Services
Service Areas
OEM-Quality Rear Glass Replacement for Chevrolet Express 1500 Passenger: Defroster Grid and Tint-Match Checklist
Verify the Correct Chevrolet Express 1500 Passenger Rear Glass: Privacy Shade, Defroster Grid, Antenna Lines, and DOT Markings
Getting OEM-quality rear glass for your Chevrolet Express 1500 Passenger starts with confirming what is built into the panel, not just the outline. Rear back glass can vary by trim, so we verify privacy shade (tinted-in-glass vs clear), the rear defroster grid, and any embedded antenna lines used for AM/FM, GPS, or keyless entry. We also confirm brackets, mounting pads, and cutouts tied to the hatch or liftgate so the glass fits and functions correctly. To keep the install looking factory, we match the frit band (black ceramic border) so the urethane adhesive footprint and UV protection are the same. We then check the etched compliance mark: U.S. glazing typically references FMVSS 205 and includes a DOT number that identifies the manufacturer or plant. Most rear panels are tempered and often marked AS-2 for rear/side use. Finally, we validate orientation and options such as wiper provisions (when equipped), third brake lamp visibility, and any openings for cameras or sensors. Bang AutoGlass verifies these details before installation so your Chevrolet Express 1500 Passenger rear window replacement is done right. Most jobs take 30-45 minutes, plus at least one hour of safe cure time. Every install is backed by a lifetime workmanship warranty, and we work with all insurance companies when comprehensive coverage applies.
Tint-Match Checklist for Chevrolet Express 1500 Passenger: Privacy Glass vs Film, VLT Expectations, and Color Tone
For a Chevrolet Express 1500 Passenger rear glass replacement, a true "tint match" starts by separating factory privacy glass from aftermarket tint film. Privacy glass is shaded in the glass itself; film is applied later to the inside surface. If your Chevrolet Express 1500 Passenger came with privacy glass, the most OEM-looking fix is installing OEM-quality privacy rear glass with the expected DOT/AS markings and built-in shade. From there we check VLT, net VLT, and color tone. Visible Light Transmission (VLT) is the percentage of light that passes through one layer. Many SUVs and trucks with privacy glass land around 15-26% VLT, while clear automotive glass is often closer to 70-85% VLT, so a clear replacement can stand out immediately. If the old back window also had film, the final look is net VLT (glass plus film), which is why re-tinting after rear window replacement is common to achieve a seamless match. Tone matters too: privacy glass may read neutral gray/charcoal, or lean green or bronze, and it should match the other rear panels. Tint rules vary by state, so we focus on duplicating what your Chevrolet Express 1500 Passenger had. Bang AutoGlass is mobile and often available next day, and every rear glass replacement is backed by a lifetime workmanship warranty.
Rear Defroster Grid Basics: Lines, Power Tabs, and What Common Failures Look Like
The rear defroster grid on your Chevrolet Express 1500 Passenger is an electrical heater that clears fog and light frost quickly. The thin horizontal lines on the inside of the rear glass are conductive traces supplied through two vertical bus bars. When activated, the system typically sends about 12-14 volts through bonded power and ground tabs and a short harness connector. If a tab is loose, corroded, or detached, the defroster may fail even when the printed lines look fine. The pattern of clearing helps diagnose the issue. If you see narrow bands that never clear, you likely have broken grid lines, commonly from scraping ice, decals, or abrasive cleaning. If the indicator light is on but the entire window stays fogged, the cause may be a blown fuse, bad relay, switch/control issue, poor ground, or a module fault. During an OEM-quality rear glass replacement for your Chevrolet Express 1500 Passenger, we verify the correct grid layout and tab locations, then ensure the connector seats cleanly without stressing the terminals. Bang AutoGlass is a mobile service in {city}, {state}, often available next day, and our workmanship is covered by a lifetime warranty, so your rear window replacement restores function, not just glass.
Install Prep That Protects Fit: Interior Protection, Pinchweld Checks, and Bond Surface Readiness
For a Chevrolet Express 1500 Passenger rear window replacement to look and perform like OEM, the installation wins in the prep. We protect the cabin and cargo area, remove required trim and moldings without damaging retainers, and clean up fine fragments so debris doesn't rattle under panels. With the opening clear, we inspect the pinchweld/bonding flange for corrosion, paint chips, urethane contamination, or evidence of a prior subpar rear glass replacement. We trim old urethane to a thin, consistent bed (roughly 1–2 mm) so new adhesive bonds to a compatible base while limiting bare metal. If rust or exposed steel is present, we treat it and apply the correct primer for the adhesive system, because surface chemistry drives bond strength and water tightness. We then dry-fit OEM-quality rear glass to confirm indexing, molding fit, and frit alignment, prep both surfaces with approved cleaner/primer, apply an even urethane bead, and set the glass with controlled pressure to avoid leaks and wind noise. Bang AutoGlass delivers this method as a mobile service across {city}, {state}, often next day. Most installs take 30–45 minutes plus at least one hour of safe cure time, and every job is backed by our lifetime workmanship warranty.
Defroster Reconnect and Testing: Tabs, Harness Connection, and Function Verification on Chevrolet Express 1500 Passenger
After a Chevrolet Express 1500 Passenger rear glass replacement, restoring rear defroster performance is critical. The heating grid is printed on the inside of the glass and connects through two bonded tabs (power and ground) and a small harness connector. We confirm the correct grid layout and tab positions for your Chevrolet Express 1500 Passenger, then reconnect the harness with a straight, controlled push—no twisting, yanking, or prying—so the tabs aren't stressed. We also check that the connector is clean and fully seated; a loose fit can cause intermittent heat or a complete no-heat condition. Before we leave, we do a practical function check: with the vehicle on and the defroster switched on, you should see proper power at the terminals (typically near battery voltage) and the grid should begin warming within about a minute as conditions allow. If it doesn't respond, common causes include a blown fuse, relay/switch issues, poor ground, or damaged grid lines from scraping, decals, or abrasive cleaning. Clean the inside glass gently to protect the traces. Bang AutoGlass is mobile, often available next day, backed by a lifetime workmanship warranty, and we accept all insurance companies when comprehensive coverage applies.
Aftercare and Final QC: Safe Drive-Away Timing, Leak/Wind Noise Checks, and Defroster Use
Aftercare and final QC separate a routine rear glass replacement from an OEM-quality result on your Chevrolet Express 1500 Passenger. Before we pack up, we confirm the glass is seated evenly and that moldings, garnish trim, and retainers are flush. We inspect the urethane bond line for continuity around the opening, because small voids can later become leaks, a damp headliner, or a whistle at highway speed. Where conditions allow, we do a quick leak-risk/wind-noise check and confirm the rear defroster connector is secure and responding normally. Most rear glass replacements take 30–45 minutes, and we recommend at least one hour of safe drive-away time so the adhesive can set. Because cure continues and temperature and humidity in {city}, {state} can influence results, treat the first day as low-stress. Avoid automatic or high-pressure car washes for at least 48 hours and minimize door slams and rough-road impacts. If retention tape is used, leave it in place as directed. Quick defroster checks are fine, but avoid extended cycles for about 24 hours. If you notice water intrusion, wind noise, or shifting trim, contact Bang AutoGlass—covered by our lifetime workmanship warranty, and we work with all insurance companies when comprehensive coverage applies.
Services
Service Areas
OEM-Quality Rear Glass Replacement for Chevrolet Express 1500 Passenger: Defroster Grid and Tint-Match Checklist
Verify the Correct Chevrolet Express 1500 Passenger Rear Glass: Privacy Shade, Defroster Grid, Antenna Lines, and DOT Markings
Getting OEM-quality rear glass for your Chevrolet Express 1500 Passenger starts with confirming what is built into the panel, not just the outline. Rear back glass can vary by trim, so we verify privacy shade (tinted-in-glass vs clear), the rear defroster grid, and any embedded antenna lines used for AM/FM, GPS, or keyless entry. We also confirm brackets, mounting pads, and cutouts tied to the hatch or liftgate so the glass fits and functions correctly. To keep the install looking factory, we match the frit band (black ceramic border) so the urethane adhesive footprint and UV protection are the same. We then check the etched compliance mark: U.S. glazing typically references FMVSS 205 and includes a DOT number that identifies the manufacturer or plant. Most rear panels are tempered and often marked AS-2 for rear/side use. Finally, we validate orientation and options such as wiper provisions (when equipped), third brake lamp visibility, and any openings for cameras or sensors. Bang AutoGlass verifies these details before installation so your Chevrolet Express 1500 Passenger rear window replacement is done right. Most jobs take 30-45 minutes, plus at least one hour of safe cure time. Every install is backed by a lifetime workmanship warranty, and we work with all insurance companies when comprehensive coverage applies.
Tint-Match Checklist for Chevrolet Express 1500 Passenger: Privacy Glass vs Film, VLT Expectations, and Color Tone
For a Chevrolet Express 1500 Passenger rear glass replacement, a true "tint match" starts by separating factory privacy glass from aftermarket tint film. Privacy glass is shaded in the glass itself; film is applied later to the inside surface. If your Chevrolet Express 1500 Passenger came with privacy glass, the most OEM-looking fix is installing OEM-quality privacy rear glass with the expected DOT/AS markings and built-in shade. From there we check VLT, net VLT, and color tone. Visible Light Transmission (VLT) is the percentage of light that passes through one layer. Many SUVs and trucks with privacy glass land around 15-26% VLT, while clear automotive glass is often closer to 70-85% VLT, so a clear replacement can stand out immediately. If the old back window also had film, the final look is net VLT (glass plus film), which is why re-tinting after rear window replacement is common to achieve a seamless match. Tone matters too: privacy glass may read neutral gray/charcoal, or lean green or bronze, and it should match the other rear panels. Tint rules vary by state, so we focus on duplicating what your Chevrolet Express 1500 Passenger had. Bang AutoGlass is mobile and often available next day, and every rear glass replacement is backed by a lifetime workmanship warranty.
Rear Defroster Grid Basics: Lines, Power Tabs, and What Common Failures Look Like
The rear defroster grid on your Chevrolet Express 1500 Passenger is an electrical heater that clears fog and light frost quickly. The thin horizontal lines on the inside of the rear glass are conductive traces supplied through two vertical bus bars. When activated, the system typically sends about 12-14 volts through bonded power and ground tabs and a short harness connector. If a tab is loose, corroded, or detached, the defroster may fail even when the printed lines look fine. The pattern of clearing helps diagnose the issue. If you see narrow bands that never clear, you likely have broken grid lines, commonly from scraping ice, decals, or abrasive cleaning. If the indicator light is on but the entire window stays fogged, the cause may be a blown fuse, bad relay, switch/control issue, poor ground, or a module fault. During an OEM-quality rear glass replacement for your Chevrolet Express 1500 Passenger, we verify the correct grid layout and tab locations, then ensure the connector seats cleanly without stressing the terminals. Bang AutoGlass is a mobile service in {city}, {state}, often available next day, and our workmanship is covered by a lifetime warranty, so your rear window replacement restores function, not just glass.
Install Prep That Protects Fit: Interior Protection, Pinchweld Checks, and Bond Surface Readiness
For a Chevrolet Express 1500 Passenger rear window replacement to look and perform like OEM, the installation wins in the prep. We protect the cabin and cargo area, remove required trim and moldings without damaging retainers, and clean up fine fragments so debris doesn't rattle under panels. With the opening clear, we inspect the pinchweld/bonding flange for corrosion, paint chips, urethane contamination, or evidence of a prior subpar rear glass replacement. We trim old urethane to a thin, consistent bed (roughly 1–2 mm) so new adhesive bonds to a compatible base while limiting bare metal. If rust or exposed steel is present, we treat it and apply the correct primer for the adhesive system, because surface chemistry drives bond strength and water tightness. We then dry-fit OEM-quality rear glass to confirm indexing, molding fit, and frit alignment, prep both surfaces with approved cleaner/primer, apply an even urethane bead, and set the glass with controlled pressure to avoid leaks and wind noise. Bang AutoGlass delivers this method as a mobile service across {city}, {state}, often next day. Most installs take 30–45 minutes plus at least one hour of safe cure time, and every job is backed by our lifetime workmanship warranty.
Defroster Reconnect and Testing: Tabs, Harness Connection, and Function Verification on Chevrolet Express 1500 Passenger
After a Chevrolet Express 1500 Passenger rear glass replacement, restoring rear defroster performance is critical. The heating grid is printed on the inside of the glass and connects through two bonded tabs (power and ground) and a small harness connector. We confirm the correct grid layout and tab positions for your Chevrolet Express 1500 Passenger, then reconnect the harness with a straight, controlled push—no twisting, yanking, or prying—so the tabs aren't stressed. We also check that the connector is clean and fully seated; a loose fit can cause intermittent heat or a complete no-heat condition. Before we leave, we do a practical function check: with the vehicle on and the defroster switched on, you should see proper power at the terminals (typically near battery voltage) and the grid should begin warming within about a minute as conditions allow. If it doesn't respond, common causes include a blown fuse, relay/switch issues, poor ground, or damaged grid lines from scraping, decals, or abrasive cleaning. Clean the inside glass gently to protect the traces. Bang AutoGlass is mobile, often available next day, backed by a lifetime workmanship warranty, and we accept all insurance companies when comprehensive coverage applies.
Aftercare and Final QC: Safe Drive-Away Timing, Leak/Wind Noise Checks, and Defroster Use
Aftercare and final QC separate a routine rear glass replacement from an OEM-quality result on your Chevrolet Express 1500 Passenger. Before we pack up, we confirm the glass is seated evenly and that moldings, garnish trim, and retainers are flush. We inspect the urethane bond line for continuity around the opening, because small voids can later become leaks, a damp headliner, or a whistle at highway speed. Where conditions allow, we do a quick leak-risk/wind-noise check and confirm the rear defroster connector is secure and responding normally. Most rear glass replacements take 30–45 minutes, and we recommend at least one hour of safe drive-away time so the adhesive can set. Because cure continues and temperature and humidity in {city}, {state} can influence results, treat the first day as low-stress. Avoid automatic or high-pressure car washes for at least 48 hours and minimize door slams and rough-road impacts. If retention tape is used, leave it in place as directed. Quick defroster checks are fine, but avoid extended cycles for about 24 hours. If you notice water intrusion, wind noise, or shifting trim, contact Bang AutoGlass—covered by our lifetime workmanship warranty, and we work with all insurance companies when comprehensive coverage applies.
Services
Service Areas
OEM-Quality Rear Glass Replacement for Chevrolet Express 1500 Passenger: Defroster Grid and Tint-Match Checklist
Verify the Correct Chevrolet Express 1500 Passenger Rear Glass: Privacy Shade, Defroster Grid, Antenna Lines, and DOT Markings
Getting OEM-quality rear glass for your Chevrolet Express 1500 Passenger starts with confirming what is built into the panel, not just the outline. Rear back glass can vary by trim, so we verify privacy shade (tinted-in-glass vs clear), the rear defroster grid, and any embedded antenna lines used for AM/FM, GPS, or keyless entry. We also confirm brackets, mounting pads, and cutouts tied to the hatch or liftgate so the glass fits and functions correctly. To keep the install looking factory, we match the frit band (black ceramic border) so the urethane adhesive footprint and UV protection are the same. We then check the etched compliance mark: U.S. glazing typically references FMVSS 205 and includes a DOT number that identifies the manufacturer or plant. Most rear panels are tempered and often marked AS-2 for rear/side use. Finally, we validate orientation and options such as wiper provisions (when equipped), third brake lamp visibility, and any openings for cameras or sensors. Bang AutoGlass verifies these details before installation so your Chevrolet Express 1500 Passenger rear window replacement is done right. Most jobs take 30-45 minutes, plus at least one hour of safe cure time. Every install is backed by a lifetime workmanship warranty, and we work with all insurance companies when comprehensive coverage applies.
Tint-Match Checklist for Chevrolet Express 1500 Passenger: Privacy Glass vs Film, VLT Expectations, and Color Tone
For a Chevrolet Express 1500 Passenger rear glass replacement, a true "tint match" starts by separating factory privacy glass from aftermarket tint film. Privacy glass is shaded in the glass itself; film is applied later to the inside surface. If your Chevrolet Express 1500 Passenger came with privacy glass, the most OEM-looking fix is installing OEM-quality privacy rear glass with the expected DOT/AS markings and built-in shade. From there we check VLT, net VLT, and color tone. Visible Light Transmission (VLT) is the percentage of light that passes through one layer. Many SUVs and trucks with privacy glass land around 15-26% VLT, while clear automotive glass is often closer to 70-85% VLT, so a clear replacement can stand out immediately. If the old back window also had film, the final look is net VLT (glass plus film), which is why re-tinting after rear window replacement is common to achieve a seamless match. Tone matters too: privacy glass may read neutral gray/charcoal, or lean green or bronze, and it should match the other rear panels. Tint rules vary by state, so we focus on duplicating what your Chevrolet Express 1500 Passenger had. Bang AutoGlass is mobile and often available next day, and every rear glass replacement is backed by a lifetime workmanship warranty.
Rear Defroster Grid Basics: Lines, Power Tabs, and What Common Failures Look Like
The rear defroster grid on your Chevrolet Express 1500 Passenger is an electrical heater that clears fog and light frost quickly. The thin horizontal lines on the inside of the rear glass are conductive traces supplied through two vertical bus bars. When activated, the system typically sends about 12-14 volts through bonded power and ground tabs and a short harness connector. If a tab is loose, corroded, or detached, the defroster may fail even when the printed lines look fine. The pattern of clearing helps diagnose the issue. If you see narrow bands that never clear, you likely have broken grid lines, commonly from scraping ice, decals, or abrasive cleaning. If the indicator light is on but the entire window stays fogged, the cause may be a blown fuse, bad relay, switch/control issue, poor ground, or a module fault. During an OEM-quality rear glass replacement for your Chevrolet Express 1500 Passenger, we verify the correct grid layout and tab locations, then ensure the connector seats cleanly without stressing the terminals. Bang AutoGlass is a mobile service in {city}, {state}, often available next day, and our workmanship is covered by a lifetime warranty, so your rear window replacement restores function, not just glass.
Install Prep That Protects Fit: Interior Protection, Pinchweld Checks, and Bond Surface Readiness
For a Chevrolet Express 1500 Passenger rear window replacement to look and perform like OEM, the installation wins in the prep. We protect the cabin and cargo area, remove required trim and moldings without damaging retainers, and clean up fine fragments so debris doesn't rattle under panels. With the opening clear, we inspect the pinchweld/bonding flange for corrosion, paint chips, urethane contamination, or evidence of a prior subpar rear glass replacement. We trim old urethane to a thin, consistent bed (roughly 1–2 mm) so new adhesive bonds to a compatible base while limiting bare metal. If rust or exposed steel is present, we treat it and apply the correct primer for the adhesive system, because surface chemistry drives bond strength and water tightness. We then dry-fit OEM-quality rear glass to confirm indexing, molding fit, and frit alignment, prep both surfaces with approved cleaner/primer, apply an even urethane bead, and set the glass with controlled pressure to avoid leaks and wind noise. Bang AutoGlass delivers this method as a mobile service across {city}, {state}, often next day. Most installs take 30–45 minutes plus at least one hour of safe cure time, and every job is backed by our lifetime workmanship warranty.
Defroster Reconnect and Testing: Tabs, Harness Connection, and Function Verification on Chevrolet Express 1500 Passenger
After a Chevrolet Express 1500 Passenger rear glass replacement, restoring rear defroster performance is critical. The heating grid is printed on the inside of the glass and connects through two bonded tabs (power and ground) and a small harness connector. We confirm the correct grid layout and tab positions for your Chevrolet Express 1500 Passenger, then reconnect the harness with a straight, controlled push—no twisting, yanking, or prying—so the tabs aren't stressed. We also check that the connector is clean and fully seated; a loose fit can cause intermittent heat or a complete no-heat condition. Before we leave, we do a practical function check: with the vehicle on and the defroster switched on, you should see proper power at the terminals (typically near battery voltage) and the grid should begin warming within about a minute as conditions allow. If it doesn't respond, common causes include a blown fuse, relay/switch issues, poor ground, or damaged grid lines from scraping, decals, or abrasive cleaning. Clean the inside glass gently to protect the traces. Bang AutoGlass is mobile, often available next day, backed by a lifetime workmanship warranty, and we accept all insurance companies when comprehensive coverage applies.
Aftercare and Final QC: Safe Drive-Away Timing, Leak/Wind Noise Checks, and Defroster Use
Aftercare and final QC separate a routine rear glass replacement from an OEM-quality result on your Chevrolet Express 1500 Passenger. Before we pack up, we confirm the glass is seated evenly and that moldings, garnish trim, and retainers are flush. We inspect the urethane bond line for continuity around the opening, because small voids can later become leaks, a damp headliner, or a whistle at highway speed. Where conditions allow, we do a quick leak-risk/wind-noise check and confirm the rear defroster connector is secure and responding normally. Most rear glass replacements take 30–45 minutes, and we recommend at least one hour of safe drive-away time so the adhesive can set. Because cure continues and temperature and humidity in {city}, {state} can influence results, treat the first day as low-stress. Avoid automatic or high-pressure car washes for at least 48 hours and minimize door slams and rough-road impacts. If retention tape is used, leave it in place as directed. Quick defroster checks are fine, but avoid extended cycles for about 24 hours. If you notice water intrusion, wind noise, or shifting trim, contact Bang AutoGlass—covered by our lifetime workmanship warranty, and we work with all insurance companies when comprehensive coverage applies.
Enjoy More Relevant Blogs
How Long Does Rear Glass Replacement Take on Chevrolet Express 1500 Passenger? Install Time, Adhesive Cure Time, and When It’s Safe to Drive
How long is Chevrolet Express 1500 Passenger rear glass replacement? Get install time, urethane cure guidelines, and drive-away timing after service. Plan your visit today.
Shattered Back Window on Chevrolet Express 1500 Passenger: A Step-by-Step Rear Glass Replacement Plan
Shattered back window on Chevrolet Express 1500 Passenger? Follow a step-by-step rear glass replacement plan, cleanup tips, defroster notes, cure time, and drive-away rules.
How to Schedule Mobile Rear Glass Replacement for Chevrolet Express 1500 Passenger
Schedule mobile rear glass replacement for your Chevrolet Express 1500 Passenger in minutes. Learn what info to provide, how long it takes, and prep tips for service day.
Post-Install Checks for Chevrolet Express 1500 Passenger: Rear Glass Replacement Wind Noise, Leaks, and Rattle Tests
Post-install rear glass checks for Chevrolet Express 1500 Passenger: test for wind noise, leaks, and rattles, plus when to return for warranty service—check today before trips.
How Much Does Rear Glass Replacement Cost for Chevrolet Express 1500 Passenger? Pricing Factors, OEM vs Aftermarket, and Insurance Deductibles
Estimate Chevrolet Express 1500 Passenger rear glass replacement cost. Compare OEM vs aftermarket, labor factors, insurance deductibles, and ways to save. Request a quote.
Tempered Safety Rear Glass Replacement for Chevrolet Express 1500 Passenger: Understanding DOT Markings and FMVSS 205
Need Chevrolet Express 1500 Passenger rear glass replacement? Learn tempered safety glass basics, DOT markings, and FMVSS 205, plus install and cure tips. Get a quote today.
Back Glass Replacement on Chevrolet Express 1500 Passenger: Defroster Tabs, Antenna Lines, and Connector Reattachment Basics
Back glass replacement on Chevrolet Express 1500 Passenger: defroster tabs, antenna lines, and connectors explained, plus install tips to avoid damage and rework safely.
Rear Glass Replacement for Chevrolet Express 1500 Passenger: What to Expect During Install and Aftercare
Rear glass replacement for Chevrolet Express 1500 Passenger: what happens during install, defroster and tint considerations, cure time, and aftercare to prevent leaks long-term.
Rear Defroster Not Working on Chevrolet Express 1500 Passenger? When Rear Glass Replacement Makes More Sense Than Repair
Rear defroster not working on your Chevrolet Express 1500 Passenger? Learn common causes, when repair fails, and when rear glass replacement is the smarter fix for winter.
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm