Services
Service Areas
Mobile ADAS Calibration for Volkswagen T-Roc: What to Expect On-Site and Why Setup Matters
Confirm Volkswagen T-Roc Calibration Requirements and Which ADAS Systems Are Involved
Planning mobile ADAS Calibration for a Volkswagen T-Roc begins with a requirements check tied to the vehicle's actual ADAS configuration, not a generic assumption based on a dash message. Depending on options, the Volkswagen T-Roc may rely on a windshield camera, front radar, side or corner radars, ultrasonics, and stability-related inputs that together control lane assistance, adaptive cruise, and automatic braking. The triggering event is the roadmap: windshield replacement, camera mount service, bumper removal, front-end repair, alignment changes, suspension work, module programming, or stored DTCs can each demand different routines. The most reliable approach is to identify which modules are requesting calibration, then confirm whether the OEM procedure is static, dynamic, or both. That up-front decision clarifies mobile needs such as target type, required distances, measurement tools, and battery support, and it prevents half-finished outcomes where one routine passes but another remains pending. Baseline integrity matters: a loose camera mount, shifted radar bracket, obstructed sensor face, or dirty glass can cause the system to learn the wrong reference. Finally, the site must support level ground, adequate space, consistent lighting, and, when required, nearby roads with clear lane markings. If those conditions are not available, relocating or rescheduling protects safety and reduces repeat visits for the Volkswagen T-Roc.
Mobile ADAS Calibration Types for Volkswagen T-Roc: Static, Dynamic, or Both
Mobile ADAS Calibration for a Volkswagen T-Roc typically falls into three buckets: static calibration, dynamic calibration, or a workflow that requires both. Static calibration is performed with the vehicle parked while OEM targets are placed at defined heights, distances, and centerline offsets so the camera or radar module can compute aim, pitch, and horizon references. Dynamic calibration completes during a drive where the Volkswagen T-Roc uses lane markings and stable motion to learn offsets and confirm plausibility, often within specific speed bands and a minimum drive time or distance. Some platforms require both methods, such as a static baseline followed by a dynamic verification drive, or separate static routines for camera and radar plus initialization of steering angle or stability references. From a mobile standpoint, static work is about controlling the environment: flat surface, sufficient lot depth for target distance, stable lighting, and precise measurement tools. Dynamic work is about controlling the route: clear lane lines, predictable traffic, and a safe ability to maintain speed and lane position until completion. Weather and visibility can delay dynamic completion even when the routine starts, so we plan accordingly. Regardless of type, the goal is a completed status and documented post-scan, not simply turning off a warning light on the Volkswagen T-Roc.
On-Site Setup Matters: Level Surface, Space, Lighting, and Target Distances
For mobile ADAS Calibration, the area around a Volkswagen T-Roc must function like a temporary calibration bay, because small environmental errors can become aiming errors. Level ground is the first requirement for static routines; a sloped driveway or crowned street can skew camera pitch and radar aim. We stabilize the vehicle stance by setting tire pressures evenly and confirming normal ride height and loading before measurements begin. Space is the next constraint. Targets must be placed at exact distances and offsets relative to a true centerline, and the sensors need a clear, uninterrupted field of view. Walls, poles, parked cars, and reflective surfaces can intrude into the target scene and corrupt the reference image. Lighting affects camera-based calibrations; strong sunrise or sunset glare, harsh shadow edges, and uneven illumination can reduce contrast and cause failures or inaccurate learning. Radar steps add sensitivity to nearby metal enclosures, large doors, and moving equipment that can create reflections. Weather also matters: wind can move targets, rain reduces lane visibility for dynamic phases, and extreme heat can affect equipment stability. If a dynamic drive is required, we select a nearby route with consistent markings so the Volkswagen T-Roc can meet completion criteria without repeated interruptions.
