replacement
Fixed quarter window vs vent glass on Nissan Navara: how to identify yours and order the correct replacement for fit, sealing, and safety—read this now.
Safety Standards Explained: DOT Markings and FMVSS 205 for Nissan Navara Quarter Glass Replacement
DOT markings and FMVSS 205 explained for Nissan Navara quarter glass replacement—how to verify safety markings and choose compliant OEM-quality glass.
OEM-Quality Quarter Glass Replacement for Nissan Navara: Fit, Trim, and Weather-Seal Checklist
OEM-quality quarter glass replacement for Nissan Navara: fit, trim, and weather-seal checklist for correct install, leak prevention, and clean finish.
Tint & Privacy Glass Match Guide: Nissan Navara Quarter Glass Replacement Done Right
Tint and privacy match guide for Nissan Navara quarter glass replacement—how to match shade, markings, and fit so the new glass looks factory-perfect.
How Much Does Nissan Navara Quarter Panel Glass Replacement Cost? Insurance Deductibles, Estimates, and Ways to Save
Cost to replace Nissan Navara quarter panel glass: key price factors, OEM vs aftermarket options, insurance deductibles, estimates, and smart ways to save.
Stop Leaks and Wind Noise: What Proper Nissan Navara Quarter Glass Replacement Should Prevent
Stop leaks and wind noise with proper Nissan Navara quarter glass replacement. Learn what correct fit, sealing, and trim should prevent after install.
After a Break-In: Nissan Navara Quarter Glass Replacement Plan to Restore Security and Visibility
After a break-in on Nissan Navara, restore security with a quarter glass replacement plan: cleanup, temporary protection, scheduling, and post-install checks.
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm