Services
Service Areas
OEM-Quality Rear Glass Replacement for Bmw 2 Series Gran Tourer: Defroster Grid and Tint-Match Checklist
Verify the Correct Bmw 2 Series Gran Tourer Rear Glass: Privacy Shade, Defroster Grid, Antenna Lines, and DOT Markings
Choosing OEM-quality rear glass for your Bmw 2 Series Gran Tourer is about matching features as much as matching the opening. We confirm whether your vehicle uses privacy shade (tinted-in-glass), a rear defroster grid, and any embedded antenna lines for radio, GPS, or keyless entry. We also check the hatch or liftgate for brackets, mounting pads, and cutouts that must be present for a factory-style fit. To keep the install looking OEM, we match the frit band (black ceramic border) so the urethane bonding area and UV shielding are correct. Next we verify the glass etching: U.S. automotive glazing typically references FMVSS 205 and includes a DOT number that identifies the manufacturer or plant. Most rear panels are tempered and often marked AS-2 for rear/side use. We then confirm orientation and options such as third brake lamp visibility, wiper provisions (when equipped), and any openings for cameras or sensors. Bang AutoGlass performs this verification before we arrive in {city}, {state} so your Bmw 2 Series Gran Tourer rear window replacement is done right. Most jobs take 30-45 minutes, plus at least one hour of safe cure time. Every install is backed by a lifetime workmanship warranty, and we work with all insurance companies when comprehensive coverage applies.
Tint-Match Checklist for Bmw 2 Series Gran Tourer: Privacy Glass vs Film, VLT Expectations, and Color Tone
When you request a "tint match" for a Bmw 2 Series Gran Tourer rear glass replacement, we first confirm whether you are matching factory privacy glass or added tint film. Privacy glass is dyed in the glass; film is applied to the inside surface later. If your Bmw 2 Series Gran Tourer originally had privacy glass, the most OEM result is installing OEM-quality privacy rear glass with the correct DOT/AS markings and built-in shade. Then we evaluate VLT, net VLT, and tone. VLT (Visible Light Transmission) measures how much light passes through a single layer. Factory privacy glass on many SUVs and trucks is often around 15-26% VLT, while clear glass may be closer to 70-85% VLT, so a clear replacement can look obviously different. If the prior rear window also had film, the final shade is net VLT (glass plus film), so plan to re-tint after replacement for a true match. Tone is the next giveaway: some privacy glass leans charcoal/gray, others show a green or bronze cast, and it should track your other rear panels. Because tint rules vary by {state}, we focus on duplicating what you had. Bang AutoGlass is mobile in {city}, {state}, often available next day, and every rear window replacement is backed by a lifetime workmanship warranty.
Rear Defroster Grid Basics: Lines, Power Tabs, and What Common Failures Look Like
The rear defroster grid on your Bmw 2 Series Gran Tourer is a simple heater circuit that restores visibility in rain, humidity, and winter weather. The thin horizontal lines on the inside of the rear glass are conductive traces, fed by two vertical bus bars. When you press the defrost button, the system typically applies about 12-14 volts through bonded power and ground tabs on the glass, warming the surface to clear fog and light frost. Because the connection is made at those tabs, a loose connector, corrosion, or a detached tab can stop the entire grid even if the lines look intact. If only part of the window clears, that usually points to broken grid lines, often caused by scraping ice, removing stickers, or using abrasive cleaners. If the indicator light is on but nothing clears anywhere, common upstream causes include a blown fuse, bad relay, switch issue, control module fault, or poor ground. During an OEM-quality rear glass replacement on your Bmw 2 Series Gran Tourer, we verify the correct grid pattern, tab placement, and connector fit so the defroster works after the rear window replacement. Bang AutoGlass is mobile, often available next day, and our installs are backed by a lifetime workmanship warranty.
Install Prep That Protects Fit: Interior Protection, Pinchweld Checks, and Bond Surface Readiness
Rear glass replacement quality on a Bmw 2 Series Gran Tourer is determined before the new panel is ever set. Bang AutoGlass starts by protecting the interior—seats, headliner, trim, and cargo area—then removing necessary moldings and liftgate panels and vacuuming thoroughly to keep debris out of latches and interior panels. Next we inspect the pinchweld/bonding flange for rust, paint damage, and signs of prior substandard repairs that can compromise urethane adhesion. Standard stationary-glass practice is to trim existing urethane to a thin, uniform layer (about 1–2 mm) so fresh urethane bonds reliably to a stable base while minimizing exposed metal. If bare metal or corrosion is present, we address it with proper surface prep and the correct primer for the adhesive system. We then dry-fit OEM-quality rear glass to confirm alignment, molding fit, and consistent gaps, prep the glass frit and vehicle bonding surface with approved cleaner/primer, and lay a consistent urethane bead before setting the glass square to avoid leaks and whistles. We're mobile in {city}, {state}, often next day. Most installs take 30–45 minutes plus at least one hour of safe cure time. Every job includes a lifetime workmanship warranty, and we work with all insurance companies when comprehensive coverage applies.
Defroster Reconnect and Testing: Tabs, Harness Connection, and Function Verification on Bmw 2 Series Gran Tourer
Defroster reconnection is a critical step after a Bmw 2 Series Gran Tourer rear glass replacement because the system depends on solid electrical contact at the glass terminals. The heating grid is printed on the inside surface and connects through two bonded tabs—power and ground—plus a short harness connector. After installation, we confirm the harness reaches naturally and tab placement matches the factory layout for your Bmw 2 Series Gran Tourer. If the harness is forced, tabs can loosen later, so we reconnect with controlled, straight pressure rather than twisting or levering. We also verify the connector is clean and fully seated; partial seating can cause intermittent heating or a no-heat condition even when the grid looks perfect. Functional testing is simple: with ignition on and the defroster switched on, you should typically see near battery voltage at the terminals and feel the grid begin warming within about a minute. If nothing changes, start with fuse/relay and then switch/control and ground integrity. If only some areas clear, the usual culprit is broken grid lines from scraping ice, decal removal, or abrasive cleaning. Use non-abrasive products to protect the traces. Bang AutoGlass is mobile across {city}, {state}, often next day, and every install includes a lifetime workmanship warranty.
Aftercare and Final QC: Safe Drive-Away Timing, Leak/Wind Noise Checks, and Defroster Use
We close out every Bmw 2 Series Gran Tourer rear window replacement with final QC and clear aftercare, because the first 24–48 hours influence long-term sealing. On-site, we confirm the glass sits square, the reveal is even, and moldings and interior garnish trim are flush. We inspect the urethane line for continuity around the perimeter, since small voids can later translate into water entry or wind noise. We also verify the rear defroster connection is secure and the grid responds when commanded on. Most rear glass replacements take 30–45 minutes, followed by at least one hour of safe drive-away time for the urethane to set. Because cure continues after you leave and weather in {city}, {state} can affect it, keep stress low the first day: avoid slamming doors, rough-road impacts, and cabin-pressure changes. Skip automatic or high-pressure car washes for at least 48 hours and don't aim water jets at the perimeter. If retention tape is applied, keep it on as directed. Defroster testing is fine, but avoid long cycles for about 24 hours. If you notice leaks, whistling, or trim movement, Bang AutoGlass will address it under our lifetime workmanship warranty, and we work with all insurance companies when comprehensive coverage applies.
Services
Service Areas
OEM-Quality Rear Glass Replacement for Bmw 2 Series Gran Tourer: Defroster Grid and Tint-Match Checklist
Verify the Correct Bmw 2 Series Gran Tourer Rear Glass: Privacy Shade, Defroster Grid, Antenna Lines, and DOT Markings
Choosing OEM-quality rear glass for your Bmw 2 Series Gran Tourer is about matching features as much as matching the opening. We confirm whether your vehicle uses privacy shade (tinted-in-glass), a rear defroster grid, and any embedded antenna lines for radio, GPS, or keyless entry. We also check the hatch or liftgate for brackets, mounting pads, and cutouts that must be present for a factory-style fit. To keep the install looking OEM, we match the frit band (black ceramic border) so the urethane bonding area and UV shielding are correct. Next we verify the glass etching: U.S. automotive glazing typically references FMVSS 205 and includes a DOT number that identifies the manufacturer or plant. Most rear panels are tempered and often marked AS-2 for rear/side use. We then confirm orientation and options such as third brake lamp visibility, wiper provisions (when equipped), and any openings for cameras or sensors. Bang AutoGlass performs this verification before we arrive in {city}, {state} so your Bmw 2 Series Gran Tourer rear window replacement is done right. Most jobs take 30-45 minutes, plus at least one hour of safe cure time. Every install is backed by a lifetime workmanship warranty, and we work with all insurance companies when comprehensive coverage applies.
Tint-Match Checklist for Bmw 2 Series Gran Tourer: Privacy Glass vs Film, VLT Expectations, and Color Tone
When you request a "tint match" for a Bmw 2 Series Gran Tourer rear glass replacement, we first confirm whether you are matching factory privacy glass or added tint film. Privacy glass is dyed in the glass; film is applied to the inside surface later. If your Bmw 2 Series Gran Tourer originally had privacy glass, the most OEM result is installing OEM-quality privacy rear glass with the correct DOT/AS markings and built-in shade. Then we evaluate VLT, net VLT, and tone. VLT (Visible Light Transmission) measures how much light passes through a single layer. Factory privacy glass on many SUVs and trucks is often around 15-26% VLT, while clear glass may be closer to 70-85% VLT, so a clear replacement can look obviously different. If the prior rear window also had film, the final shade is net VLT (glass plus film), so plan to re-tint after replacement for a true match. Tone is the next giveaway: some privacy glass leans charcoal/gray, others show a green or bronze cast, and it should track your other rear panels. Because tint rules vary by {state}, we focus on duplicating what you had. Bang AutoGlass is mobile in {city}, {state}, often available next day, and every rear window replacement is backed by a lifetime workmanship warranty.
Rear Defroster Grid Basics: Lines, Power Tabs, and What Common Failures Look Like
The rear defroster grid on your Bmw 2 Series Gran Tourer is a simple heater circuit that restores visibility in rain, humidity, and winter weather. The thin horizontal lines on the inside of the rear glass are conductive traces, fed by two vertical bus bars. When you press the defrost button, the system typically applies about 12-14 volts through bonded power and ground tabs on the glass, warming the surface to clear fog and light frost. Because the connection is made at those tabs, a loose connector, corrosion, or a detached tab can stop the entire grid even if the lines look intact. If only part of the window clears, that usually points to broken grid lines, often caused by scraping ice, removing stickers, or using abrasive cleaners. If the indicator light is on but nothing clears anywhere, common upstream causes include a blown fuse, bad relay, switch issue, control module fault, or poor ground. During an OEM-quality rear glass replacement on your Bmw 2 Series Gran Tourer, we verify the correct grid pattern, tab placement, and connector fit so the defroster works after the rear window replacement. Bang AutoGlass is mobile, often available next day, and our installs are backed by a lifetime workmanship warranty.
Install Prep That Protects Fit: Interior Protection, Pinchweld Checks, and Bond Surface Readiness
Rear glass replacement quality on a Bmw 2 Series Gran Tourer is determined before the new panel is ever set. Bang AutoGlass starts by protecting the interior—seats, headliner, trim, and cargo area—then removing necessary moldings and liftgate panels and vacuuming thoroughly to keep debris out of latches and interior panels. Next we inspect the pinchweld/bonding flange for rust, paint damage, and signs of prior substandard repairs that can compromise urethane adhesion. Standard stationary-glass practice is to trim existing urethane to a thin, uniform layer (about 1–2 mm) so fresh urethane bonds reliably to a stable base while minimizing exposed metal. If bare metal or corrosion is present, we address it with proper surface prep and the correct primer for the adhesive system. We then dry-fit OEM-quality rear glass to confirm alignment, molding fit, and consistent gaps, prep the glass frit and vehicle bonding surface with approved cleaner/primer, and lay a consistent urethane bead before setting the glass square to avoid leaks and whistles. We're mobile in {city}, {state}, often next day. Most installs take 30–45 minutes plus at least one hour of safe cure time. Every job includes a lifetime workmanship warranty, and we work with all insurance companies when comprehensive coverage applies.
Defroster Reconnect and Testing: Tabs, Harness Connection, and Function Verification on Bmw 2 Series Gran Tourer
Defroster reconnection is a critical step after a Bmw 2 Series Gran Tourer rear glass replacement because the system depends on solid electrical contact at the glass terminals. The heating grid is printed on the inside surface and connects through two bonded tabs—power and ground—plus a short harness connector. After installation, we confirm the harness reaches naturally and tab placement matches the factory layout for your Bmw 2 Series Gran Tourer. If the harness is forced, tabs can loosen later, so we reconnect with controlled, straight pressure rather than twisting or levering. We also verify the connector is clean and fully seated; partial seating can cause intermittent heating or a no-heat condition even when the grid looks perfect. Functional testing is simple: with ignition on and the defroster switched on, you should typically see near battery voltage at the terminals and feel the grid begin warming within about a minute. If nothing changes, start with fuse/relay and then switch/control and ground integrity. If only some areas clear, the usual culprit is broken grid lines from scraping ice, decal removal, or abrasive cleaning. Use non-abrasive products to protect the traces. Bang AutoGlass is mobile across {city}, {state}, often next day, and every install includes a lifetime workmanship warranty.
Aftercare and Final QC: Safe Drive-Away Timing, Leak/Wind Noise Checks, and Defroster Use
We close out every Bmw 2 Series Gran Tourer rear window replacement with final QC and clear aftercare, because the first 24–48 hours influence long-term sealing. On-site, we confirm the glass sits square, the reveal is even, and moldings and interior garnish trim are flush. We inspect the urethane line for continuity around the perimeter, since small voids can later translate into water entry or wind noise. We also verify the rear defroster connection is secure and the grid responds when commanded on. Most rear glass replacements take 30–45 minutes, followed by at least one hour of safe drive-away time for the urethane to set. Because cure continues after you leave and weather in {city}, {state} can affect it, keep stress low the first day: avoid slamming doors, rough-road impacts, and cabin-pressure changes. Skip automatic or high-pressure car washes for at least 48 hours and don't aim water jets at the perimeter. If retention tape is applied, keep it on as directed. Defroster testing is fine, but avoid long cycles for about 24 hours. If you notice leaks, whistling, or trim movement, Bang AutoGlass will address it under our lifetime workmanship warranty, and we work with all insurance companies when comprehensive coverage applies.
Services
Service Areas
OEM-Quality Rear Glass Replacement for Bmw 2 Series Gran Tourer: Defroster Grid and Tint-Match Checklist
Verify the Correct Bmw 2 Series Gran Tourer Rear Glass: Privacy Shade, Defroster Grid, Antenna Lines, and DOT Markings
Choosing OEM-quality rear glass for your Bmw 2 Series Gran Tourer is about matching features as much as matching the opening. We confirm whether your vehicle uses privacy shade (tinted-in-glass), a rear defroster grid, and any embedded antenna lines for radio, GPS, or keyless entry. We also check the hatch or liftgate for brackets, mounting pads, and cutouts that must be present for a factory-style fit. To keep the install looking OEM, we match the frit band (black ceramic border) so the urethane bonding area and UV shielding are correct. Next we verify the glass etching: U.S. automotive glazing typically references FMVSS 205 and includes a DOT number that identifies the manufacturer or plant. Most rear panels are tempered and often marked AS-2 for rear/side use. We then confirm orientation and options such as third brake lamp visibility, wiper provisions (when equipped), and any openings for cameras or sensors. Bang AutoGlass performs this verification before we arrive in {city}, {state} so your Bmw 2 Series Gran Tourer rear window replacement is done right. Most jobs take 30-45 minutes, plus at least one hour of safe cure time. Every install is backed by a lifetime workmanship warranty, and we work with all insurance companies when comprehensive coverage applies.
Tint-Match Checklist for Bmw 2 Series Gran Tourer: Privacy Glass vs Film, VLT Expectations, and Color Tone
When you request a "tint match" for a Bmw 2 Series Gran Tourer rear glass replacement, we first confirm whether you are matching factory privacy glass or added tint film. Privacy glass is dyed in the glass; film is applied to the inside surface later. If your Bmw 2 Series Gran Tourer originally had privacy glass, the most OEM result is installing OEM-quality privacy rear glass with the correct DOT/AS markings and built-in shade. Then we evaluate VLT, net VLT, and tone. VLT (Visible Light Transmission) measures how much light passes through a single layer. Factory privacy glass on many SUVs and trucks is often around 15-26% VLT, while clear glass may be closer to 70-85% VLT, so a clear replacement can look obviously different. If the prior rear window also had film, the final shade is net VLT (glass plus film), so plan to re-tint after replacement for a true match. Tone is the next giveaway: some privacy glass leans charcoal/gray, others show a green or bronze cast, and it should track your other rear panels. Because tint rules vary by {state}, we focus on duplicating what you had. Bang AutoGlass is mobile in {city}, {state}, often available next day, and every rear window replacement is backed by a lifetime workmanship warranty.
Rear Defroster Grid Basics: Lines, Power Tabs, and What Common Failures Look Like
The rear defroster grid on your Bmw 2 Series Gran Tourer is a simple heater circuit that restores visibility in rain, humidity, and winter weather. The thin horizontal lines on the inside of the rear glass are conductive traces, fed by two vertical bus bars. When you press the defrost button, the system typically applies about 12-14 volts through bonded power and ground tabs on the glass, warming the surface to clear fog and light frost. Because the connection is made at those tabs, a loose connector, corrosion, or a detached tab can stop the entire grid even if the lines look intact. If only part of the window clears, that usually points to broken grid lines, often caused by scraping ice, removing stickers, or using abrasive cleaners. If the indicator light is on but nothing clears anywhere, common upstream causes include a blown fuse, bad relay, switch issue, control module fault, or poor ground. During an OEM-quality rear glass replacement on your Bmw 2 Series Gran Tourer, we verify the correct grid pattern, tab placement, and connector fit so the defroster works after the rear window replacement. Bang AutoGlass is mobile, often available next day, and our installs are backed by a lifetime workmanship warranty.
Install Prep That Protects Fit: Interior Protection, Pinchweld Checks, and Bond Surface Readiness
Rear glass replacement quality on a Bmw 2 Series Gran Tourer is determined before the new panel is ever set. Bang AutoGlass starts by protecting the interior—seats, headliner, trim, and cargo area—then removing necessary moldings and liftgate panels and vacuuming thoroughly to keep debris out of latches and interior panels. Next we inspect the pinchweld/bonding flange for rust, paint damage, and signs of prior substandard repairs that can compromise urethane adhesion. Standard stationary-glass practice is to trim existing urethane to a thin, uniform layer (about 1–2 mm) so fresh urethane bonds reliably to a stable base while minimizing exposed metal. If bare metal or corrosion is present, we address it with proper surface prep and the correct primer for the adhesive system. We then dry-fit OEM-quality rear glass to confirm alignment, molding fit, and consistent gaps, prep the glass frit and vehicle bonding surface with approved cleaner/primer, and lay a consistent urethane bead before setting the glass square to avoid leaks and whistles. We're mobile in {city}, {state}, often next day. Most installs take 30–45 minutes plus at least one hour of safe cure time. Every job includes a lifetime workmanship warranty, and we work with all insurance companies when comprehensive coverage applies.
Defroster Reconnect and Testing: Tabs, Harness Connection, and Function Verification on Bmw 2 Series Gran Tourer
Defroster reconnection is a critical step after a Bmw 2 Series Gran Tourer rear glass replacement because the system depends on solid electrical contact at the glass terminals. The heating grid is printed on the inside surface and connects through two bonded tabs—power and ground—plus a short harness connector. After installation, we confirm the harness reaches naturally and tab placement matches the factory layout for your Bmw 2 Series Gran Tourer. If the harness is forced, tabs can loosen later, so we reconnect with controlled, straight pressure rather than twisting or levering. We also verify the connector is clean and fully seated; partial seating can cause intermittent heating or a no-heat condition even when the grid looks perfect. Functional testing is simple: with ignition on and the defroster switched on, you should typically see near battery voltage at the terminals and feel the grid begin warming within about a minute. If nothing changes, start with fuse/relay and then switch/control and ground integrity. If only some areas clear, the usual culprit is broken grid lines from scraping ice, decal removal, or abrasive cleaning. Use non-abrasive products to protect the traces. Bang AutoGlass is mobile across {city}, {state}, often next day, and every install includes a lifetime workmanship warranty.
Aftercare and Final QC: Safe Drive-Away Timing, Leak/Wind Noise Checks, and Defroster Use
We close out every Bmw 2 Series Gran Tourer rear window replacement with final QC and clear aftercare, because the first 24–48 hours influence long-term sealing. On-site, we confirm the glass sits square, the reveal is even, and moldings and interior garnish trim are flush. We inspect the urethane line for continuity around the perimeter, since small voids can later translate into water entry or wind noise. We also verify the rear defroster connection is secure and the grid responds when commanded on. Most rear glass replacements take 30–45 minutes, followed by at least one hour of safe drive-away time for the urethane to set. Because cure continues after you leave and weather in {city}, {state} can affect it, keep stress low the first day: avoid slamming doors, rough-road impacts, and cabin-pressure changes. Skip automatic or high-pressure car washes for at least 48 hours and don't aim water jets at the perimeter. If retention tape is applied, keep it on as directed. Defroster testing is fine, but avoid long cycles for about 24 hours. If you notice leaks, whistling, or trim movement, Bang AutoGlass will address it under our lifetime workmanship warranty, and we work with all insurance companies when comprehensive coverage applies.
Enjoy More Relevant Blogs
Rear Defroster Not Working on Bmw 2 Series Gran Tourer? When Rear Glass Replacement Makes More Sense Than Repair
Rear defroster not working on your Bmw 2 Series Gran Tourer? Learn common causes, when repair fails, and when rear glass replacement is the smarter fix for winter.
Tempered Safety Rear Glass Replacement for Bmw 2 Series Gran Tourer: Understanding DOT Markings and FMVSS 205
Need Bmw 2 Series Gran Tourer rear glass replacement? Learn tempered safety glass basics, DOT markings, and FMVSS 205, plus install and cure tips. Get a quote today.
Back Glass Replacement on Bmw 2 Series Gran Tourer: Defroster Tabs, Antenna Lines, and Connector Reattachment Basics
Back glass replacement on Bmw 2 Series Gran Tourer: defroster tabs, antenna lines, and connectors explained, plus install tips to avoid damage and rework safely.
Rear Glass Replacement for Bmw 2 Series Gran Tourer: What to Expect During Install and Aftercare
Rear glass replacement for Bmw 2 Series Gran Tourer: what happens during install, defroster and tint considerations, cure time, and aftercare to prevent leaks long-term.
How to Schedule Mobile Rear Glass Replacement for Bmw 2 Series Gran Tourer
Schedule mobile rear glass replacement for your Bmw 2 Series Gran Tourer in minutes. Learn what info to provide, how long it takes, and prep tips for service day.
Post-Install Checks for Bmw 2 Series Gran Tourer: Rear Glass Replacement Wind Noise, Leaks, and Rattle Tests
Post-install rear glass checks for Bmw 2 Series Gran Tourer: test for wind noise, leaks, and rattles, plus when to return for warranty service—check today before trips.
Shattered Back Window on Bmw 2 Series Gran Tourer: A Step-by-Step Rear Glass Replacement Plan
Shattered back window on Bmw 2 Series Gran Tourer? Follow a step-by-step rear glass replacement plan, cleanup tips, defroster notes, cure time, and drive-away rules.
How Much Does Rear Glass Replacement Cost for Bmw 2 Series Gran Tourer? Pricing Factors, OEM vs Aftermarket, and Insurance Deductibles
Estimate Bmw 2 Series Gran Tourer rear glass replacement cost. Compare OEM vs aftermarket, labor factors, insurance deductibles, and ways to save. Request a quote.
How Long Does Rear Glass Replacement Take on Bmw 2 Series Gran Tourer? Install Time, Adhesive Cure Time, and When It’s Safe to Drive
How long is Bmw 2 Series Gran Tourer rear glass replacement? Get install time, urethane cure guidelines, and drive-away timing after service. Plan your visit today.
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm
Bang AutoGlass
Quick Links
Services
Auto Glass Services by Makes & Models
Customers
Insurance Companies
Mailing Address
936 SW 1st Ave PMB 877 Miami Florida, 33130
Sales: Monday - Sunday , 24/7
Support: Monday - Friday , 10am to 7pm