Where to Place SunPass After a New Windshield in Riverview
THEA gives two specific clearances for a SunPass PRO: place it at least 2 inches below the windshield frame and at least 2 inches below a solar strip. These are PRO instructions, so use the current directions supplied with a replacement Mini for that sticker.
Where to Put SunPass on a New Windshield
Start by locating the rearview mirror and any plastic housing attached behind it. That housing may contain a forward-facing ADAS camera, a rain sensor or both. The transponder belongs on the glass in a permitted mounting position, not on the camera housing, over a lens opening or on top of a sensor pad.
Do not assume the empty-looking area beside the mirror is available. A camera sees the road through a defined part of the windshield, and a sensor may use the glass directly in front of it. Keep the SunPass, dash-camera mount and phone mount outside those working areas.
Use the vehicle manual to identify any no-mount area that is not obvious from the plastic housing. The camera's view through the glass can extend beyond the visible lens opening, so looking only at the edge of the cover is not enough.
Windshield Solar Strip and Transponder Placement
A solar strip is the dark or shaded band across the upper portion of some windshields. Windshield solar strip and transponder placement belong in the same check: a spot 2 inches below the frame can still be too close to a strip that extends farther down the glass, and THEA requires the PRO to sit at least 2 inches below the strip too.
Use this order when selecting the position:
- Identify the device as a Mini or PRO.
- Find the windshield frame and any solar strip.
- Locate the ADAS camera, rain sensor and mirror housing.
- Read the current SunPass and vehicle-manufacturer instructions.
- Mount the device only after all required clearances are satisfied.
Wait until the windshield, mirror hardware and sensor covers are back in place before choosing the final spot. That lets you judge the actual available glass instead of attaching the transponder beside a component that still needs to be fitted.
Measure and check the camera area before pressing a replacement Mini onto the glass, because it gets one attempt. A PRO can be repositioned, but it still needs a stable suction mount and the required clearances.
After mounting the device, sit in your normal driving position: a spot that meets the toll-device measurements still must not block your sight line or the camera's view of the road.
Photograph Other Items Attached to the Windshield Besides the SunPass
Take one wide photograph of the entire windshield and close photographs of every decal, mount and cable before the appointment.
- Parking permits and workplace access decals
- Community gate or property-access stickers
- Dash-camera mounts and their cable routes
- Phone mounts attached by suction or adhesive
A photograph records the old location, but it does not make an adhesive item reusable or approve that position on the new glass; the new camera housing and sensor zones take priority over the old layout.
Record the permit number you may need when asking an issuer for a replacement. Only the issuer can decide whether a peeled parking, gate or workplace decal remains valid.
Unplug removable electronics and put them with your personal items. Leave factory camera covers, mirror hardware and rain-sensor components in place for the glass work. Do not pry around the plastic housing behind the mirror.
Update the SunPass Account Before the Next Toll Trip
Managing a transponder after auto glass replacement in Florida has two separate parts: the physical device on the windshield and the information held by SunPass.
Removing a device does not update the account automatically, so use SunPass support and account tools for its current process.
A mounted device is not proof that it is active on the intended account, and a plate listed on the account does not make a peeled Mini reusable.
- Tell SunPass that the old Mini was removed with a replaced windshield.
- Follow its directions for deactivating that Mini and obtaining a replacement.
- Confirm when the new Mini or saved PRO is active on the intended vehicle.
- Check that the license plate and vehicle information are current.
- Review the account after the first toll trip with the new glass.
If another toll trip is planned before the replacement Mini is active, ask SunPass how to handle it; the Selmon network does not accept cash.
Cameras and Sensors Change the Available Mounting Area
Modern windshields can include a bracket for a forward-facing ADAS camera, a rain sensor, acoustic material or a head-up display area. These features affect glass selection and leave specific parts of the windshield unavailable for a transponder or accessory mount.
Replacing a windshield that supports a forward-facing camera can require recalibration because the camera's relationship to the new glass and the road must meet the vehicle manufacturer's specifications.
Once recalibration is complete, adding a transponder or dash-camera mount within the forward camera's field can block part of the road scene the system reads. Calibration does not compensate for an accessory physically covering that view. A mount can sit above the driver's eye line and still overlap the camera opening, so inspect the final layout from outside the windshield as well as from the driver's seat.
If the camera behind the mirror needs recalibration once the replacement glass is set, we complete ADAS Calibration during that same visit where the procedure can be done on site. The vehicle’s driver-assistance system determines the recalibration process.
For Windshield Replacement, we cut out the damaged glass, prepare the bonding surface, apply a fresh urethane bead and set the replacement. Its camera bracket, rain-sensor provision, head-up-display area and other built-in features must correspond to the vehicle. We use OEM-quality glass matched to that equipment.
If the vehicle requires camera recalibration, complete that work before rebuilding the transponder and accessory layout around the mirror.
Fresh urethane needs time to reach the strength required for driving. Follow the drive-away instructions given for the installation. The first-day windshield aftercare steps explain how drive-away time, retention tape and car-wash timing differ.
Have the year, make, model and VIN ready when booking, and identify any camera or sensor behind the mirror. Our Mobile Auto Glass service comes to the vehicle anywhere in Riverview, provided it is parked safely with enough working room around the windshield.
Book Windshield Replacement in Riverview
For SunPass after a new windshield in Riverview, tell us whether you have a Mini or PRO when you book and complete this checklist before the glass work:
- Leave a SunPass Mini attached to the old windshield.
- Remove a SunPass PRO and store it in a closed compartment.
- Photograph decals, permits and electronic accessory positions.
- Have the VIN and windshield feature details ready.
- Contact SunPass for replacement and account instructions.
- Park the vehicle where the windshield perimeter can be reached safely.
Provide gate or parking instructions when needed, and remove loose items from the dashboard before the appointment.
If insurance may apply to the Riverview windshield, have your policy information ready. Review the Florida auto glass insurance guide before speaking with your insurer. Florida Statute 627.7288 excludes windshield damage from the deductible provisions of comprehensive or combined additional coverage. Its text does not extend that rule to door, rear or sunroof glass. We verify coverage before any work, help you with the claim and bill your insurer directly. General info, not legal or insurance advice — coverage varies by policy.
Use the Riverview mobile auto-glass service page to book, and tell us whether the vehicle carries a SunPass Mini or PRO. A no-obligation quote by phone is available at (877) 994-5277. New appointments are accepted 24/7; installation hours are Monday through Saturday, 8 a.m. to 6 p.m.
Hablamos español. The installation includes the Bang Lifetime Workmanship Warranty for as long as you own the vehicle.
SunPass and Windshield Replacement FAQs for Riverview
Can I reuse a SunPass Mini after windshield replacement?
No. The Tampa Hillsborough Expressway Authority says a SunPass Mini no longer works after it is removed from the windshield. Leave it attached until the old glass is removed, then contact SunPass for current replacement, deactivation and activation instructions.
Where should I put a SunPass PRO on a new windshield?
THEA says the SunPass PRO must be at least 2 inches below the windshield frame and at least 2 inches below a solar strip. Keep it away from the forward-facing camera, rain sensor and plastic housing behind the rearview mirror. Check the vehicle manual and current SunPass instructions before choosing the final position.
Should I remove a SunPass PRO before windshield replacement?
Yes. Remove the portable, suction-mounted PRO before the appointment and store it in a closed compartment. Remount it after the new windshield is installed, following THEA's mounting instructions and clearance rules.
Can a mobile windshield replacement in Riverview move my SunPass?
Bang AutoGlass can complete Windshield Replacement where your vehicle is parked safely, but the device type determines what moves. Remove and keep a SunPass PRO before the appointment. A SunPass Mini cannot be transferred as a working device after it is peeled from the old windshield, so contact SunPass about its replacement.
What should I check before my first Selmon Expressway trip with new glass?
Confirm that the replacement Mini or saved PRO is active on the correct SunPass account, verify the vehicle and license plate information, and inspect the physical mounting position. After the trip, review the account activity. Contact SunPass if the transaction or device status does not match what you expected.