Pre-Calibration Checklist for Volkswagen T-Roc: Pre-Scan, DTC Review, and Vehicle Readiness
A consistent pre-calibration checklist makes mobile ADAS Calibration on a Volkswagen T-Roc predictable, starting with a full pre-scan. The scan captures DTCs, module status, and clues to blockers like voltage drops, communication faults, or sensor errors. Then verify geometry prerequisites: correct tire size, equal pressures, normal ride height, and no unusual cargo or suspension changes that tilt the chassis. Alignment is often required because toe and thrust angle affect straight-ahead reference; calibrating before alignment is corrected can teach the Volkswagen T-Roc the wrong centerline. Stabilize power next. Mobile sessions can keep ignition on for extended periods, so battery support helps prevent interruptions and false codes. After glass or front-end work, confirm the windshield is seated correctly, the camera bracket/cover is secure, and the camera viewing area is clean. Inspect radar and other sensors for proper mounting and unobstructed fields of view, especially after bumper removal. Also resolve steering angle or stability-control faults, which can prevent ADAS Calibration from starting even with perfect targets. If dynamic steps are required, confirm the vehicle is safe to drive and nearby roads have clear lane markings and steady-speed conditions. Doing this up front reduces rework and produces a defensible post-scan record.
What to Expect During On-Site Calibration: Target Alignment, Scan Tool Steps, and Road Procedure
During mobile ADAS Calibration for a Volkswagen T-Roc, the appointment follows a scan-guided sequence that controls both vehicle state and calibration order. We start by selecting the correct routine in the scan tool, confirming the module(s) involved, and placing the system into service mode so driver-assist features are ready for recalibration. For static steps, the Volkswagen T-Roc is positioned precisely, a centerline reference is established, and targets are placed using measured distances and heights. The scan tool prompts actions such as steering centering, brake holds, ignition cycles, and measurement confirmations while the module captures reference images/returns and computes offsets. Precision is what makes the calibration durable. Small errors in yaw, target height, or distance can later present as lane-centering bias, false alerts, or restricted adaptive cruise. If the procedure includes a dynamic phase, it follows only after the stationary step is accepted. Dynamic calibration is a controlled drive where the Volkswagen T-Roc must maintain specified speeds with clear lane markings until the tool indicates completion; congestion and poor markings can pause progress. Throughout the workflow, newly set DTCs are treated as diagnostic signals—obstruction, voltage instability, mounting issues, or unmet prerequisites—rather than something to clear and ignore. Once complete, a post-scan confirms clean module health, cleared warnings, and normal feature availability.
Proof and Documentation: Post-Scan Results, Verification, and Records for Volkswagen T-Roc
Proof and documentation close out mobile ADAS Calibration on a Volkswagen T-Roc, providing objective evidence that required routines were completed. A strong closeout includes a post-scan report showing which modules were checked, which DTCs existed before service, and whether any calibration-related faults remain afterward. It should also list the completed routines—forward camera calibration, radar aiming/verification, steering angle initialization, or sensor-fusion validation—so scope is clear. When possible, record the scan-tool routine name and completion status for the specific Volkswagen T-Roc configuration. These records matter beyond today’s visit. They establish a “known good” baseline that helps after later alignment work, suspension changes, another windshield replacement, or additional repairs that affect sensor geometry. They also support claims by showing ADAS Calibration was performed as a required step after glass or front-end work, not simply by clearing codes. Good documentation includes date/time, technician identification, method used (static, dynamic, or both), and brief notes on on-site prerequisites (level surface, tire pressures normalized, battery support used). If a dynamic drive was required, noting general completion conditions can explain why the routine passed. Finally, confirm warnings are off and features can be enabled; if completion isn’t possible, document the limiting factor and the next-step recommendation.
Services
Service Areas
Mobile ADAS Calibration for Volkswagen T-Roc: What to Expect On-Site and Why Setup Matters
Confirm Volkswagen T-Roc Calibration Requirements and Which ADAS Systems Are Involved
Planning mobile ADAS Calibration for a Volkswagen T-Roc begins with a requirements check tied to the vehicle's actual ADAS configuration, not a generic assumption based on a dash message. Depending on options, the Volkswagen T-Roc may rely on a windshield camera, front radar, side or corner radars, ultrasonics, and stability-related inputs that together control lane assistance, adaptive cruise, and automatic braking. The triggering event is the roadmap: windshield replacement, camera mount service, bumper removal, front-end repair, alignment changes, suspension work, module programming, or stored DTCs can each demand different routines. The most reliable approach is to identify which modules are requesting calibration, then confirm whether the OEM procedure is static, dynamic, or both. That up-front decision clarifies mobile needs such as target type, required distances, measurement tools, and battery support, and it prevents half-finished outcomes where one routine passes but another remains pending. Baseline integrity matters: a loose camera mount, shifted radar bracket, obstructed sensor face, or dirty glass can cause the system to learn the wrong reference. Finally, the site must support level ground, adequate space, consistent lighting, and, when required, nearby roads with clear lane markings. If those conditions are not available, relocating or rescheduling protects safety and reduces repeat visits for the Volkswagen T-Roc.
Mobile ADAS Calibration Types for Volkswagen T-Roc: Static, Dynamic, or Both
Mobile ADAS Calibration for a Volkswagen T-Roc typically falls into three buckets: static calibration, dynamic calibration, or a workflow that requires both. Static calibration is performed with the vehicle parked while OEM targets are placed at defined heights, distances, and centerline offsets so the camera or radar module can compute aim, pitch, and horizon references. Dynamic calibration completes during a drive where the Volkswagen T-Roc uses lane markings and stable motion to learn offsets and confirm plausibility, often within specific speed bands and a minimum drive time or distance. Some platforms require both methods, such as a static baseline followed by a dynamic verification drive, or separate static routines for camera and radar plus initialization of steering angle or stability references. From a mobile standpoint, static work is about controlling the environment: flat surface, sufficient lot depth for target distance, stable lighting, and precise measurement tools. Dynamic work is about controlling the route: clear lane lines, predictable traffic, and a safe ability to maintain speed and lane position until completion. Weather and visibility can delay dynamic completion even when the routine starts, so we plan accordingly. Regardless of type, the goal is a completed status and documented post-scan, not simply turning off a warning light on the Volkswagen T-Roc.
On-Site Setup Matters: Level Surface, Space, Lighting, and Target Distances
For mobile ADAS Calibration, the area around a Volkswagen T-Roc must function like a temporary calibration bay, because small environmental errors can become aiming errors. Level ground is the first requirement for static routines; a sloped driveway or crowned street can skew camera pitch and radar aim. We stabilize the vehicle stance by setting tire pressures evenly and confirming normal ride height and loading before measurements begin. Space is the next constraint. Targets must be placed at exact distances and offsets relative to a true centerline, and the sensors need a clear, uninterrupted field of view. Walls, poles, parked cars, and reflective surfaces can intrude into the target scene and corrupt the reference image. Lighting affects camera-based calibrations; strong sunrise or sunset glare, harsh shadow edges, and uneven illumination can reduce contrast and cause failures or inaccurate learning. Radar steps add sensitivity to nearby metal enclosures, large doors, and moving equipment that can create reflections. Weather also matters: wind can move targets, rain reduces lane visibility for dynamic phases, and extreme heat can affect equipment stability. If a dynamic drive is required, we select a nearby route with consistent markings so the Volkswagen T-Roc can meet completion criteria without repeated interruptions.
Pre-Calibration Checklist for Volkswagen T-Roc: Pre-Scan, DTC Review, and Vehicle Readiness
A consistent pre-calibration checklist makes mobile ADAS Calibration on a Volkswagen T-Roc predictable, starting with a full pre-scan. The scan captures DTCs, module status, and clues to blockers like voltage drops, communication faults, or sensor errors. Then verify geometry prerequisites: correct tire size, equal pressures, normal ride height, and no unusual cargo or suspension changes that tilt the chassis. Alignment is often required because toe and thrust angle affect straight-ahead reference; calibrating before alignment is corrected can teach the Volkswagen T-Roc the wrong centerline. Stabilize power next. Mobile sessions can keep ignition on for extended periods, so battery support helps prevent interruptions and false codes. After glass or front-end work, confirm the windshield is seated correctly, the camera bracket/cover is secure, and the camera viewing area is clean. Inspect radar and other sensors for proper mounting and unobstructed fields of view, especially after bumper removal. Also resolve steering angle or stability-control faults, which can prevent ADAS Calibration from starting even with perfect targets. If dynamic steps are required, confirm the vehicle is safe to drive and nearby roads have clear lane markings and steady-speed conditions. Doing this up front reduces rework and produces a defensible post-scan record.
What to Expect During On-Site Calibration: Target Alignment, Scan Tool Steps, and Road Procedure
During mobile ADAS Calibration for a Volkswagen T-Roc, the appointment follows a scan-guided sequence that controls both vehicle state and calibration order. We start by selecting the correct routine in the scan tool, confirming the module(s) involved, and placing the system into service mode so driver-assist features are ready for recalibration. For static steps, the Volkswagen T-Roc is positioned precisely, a centerline reference is established, and targets are placed using measured distances and heights. The scan tool prompts actions such as steering centering, brake holds, ignition cycles, and measurement confirmations while the module captures reference images/returns and computes offsets. Precision is what makes the calibration durable. Small errors in yaw, target height, or distance can later present as lane-centering bias, false alerts, or restricted adaptive cruise. If the procedure includes a dynamic phase, it follows only after the stationary step is accepted. Dynamic calibration is a controlled drive where the Volkswagen T-Roc must maintain specified speeds with clear lane markings until the tool indicates completion; congestion and poor markings can pause progress. Throughout the workflow, newly set DTCs are treated as diagnostic signals—obstruction, voltage instability, mounting issues, or unmet prerequisites—rather than something to clear and ignore. Once complete, a post-scan confirms clean module health, cleared warnings, and normal feature availability.
Proof and Documentation: Post-Scan Results, Verification, and Records for Volkswagen T-Roc
Proof and documentation close out mobile ADAS Calibration on a Volkswagen T-Roc, providing objective evidence that required routines were completed. A strong closeout includes a post-scan report showing which modules were checked, which DTCs existed before service, and whether any calibration-related faults remain afterward. It should also list the completed routines—forward camera calibration, radar aiming/verification, steering angle initialization, or sensor-fusion validation—so scope is clear. When possible, record the scan-tool routine name and completion status for the specific Volkswagen T-Roc configuration. These records matter beyond today’s visit. They establish a “known good” baseline that helps after later alignment work, suspension changes, another windshield replacement, or additional repairs that affect sensor geometry. They also support claims by showing ADAS Calibration was performed as a required step after glass or front-end work, not simply by clearing codes. Good documentation includes date/time, technician identification, method used (static, dynamic, or both), and brief notes on on-site prerequisites (level surface, tire pressures normalized, battery support used). If a dynamic drive was required, noting general completion conditions can explain why the routine passed. Finally, confirm warnings are off and features can be enabled; if completion isn’t possible, document the limiting factor and the next-step recommendation.
Services
Service Areas
Mobile ADAS Calibration for Volkswagen T-Roc: What to Expect On-Site and Why Setup Matters
Confirm Volkswagen T-Roc Calibration Requirements and Which ADAS Systems Are Involved
Planning mobile ADAS Calibration for a Volkswagen T-Roc begins with a requirements check tied to the vehicle's actual ADAS configuration, not a generic assumption based on a dash message. Depending on options, the Volkswagen T-Roc may rely on a windshield camera, front radar, side or corner radars, ultrasonics, and stability-related inputs that together control lane assistance, adaptive cruise, and automatic braking. The triggering event is the roadmap: windshield replacement, camera mount service, bumper removal, front-end repair, alignment changes, suspension work, module programming, or stored DTCs can each demand different routines. The most reliable approach is to identify which modules are requesting calibration, then confirm whether the OEM procedure is static, dynamic, or both. That up-front decision clarifies mobile needs such as target type, required distances, measurement tools, and battery support, and it prevents half-finished outcomes where one routine passes but another remains pending. Baseline integrity matters: a loose camera mount, shifted radar bracket, obstructed sensor face, or dirty glass can cause the system to learn the wrong reference. Finally, the site must support level ground, adequate space, consistent lighting, and, when required, nearby roads with clear lane markings. If those conditions are not available, relocating or rescheduling protects safety and reduces repeat visits for the Volkswagen T-Roc.
Mobile ADAS Calibration Types for Volkswagen T-Roc: Static, Dynamic, or Both
Mobile ADAS Calibration for a Volkswagen T-Roc typically falls into three buckets: static calibration, dynamic calibration, or a workflow that requires both. Static calibration is performed with the vehicle parked while OEM targets are placed at defined heights, distances, and centerline offsets so the camera or radar module can compute aim, pitch, and horizon references. Dynamic calibration completes during a drive where the Volkswagen T-Roc uses lane markings and stable motion to learn offsets and confirm plausibility, often within specific speed bands and a minimum drive time or distance. Some platforms require both methods, such as a static baseline followed by a dynamic verification drive, or separate static routines for camera and radar plus initialization of steering angle or stability references. From a mobile standpoint, static work is about controlling the environment: flat surface, sufficient lot depth for target distance, stable lighting, and precise measurement tools. Dynamic work is about controlling the route: clear lane lines, predictable traffic, and a safe ability to maintain speed and lane position until completion. Weather and visibility can delay dynamic completion even when the routine starts, so we plan accordingly. Regardless of type, the goal is a completed status and documented post-scan, not simply turning off a warning light on the Volkswagen T-Roc.
On-Site Setup Matters: Level Surface, Space, Lighting, and Target Distances
For mobile ADAS Calibration, the area around a Volkswagen T-Roc must function like a temporary calibration bay, because small environmental errors can become aiming errors. Level ground is the first requirement for static routines; a sloped driveway or crowned street can skew camera pitch and radar aim. We stabilize the vehicle stance by setting tire pressures evenly and confirming normal ride height and loading before measurements begin. Space is the next constraint. Targets must be placed at exact distances and offsets relative to a true centerline, and the sensors need a clear, uninterrupted field of view. Walls, poles, parked cars, and reflective surfaces can intrude into the target scene and corrupt the reference image. Lighting affects camera-based calibrations; strong sunrise or sunset glare, harsh shadow edges, and uneven illumination can reduce contrast and cause failures or inaccurate learning. Radar steps add sensitivity to nearby metal enclosures, large doors, and moving equipment that can create reflections. Weather also matters: wind can move targets, rain reduces lane visibility for dynamic phases, and extreme heat can affect equipment stability. If a dynamic drive is required, we select a nearby route with consistent markings so the Volkswagen T-Roc can meet completion criteria without repeated interruptions.
Pre-Calibration Checklist for Volkswagen T-Roc: Pre-Scan, DTC Review, and Vehicle Readiness
A consistent pre-calibration checklist makes mobile ADAS Calibration on a Volkswagen T-Roc predictable, starting with a full pre-scan. The scan captures DTCs, module status, and clues to blockers like voltage drops, communication faults, or sensor errors. Then verify geometry prerequisites: correct tire size, equal pressures, normal ride height, and no unusual cargo or suspension changes that tilt the chassis. Alignment is often required because toe and thrust angle affect straight-ahead reference; calibrating before alignment is corrected can teach the Volkswagen T-Roc the wrong centerline. Stabilize power next. Mobile sessions can keep ignition on for extended periods, so battery support helps prevent interruptions and false codes. After glass or front-end work, confirm the windshield is seated correctly, the camera bracket/cover is secure, and the camera viewing area is clean. Inspect radar and other sensors for proper mounting and unobstructed fields of view, especially after bumper removal. Also resolve steering angle or stability-control faults, which can prevent ADAS Calibration from starting even with perfect targets. If dynamic steps are required, confirm the vehicle is safe to drive and nearby roads have clear lane markings and steady-speed conditions. Doing this up front reduces rework and produces a defensible post-scan record.
What to Expect During On-Site Calibration: Target Alignment, Scan Tool Steps, and Road Procedure
During mobile ADAS Calibration for a Volkswagen T-Roc, the appointment follows a scan-guided sequence that controls both vehicle state and calibration order. We start by selecting the correct routine in the scan tool, confirming the module(s) involved, and placing the system into service mode so driver-assist features are ready for recalibration. For static steps, the Volkswagen T-Roc is positioned precisely, a centerline reference is established, and targets are placed using measured distances and heights. The scan tool prompts actions such as steering centering, brake holds, ignition cycles, and measurement confirmations while the module captures reference images/returns and computes offsets. Precision is what makes the calibration durable. Small errors in yaw, target height, or distance can later present as lane-centering bias, false alerts, or restricted adaptive cruise. If the procedure includes a dynamic phase, it follows only after the stationary step is accepted. Dynamic calibration is a controlled drive where the Volkswagen T-Roc must maintain specified speeds with clear lane markings until the tool indicates completion; congestion and poor markings can pause progress. Throughout the workflow, newly set DTCs are treated as diagnostic signals—obstruction, voltage instability, mounting issues, or unmet prerequisites—rather than something to clear and ignore. Once complete, a post-scan confirms clean module health, cleared warnings, and normal feature availability.
Proof and Documentation: Post-Scan Results, Verification, and Records for Volkswagen T-Roc
Proof and documentation close out mobile ADAS Calibration on a Volkswagen T-Roc, providing objective evidence that required routines were completed. A strong closeout includes a post-scan report showing which modules were checked, which DTCs existed before service, and whether any calibration-related faults remain afterward. It should also list the completed routines—forward camera calibration, radar aiming/verification, steering angle initialization, or sensor-fusion validation—so scope is clear. When possible, record the scan-tool routine name and completion status for the specific Volkswagen T-Roc configuration. These records matter beyond today’s visit. They establish a “known good” baseline that helps after later alignment work, suspension changes, another windshield replacement, or additional repairs that affect sensor geometry. They also support claims by showing ADAS Calibration was performed as a required step after glass or front-end work, not simply by clearing codes. Good documentation includes date/time, technician identification, method used (static, dynamic, or both), and brief notes on on-site prerequisites (level surface, tire pressures normalized, battery support used). If a dynamic drive was required, noting general completion conditions can explain why the routine passed. Finally, confirm warnings are off and features can be enabled; if completion isn’t possible, document the limiting factor and the next-step recommendation.
Enjoy More Relevant Blogs
ADAS Warning Lights on Volkswagen T-Roc: When Calibration Is the Fix and When It’s Not
ADAS warning lights on your Volkswagen T-Roc? Learn when calibration fixes lane assist or AEB issues, when it will not, and what to check next. Schedule help.
Camera Calibration for Volkswagen T-Roc: Lane Assist and Forward Collision Accuracy Explained
Need camera calibration for your Volkswagen T-Roc? See how calibration affects lane assist and forward collision accuracy after windshield service or repairs.
How to Schedule ADAS Calibration for Volkswagen T-Roc After Windshield Replacement
Schedule ADAS calibration for Volkswagen T-Roc after windshield replacement. Learn timing, required info, and what to expect so safety systems stay accurate.
Do You Need ADAS Calibration for Volkswagen T-Roc After a Wheel Alignment, Suspension Work, or a Minor Collision?
Do you need ADAS calibration for a Volkswagen T-Roc after alignment, suspension work, or a minor collision? Signs, timelines, safety risks, and costs today.
Pre- and Post-Calibration Scans for Volkswagen T-Roc: Proving Systems Are Set Correctly
Pre- and post-calibration scans for Volkswagen T-Roc: see why scans matter, what they verify, and how reports prove ADAS systems are set correctly after service.
ADAS Calibration Checklist for Volkswagen T-Roc: Documentation, Verification, and Final Safety Checks
ADAS calibration checklist for Volkswagen T-Roc: documentation to request, scans to verify, and safety checks that confirm cameras and sensors are set right.
How Much Does ADAS Calibration Cost for Volkswagen T-Roc? What Drives Pricing and What Insurance Typically Covers
How much does ADAS calibration cost for a Volkswagen T-Roc? Learn pricing drivers, camera vs radar needs, labor time, and what insurance typically covers.
Static vs Dynamic ADAS Calibration for Volkswagen T-Roc: What the Difference Means
Static vs dynamic ADAS calibration for Volkswagen T-Roc: key differences, when each is required, how long it takes, and what affects accuracy for safety.
OEM Calibration Requirements for Volkswagen T-Roc: How to Confirm What Must Be Calibrated
OEM calibration requirements for Volkswagen T-Roc: how to confirm what must be calibrated after repairs, what triggers recalibration, and what proof to ask for.
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm